How to SOLDER WIRES TOGETHER - PRO TIPS for WATERPROOF CONNECTIONS

Рет қаралды 14,756,527

Күн бұрын

How to SOLDER LIKE A PRO but in a way anyone can learn. TIPS to make permanent, waterproof connections. Perfect for auto, RV, boats & power equipment. If you are going to make a connection, be sure it will last and keep your equipment running. If you love my solder sleeve connectors • Never Solder Again - H... KEEP USING THEM but if you have to solder the old school way, now you can supercharge it.
Weller Solder Iron: amzn.to/3gbUKqh
3M Silicone Paste: amzn.to/3x55s8z
Soldering Flux: amzn.to/3in5PYm
Electrical Solder: amzn.to/3fTUptc
Heat Shrink Kit: amzn.to/3psLrqf
Quad Hands: amzn.to/3io9zZA
0:00 Getting Started and Secret Tools
2:13 Good Part How to Solder
NONE of these products or companies are sponsored. I use this stuff everyday & buy it myself.
This video, description and comments contain affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. This helps support the channel and allows us to continue to make videos like this. Thank you for the support!
Disclaimer:
Due to factors beyond the control of Silver Cymbal, I cannot guarantee against improper use or unauthorized modifications of this information. Silver Cymbal assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Silver Cymbal recommends safe practices when working on machines and or with tools seen or implied in this video. Due to factors beyond the control of Silver Cymbal, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Silver Cymbal.

Пікірлер: 1 300

@SilverCymbal 3 жыл бұрын

Thanks for watching - PLEASE LIKE & SUBSCRIBE 🔥My favorite tools: www.amazon.com/shop/silvercymbal

@engineer_pirate_hunter 3 жыл бұрын

You should've had the NASA method ,just to show people what overkill looks like

@calimesacox 3 жыл бұрын

Finally someone who can show how to solder... Thank you

@Trigger505 3 жыл бұрын

@@engineer_pirate_hunter Or all of the IPC approved methods. I actually use the NASA method for solid wire or components to stranded wire.

@paulevans8849 3 жыл бұрын

@@engineer_pirate_hunter 0

@pirvirts 3 жыл бұрын

Тот момент когда паяешь такие провода обычной зажигалкой с турбинкой

@MeiklesAndDimes 3 жыл бұрын

Pro tip: Remember to slide the heat shrink on the wire BEFORE soldering the joint!

@SilverCymbal 3 жыл бұрын

Very good point!!!!!

@THESOHAILKHAN1992 3 жыл бұрын

lols i wish i have seen this tip a year ago

@eosjoe565 3 жыл бұрын

For sure. There's nothing worse than attaching a complex connector and then discovering you forgot to slide on the heat shrink! :-)

@snap-off5383 3 жыл бұрын

When you screw it up, liquid electrical tape can save your butt.

@B3ASTM0D3. 3 жыл бұрын

🤣🤣🤣🤣🤣 that would be preferable.

@dand8282 3 жыл бұрын

Touching the solder to the iron, just a little bit to melt a small blob on the wire/iron junction while warming the wire will help it heat much faster as the liquid metal provides a better thermal conduction than two solid round metal things rubbing.

@robertbrawley5048 3 жыл бұрын

I keep trying that the coil solder would drop off about a half inch of it at a time

@snap-off5383 3 жыл бұрын

Yeah, the never touch the solder to the iron rule is too overly cautious, just don't do a cold solder.

@chrismorris1304 3 жыл бұрын

Yes yes

@dcgo44r 3 жыл бұрын

If you are soldering delicate electronics with that "chip-hammer" you are risking melting the jackets, or something along the cable or circuit board. A dab of solder on a pencil tip is more than enough if you can't control the heat when it's too much!

@Blindman875 3 жыл бұрын

Came here to say exactly this.

@byronwatkins2565 3 жыл бұрын

First, the rosin will melt and wick into the wire mesh once heat is applied so there is no need to waste time working it in. Second, isopropyl alcohol will clean off the flux after the solder is applied. Third, it is important to slide the heat shrink tubing over one of the wires before making the connection; it must be slipped over an open end and frequently the connection joins the last two ends.

@Filmhome274 3 жыл бұрын

kzfaq.info/get/bejne/q9abeNVj3bHRhI0.html

@jonmayer 3 жыл бұрын

Yes, your comment is a better tutorial than this whole video.

@Pseudoswede 3 жыл бұрын

@@jonmayer This kinda comment is exactly why I keep coming back to the interwebs. It’s almost like an abusive relationship, where these golden moments of sarcasm, satire, and irony are what make enduring all the other insanity and bovine scatology worthwhile. A long winded way of saying “keep smackin’ her,” metaphorically speaking;)

@seekhimwithallyourheartand3358 2 жыл бұрын

Repent to Jesus Christ “I will refresh the weary and satisfy the faint.”” ‭‭Jeremiah‬ ‭31:25‬ ‭NIV‬‬ I

@bodeine454 2 жыл бұрын

"and frequently the connection joins the last two ends." I don't understand this last sentence, what does it mean? 🤔

@richarda.valdes1197 3 жыл бұрын

Remind the person that’s since the wires do not normally have a running end it’s best to slid the shrink tubing on before soldering.

@imacrazyguy5831 3 жыл бұрын

My rule of thumb is a mechanical bond first (bend each wire into the other and twist), followed by the solder. Working around vehicles and wiring them up, they are subject to vibrations and solder loves to crack with vibrations if the wires arent mechanically bonded first. Followed up with Marine Grade heatshrink, the internal glue further reinforces that mechanical bond and creates a weatherproof seal.

@Filmhome274 3 жыл бұрын

kzfaq.info/get/bejne/q9abeNVj3bHRhI0.html

@JustAPersonalUseBarb Жыл бұрын

You should be using cold welds instead of solder due to this. It sounds counter-intuitive, but crimps are the way to go. Cold weld joints are much more durable, even if that sounds weird

@dwaynemcallister7231 Жыл бұрын

@@JustAPersonalUseBarb As long as you don't mind more resistance

@NithinJune Жыл бұрын

tf is “marine grade heat shrink”

@jackster2568 10 ай бұрын

@@dwaynemcallister7231Absolutely, factually, incorrect. I'm sure you're happy with the hairline fractures that develope in a vibrating environment in the soldered connection as well as the fact that you're going against the grain of the marine and aviation industries.

@Abe_Rudder 3 жыл бұрын

Explains the best way to solder, proceeds to show us the WOSRT soldering I have ever seen.

@rockefelleragent1357 4 ай бұрын

God told me that this soldering technique is fine minus the use of flux... you don't need flux.

@Maver1ck911 4 ай бұрын

@@rockefelleragent1357Flux is phenomenal. But these channels are all jazzed about preventing corrosion and shrink tubes and silicon grease BUT THEY NEVER CLEAN THE EXCESS FLUX OFF

@marvinostman522 Жыл бұрын

I am glad to see this. I did this for 17 years making custom looms for trucks. I would have my tape ready so I could wrap it while it was hot. It helped the tape to seal. I used the fist method.

@dtibor5903 3 жыл бұрын

I work in electronics manufacturing and I don't 100% agree. Especially the grease on the wires is not needed. There are many ways to connect wires. All the industrially accepted wire connection methods are in the IPC standards. There are many shrink tubes with hot melt inside, that is corrosion resistant without silicon grease. Also don't use this soldering pistol for electronics soldering.

@orson091 3 жыл бұрын

those self solder heat shrink tubes are my new favorite thing for quick jobs in the workshop or a car/trailer. also perfect for keeping in the ute when all you need is a heat source to do the whole job.

@DigitalIP 3 жыл бұрын

Personally i dont see a problem with using dielectric grease with heat shrink, may not need it but it definitely doesnt hurt.

@kenthawkins2418 3 жыл бұрын

@@DigitalIP That's what I've done, and I agree .

@Trigger505 3 жыл бұрын

Thank you. And he didn't mention matching the flux to the solder being used. If the solder has a flux core, the flux used MUST match the type used in the core. Same goes for solder wick. Best way to go is unfluxed so that you can just use what you have. And yeah, those gun irons suck for any kind of precision as well as heat control. PVC 300V has the tendency to melt, shrink back, and burn with too much heat applied. It really is best to put a bit of solder on the iron and use the flux in the core to start the flow rather than getting 8" of the wire up to 250 degrees and melting everything.

@staircapades 3 жыл бұрын

I use IPC 620 standards at work myself and found this video to be mostly inaccurate.

@thekooj 3 жыл бұрын

This was video made sodering wires way more complicated than it needs to be.

@conscireshooter 3 жыл бұрын

This video is for making waterproof connections. You need these for places that regularly come in contact with water. Like in industrial water purifiers, rooftop solar panels or even garden wiring that will be buried under earth.

@akhileshchunam5094 3 жыл бұрын

Advertising products a lot

@CptSpears007 3 жыл бұрын

Congratulations you made two mistakes in your comment while trying to be a smart ass

@Bobodeman 3 жыл бұрын

Ive got a cheap soldering iron and it works fine. Been using for years The 2nd one is how i first started soldering, also started by using solder against soldering iron. Then my dad learnt the proper way then showed me

@awsfernandez63 3 жыл бұрын

Thank you for sharing this video! Lots of young people nowadays have never used a soldering iron/gun.

@TheCarpenterUnion 3 жыл бұрын

Alternate title: Fighting with an Archaic Soldering Iron for 10 Minutes

@joewoodchuck3824 3 жыл бұрын

I didn't even think they were still made. I don't see any point to them.

@alanowa123 3 жыл бұрын

@@joewoodchuck3824 they heat up way way faster than pen-style irons at the same price Edit: and they provide full electical isolation from mains, cheap soldering irons can fuck that up and screw you and your electronics with 120/240v

@devnol 2 жыл бұрын

@@alanowa123 you can buy a usb-c powered pinecil or miniware TS100 for around 30 usd that heats up to 300C in less than 15 seconds

@andrewscott2090 3 жыл бұрын

Thank you for sharing I learned a few things that I didn't know before thank you very much

@mrt1r 3 жыл бұрын

Nice presentation. It is good to note that the lineman's splice is used in situations where the wire may be under strain. It is so called because it was traditionally used in the telephone industry to patch phone line. If done properly, the splice is stronger than the wire.

@WayneRiesterer 6 ай бұрын

Amazing job. Cleaning with acetone before and after helps as well. Also, if you add a little bit of solder to the tip before applying it to the wire, it forms a heat bridge and heats up the local area quicker and the application of solder to the conductor will be really quick. I love the tips regarding rosin flux and silicone grease. Nice work!

@-Galavanta- 3 жыл бұрын

Put a little bit of solder on the tip of the solder gun first, it will transfer the heat to the wire faster and more efficiently.

@TWOSU_NEWS 3 жыл бұрын

Pro Tip: ***contrary to the instructions on this video, the proper way to solder is to completely coat the exposed wire with solder were you can no longer see individual strands, this ensures complete depth and prevents hot spots in the wire joint...remember, to apply enough solder that it complete covers every strand without excess run off***

@shouldabeengone 3 жыл бұрын

So did he use too little? Other people in the comments are saying he used wayyy too much.

@benzo5799 3 жыл бұрын

@@shouldabeengone what he did is perfectly fine, if you it like in the video you will pretty much get a perfect connection every time, what truckers wall of shame said is to presolder the ends of the wire, which is sonething youd do when soldering the wird to a connector or something but certainly not when connecting 2 wires. Just du it like he did in the video, preferably the first method, hope i can help you ✌🏻

@TWOSU_NEWS 3 жыл бұрын

@@shouldabeengone even though he probable got a full connection, he used to little...people forget that the melting point of solder is lower than the burn point of the insulation. Electrical wiring can get hot enough to melt solder., when doing electrical wires you want the most amount of solder possible to dissipate the heat...because of this, he used to little...dont get me wrong, I'm not bashing him...his technique is good, just needed to add a bit more solder

@UserFormelyKnownAs_hjkh 3 жыл бұрын

Agreed. He didnt use enough solder in the first joint. You should not be able to see bare copper the way you can at the bottom of his 1st connection. To boot, the silicone paste should be on the insulation as well as the bare wire before installing the heat shrink tubing. This will ensure 100% waterproof behind the heat srink as well as the joint.

@johnmoloney5296 3 жыл бұрын

Spot on you tin the wire before soldering it 👍👍

@Saiimunn 3 жыл бұрын

Me when I want to make a water tight connection I use small pieces of hot glue that I put in the heat shrink tube and when I apply heat it melt the glue and seals everything. The plus with the hot glue is that the solder now has a strain relief and it won't break as easy just beside the solder in an application where the wire would band alot.

@karaokedeconstruction 9 ай бұрын

there are many how to solder videos out there but for me this is the most concise with the best tips for a beginner

@stevenwdoolittle1195 2 жыл бұрын

Yes,make sure you put your heat shrink tube on the wire before you put wires together then add your stuff. Great tips!

@user-rd3kr6pp1h 3 жыл бұрын

Messed up. The isolation is overheated and melted. If that was multiple phase hi-voltage wire that would cause the fire hazard. Mistake was about melting the tin through the wire directly. Took too much time. If you drop the melted tin on the cold wire covered the flux, it would be saturate exactly the same way.

@mitchhifi9192 3 жыл бұрын

Fine for ultra low voltage, high voltage insulation also doesn't bubble and warp anywhere near as easily

@Cola.Cube. 3 жыл бұрын

You wouldn't want to solder a joint on a high voltage cable, I imagine that's against the regs, you would need to use a clamp joint, and faulty cables should be replaced, not repaired if at all possible. Remembering high voltage is 35 to 230 Kv.

@fsdfmsbcxx 3 жыл бұрын

Right @ d dpo1r

@mitchhifi9192 3 жыл бұрын

Yeah should note I've never soldered anything over 24v. My note of the strength of high voltage insulation comes from heat shrink covering crimped lugs.

@catch.22 3 жыл бұрын

@@Cola.Cube. for navy regs and all shipwork they specify its fineable offense, and I know thats consistent in all ports in the US where the navy is.

@MMYLDZ Жыл бұрын

Pro tip, after touching the sodding iron to the wire for a second or two, add a little solder right where the iron is touching the wire to make it conduct heat much faster to avoid melting the insulation.

@musiciansimon8562 16 күн бұрын

Bro, this is Simon from Amritsar, India. You helped me a lot,today only I was installing the wires for my ac and this time I was make all wires under wall. You saved my money

@Dionysor 2 жыл бұрын

thank you for the up. when i learned this back in college they skipped quite some steps but everything still holds. can recommend the dremel rod that uses lighter gas. will spend on the electric big boy later

@shaoyang5650 3 жыл бұрын

Almost anyone can do this when the you have such easy access to the wires. In most cases it’s not easy to access the wires you need to work on.

@treeguyable 3 жыл бұрын

Was gonna post the same thing, but all these tutorial vids are made the same way we would probably make them, for instruction, then it is up to the repairer to apply these principles the best way possible, lying on your back, in the mud, under the truck, in the winter, 30 mph wind, or cramped up, in your bobcat, or under the hood of the car, 100 degrees out ,max humidity, mosquitos and ants all over you.

@GerPornflakes 3 жыл бұрын

bluethooth on ear heqdphones😂😂😂😂😂

@GerPornflakes 3 жыл бұрын

and there are also lots of devices, where they isolate the wire with paint, or the core is made out of plastic 🤧very bruh

@GerPornflakes 3 жыл бұрын

sorry, fiber glass*

@cosdonamo 3 жыл бұрын

@@treeguyable i wouldnt advise solder if the cable is going to flex or vibrates a lot, there are better and quicker methods for that (clamping them together with a connection piece idk if there is an english term)

@Mr_Spooner 3 жыл бұрын

I would not recommend that giant clunky Weller. There are tons of inexpensive and smaller units that are waaaaay easier to hold. Some even have adjustable temps. Dont buy the Weller gun

@Watcher3223 3 жыл бұрын

I agree. A soldering gun with over 200 watts of power is overkill if you're just soldering together a couple of low voltage wires. A 30 or 40 watt soldering iron is more reasonable for the application. Weller also makes smaller soldering irons as well as more precise temperature-controlled soldering stations.

@nebulousisgod 3 жыл бұрын

That’s what I was thinking too. I haven’t had to use one of those since the 90s. But it does have a trigger to control the heat and a lot of the cheaper lighter ones just stay on and hot as long as they’re plugged in.

@BangBang-hk4rg 2 жыл бұрын

Agreed 👍

@HungryH1951 10 ай бұрын

Very good. I now feel like I can solder some wire more successfully. Thanks for posting!

@ASH7388 3 жыл бұрын

I usually make two hooks with the exposed wires, twist it twice, before wrapping it tight. This gives its a bit more tensile strength instead of just holding it together by the solder

@themadatheist1976 3 жыл бұрын

Another soldering sponge tip is to get a old film canisters you use to drop your film off in stores to develop and fold your sponge into it. Most sponges that come with your irons don't need to be cut and you can just keep the sponge moist when you put the cap back on. The film canisters can also store brass type solder cleaners.

@Filmhome274 3 жыл бұрын

kzfaq.info/get/bejne/q9abeNVj3bHRhI0.html

@AlexKunstar Жыл бұрын

What year are you living in buddy? I forgot those film canisters even existed 🤣

@jabba334 3 жыл бұрын

As someone who's had a J-STD-001 Solder Certification, this is a good video! Thumbs up!

@darrylm3627 Жыл бұрын

GoodStuff,GreatTips😀👍🏿

@rudypacheco91 3 жыл бұрын

Very thorough!

@mattweger437 3 жыл бұрын

Woah, okay Weller makes a good iron on the top end but for a cheaper iron the ts-100 is hands down the best

@B3ASTM0D3. 3 жыл бұрын

Rosin core solder is also acceptable without the additional flux treatment beforehand. The 3m silicone and heat shrink is a must for any wet low voltage locations. Great video.

@NetBood 3 жыл бұрын

Just saw this in my feed and decided to watch, very informational, who knows if I may need this in the future

@brianlafollette7530 2 жыл бұрын

Great job keeping straight to the point.

@tunina6421 2 жыл бұрын

Ideally you would just want to tin each end and then solder the two tinned ends together. IPC recommends never twisting a copper wire because copper becomes more brittle the more you bend it and this will be amplified in environments with temperature extremes. Contorting wires like this video does would make it more likely that solder does not make full coverage on each individual strand. Also dialectic grease is a bit unnecessary. I think a good appropriately sized shrink tubing with adhesive should seal it and insulate well. If you are really worried, just layer the tubing

@kingcrumpet Жыл бұрын

When you say "solder the two tinned ends together", do you mean just placing the two ends side by side so they overlap, then just touching them with the iron so the existing tin joins the ends? Or use fresh tin?

@tunina6421 Жыл бұрын

@@kingcrumpet the first thing you said. Tinning just refers to flowing solder on the wire. I will say that doing this by hand isn't always simple, but something I did when I did this in a production line was make wooden races for different gauge wires and then I wouldn't need 3 arms to hold the 2 wires while soldering.

@kingcrumpet Жыл бұрын

@@tunina6421 Understood, thank you for replying so quickly. I need to solder in a new section of ignition coil wiring tomorrow to get my friend's car running again. I think rats chewed through it! Nothing like working on a production line to make you good at something!

@rocketboyjv5474 3 жыл бұрын

I've had bad experiences with Weller soldering guns. Bought a ts 100 recently and it works much better

@shouldabeengone 3 жыл бұрын

My Weller iron at work sucked so bad, I switched to a hakko and it was 100% easier than the Weller.

@PM-Ghost17 3 жыл бұрын

The TS-100 and TS-80 are absolute beasts

@ChezJ1 3 жыл бұрын

GREAT tutorial thank you.

@djsnglzz Ай бұрын

Thanks for a great video. 😊

@bagelgeuse5736 3 жыл бұрын

Don't know why KZfaq recommended me this. I'm never going to solder wire but I still enjoyed the video for some reason.

@LeDragoX 3 жыл бұрын

Yeah, oh no that Bazel sound again... Must stop it with my Insect Glaive

@bagelgeuse5736 3 жыл бұрын

@@LeDragoX The dive bomber just wants a hug

@LeDragoX 3 жыл бұрын

@@bagelgeuse5736 Nooooooo! ! !

@severinofioletti9765 3 жыл бұрын

Wires can be soldered, only for static positioning, otherwise in a machinery enviroment, vibrations will break the wire next to the soldered area 😉

@polla2256 3 жыл бұрын

The battle field says just get the damn thing working and back into the fight.

@cosdonamo 3 жыл бұрын

@@polla2256 the battlefield also provides you with electric energy to weld right? on the battlefield you just use solderseal wireconnectors, clamp it and heat with lighter or just tape it together till in a safe area

@murk1352 3 жыл бұрын

I've had that Weller soldering iron for over 40 years & it still works amazing and I've done some serious soldering with it. I use to tub out my models with it. Pull the trigger and cut through the plastic. I cleaned the same tip off when I got older and it's still mint...!

@lontret2828 3 жыл бұрын

Perfect guide!

@TheJellybeanDrifter 3 жыл бұрын

Today I learned everyone in the comments section has a PhD in soldering lol

@garyalensr 3 жыл бұрын

Sir you absolutely save me so much aggravation. I was really never good at soldering until using your tips and tricks. You have got the best DIY and review channel on KZfaq!!! Thank you so very much for all your awesome vids. KEEP UP THE GREAT WORK

@darrelmartin8261 3 жыл бұрын

100

@sjsuper1976 3 жыл бұрын

Great video, thank you!

@johnbugman1 2 жыл бұрын

epic waterproofing tip!

@Apophis-en9pi 3 жыл бұрын

Love your videos, but I think this one should be revisited. NASA uses the Lineman's Splice for a reason - it's better. Also called the Western Union Splice. Skip the grease and use waterproof adhesive heat shrink. Normal heat shrink has no adhesive and the only keeping it slid over the joint is friction and shape. With the waterproof heat shrink the adhesive on the inside glues it to the insulator, solder joint, everything. Lastly, I'd use a soldering iron vs gun for this.

@Filmhome274 3 жыл бұрын

kzfaq.info/get/bejne/q9abeNVj3bHRhI0.html

@smilingryu2274 3 жыл бұрын

New subscriber here love it keep the wiring and electrical tips coming

@SilverCymbal 3 жыл бұрын

Thanks for the sub!

@d.e.c1609 4 ай бұрын

Excellent way to wind the wires. The solder joint was pretty good, too! Considering most electricians don't care.

@liveletlive3348 2 жыл бұрын

_Most of the people do these kinds of work just for the heck of it & that's quite temporary_ *But this work looks neat, smooth & durable* _I wish electricians/technians in my area work with such detailing & precision_ ⚡️

@smash461986 3 жыл бұрын

I don't remember seeing that in the IPC standard. Splitting wires is usually a no no. Be better to line the trimmed ends side by side and solder.

@townfool6859 3 жыл бұрын

Remove flux residue, and clean the connection, with alcohol after soldering.

@myaccount6129 8 ай бұрын

Really thank you for these valuable info in that short and polite and balanced video

@scottcarlson2788 Жыл бұрын

Fantastic lesson.

@ElvinHasBecameAWeeb 3 жыл бұрын

i dont even solder, but this vid got recommended to me, and i was pleased

@user-zo6lj4sm1q 3 жыл бұрын

Капиталисты дают конечно... Зачем все это, если есть изолента?)) И никогда не видел, чтобы медь ржавела...

@MagikalKrabical 3 жыл бұрын

Your how to video will be a fine addition to my collection.

@hattemakern 3 жыл бұрын

Thank you for the tutorial 😊👍

@JackTheAwesomeKnot 3 жыл бұрын

Pro tip is to use an ACTUAL soldering iron, not that weird ass thing you got.

@mistirion4929 3 жыл бұрын

Or a soldering station with which you can vary the temperature

@justinellands7797 3 жыл бұрын

I prefer the electric pen style myself with the variable temperature. Not all solder is created equal.

@jonnyrock41 3 жыл бұрын

Yes ...get a 25 watt soldering pen..

@percaros 3 жыл бұрын

that's a soldering iron 🤨

@codedaily365 3 жыл бұрын

Lmao 😂😂😂yeah

@eosjoe565 3 жыл бұрын

Why use flux paste when using rosin core solder? I've been soldering electronics for over 50 years and the only time I find you need flux is when using acid core solder and joining copper pipes.

@walterbrunswick 3 жыл бұрын

there isn't enough to fully 'wet' the copper

@TheCarpenterUnion 3 жыл бұрын

There is no need. The only reason would be if you're trying to get the solder to penetrate further into the joint.

3 жыл бұрын

Extra flux can be a life safer imo. It makes some jobs much easier, although that's on pcbs in my experience.

@mckenziekeith7434 3 жыл бұрын

I like to add a bit of no-clean liquid flux. Solder wets out better. But it is not necessary.

@jbalazer 4 ай бұрын

Extra flux helps the solder flow and wet the wires. It especially helps when using lead-free solder.

@marcoscar.injecao_eletronica. 3 жыл бұрын

Eu tenho uma dessa, e é muito boa!!

@HiTechDiver 3 жыл бұрын

I personally use heat sinks to protect the insulation from melting, or especially if close to sensitive electronics, it protects them as well.

@unknowncuyler5449 3 жыл бұрын

i need to solder allot of wires. im trying to build an army! oh wait i need a soldier video.

@Krankie_V 3 жыл бұрын

Adhesive lined shrink tubing is far superior to applying silicone grease and using regular heat shrink. It's kinda expensive but it's worth buying the good stuff.

@frankammirati3385 3 жыл бұрын

Great video now to apply this to a real world repair on a vehicle . Video is great for demonstration on how to do it , I would love to see your methods when you have a word to repair in a place like under the dash or anywhere on a vehicle .

@luiscarlosmarques3946 3 жыл бұрын

Excelente work. Safe and clean. Tks.

@spicymchaggis2601 3 жыл бұрын

I always get a giggle when Americans say solder and aluminium 😆

@jessepaynter3752 3 жыл бұрын

How do you say solder?

@byf4ith 3 жыл бұрын

Probably pronounce it SOLD Errr

@Cola.Cube. 3 жыл бұрын

Aloominum. Lol

@crashalarm3283 3 жыл бұрын

In America it’s called aluminum not aluminium, in fact when I spell it that way it shows up with a squiggly red line to show that I spelled it wrong.

@PoKeKidMPK1 3 жыл бұрын

the original was to be set upon word was to be aluminum, apparently editors or some science thing decided to stick another i just because it goes with -ium. aluminum sounds way better and more consistent than Al U MiN EE uM. especially al/lumium which were the first thought of words when the metal was found before settling on aluminum and having it pointlessly changed to aluminium. solder isnt even with an l in older forms such as sou-der or -dure. unless you go all the way back to solid-are and solid-us. the british-english who often dwell on things to compensate for their lack of intelligence unlike those of them who probably paved the way for them, and are more productive, dont seem to get anywhere except to pointless problems.

@simonharris4873 2 жыл бұрын

Don't clean the iron before you put it away, leave it covered in solder to protect the tip. Dab a small amount of solder to the tip before you start, it will help transfer the heat. Clean the flux of before you put the silicon on. And most importantly, if you ever plan on removing this connection, then don't do anything you see here. Just tin each wire, then lay them side by side, and heat the solder to join them.

@gunterthir498 Жыл бұрын

Ich habe eine Wellerlötpistole die ist 40 Jahre alt und funktioniert noch immer. Tolle Qualität!!!!

@travisdelange3035 2 жыл бұрын

Thank you really helpful 🙏

@limestar9751 3 жыл бұрын

Went through 50 solder videos 2 months ago when trying to patch two light strips together - none of them covered everything as succinctly as this video.

@alanbrown7155 3 жыл бұрын

Grate video bud. Can you tell me when you doing a review of the finished leoch. Thanks.

@SilverCymbal 3 жыл бұрын

Unfortunately the one I received had shipping damage internally so I wasn't able to use it. I am working with them on a replacement.

@alanbrown7155 3 жыл бұрын

@@SilverCymbal ok bud thanks.

@alanbrown7155 3 жыл бұрын

@@SilverCymbal Did you get the one with the separate mppt controller that you plug in as well, you no, the one that hobotech got. If so, I have my own victron mppt controller but I need some information first like float charge equalization voltage & so on. If you could get that information from your external mppt controller they give you then I can use my own mppt controller instead of the junk they give you with it. If you don't mind that is. Lol

@squid0g 3 жыл бұрын

1 min in and already so many good tips. Thank you.

@michaelblair5146 3 жыл бұрын

You make it interesting yet you sound smart enough that I trust you implicitly

@rhobson 3 жыл бұрын

Some basic tips, but the chosen soldering iron definitely looks like it can get too hot for smaller wires. Always keep that in mind. Also, if you have enough wire to really solder properly, always go for the western union splice, AKA the one used by NASA standards. ;)

@tylercampbell3134 3 жыл бұрын

I thought the western union splice was more of a solid core thing?

@rhobson 3 жыл бұрын

@@tylercampbell3134 only partially, if you don't use solder. It has does a perfect connection with these strandedwires as well using solder. Only downside is the large wire area that becomes "stiff", but I never actually found that to be a problem, as I don't even try to attempt the western union splice if the wire isn't long enough due to lack of fine motor skill :(

@R4MP4G3RXD 3 жыл бұрын

Aka the lineman splice

@fully_retractable 3 жыл бұрын

The puddle on the iron transfers heat faster. Feed a puddle before holding against the wire, the puddle actually transfers the heat to the project, but if you're using this style of soldering gun, it's irrelevant because the surface area of the tip.

@Deerector Жыл бұрын

Great video. Thanks.

@AMS-1 3 жыл бұрын

Great vid thanks

@andrewpoloni4197 3 жыл бұрын

That's an *excellent* presentation; everything was included: tools, techniques, and operational concerns. Well done and thank you!

@jonmayer 3 жыл бұрын

Too bad the information in the video is incorrect.

@andrewpoloni4197 3 жыл бұрын

@@jonmayer Care to share how/why the information is incorrect?

@andrewpoloni4197 3 жыл бұрын

@@jonmayer Thanks for the troll sighting!

@ferebeefamily 3 жыл бұрын

Thank you for the video.

@arinasan247 2 жыл бұрын

Great video!

@christianjorgensen249 3 жыл бұрын

Another great video Mr Silver! I will follow your instruction to the T. You really should have your own DIY TV show, you’re very good at it!

@SilverCymbal 3 жыл бұрын

Thank you, you are very kind!

@Dexter_Solid 3 жыл бұрын

Dielectric grease is a waste of time, causes the shrink tube to slide off over time and prevent the glue from sealing, heating the wire from below puts too much heat in the wire and damages the insulation, its fine on small wires but larger ones will cause issues. Melt the solder over the wire with the iron and heat from below when theres more surface contact area to transfer heat in to the area instead of 6" down the conductor melting the insulation. Heating the entire wire also causes the solder to flow further down the wire causing the entire area to be come stiff, its also a giant waste of time. Ive soldered thousands of joints that lasted my entire career.

@UnyieldingSeraph 3 жыл бұрын

Thank you for pointing out the grease causing the tubing to slide off. Just get the tubing with the adhesive and problem solved no need for fancy grease

@douglasmueller4684 3 жыл бұрын

Thanks will try that today. Doing a throttle bidy 8plug replacement.

@ElektrischInkorrekt 3 жыл бұрын

Pro-Tip: use these heat shrink tubes with glue (they are a little bit shinier than the normal ones on the inside). They won't slide of and they're helping by making the Wire stiffer, so that the wire won't Break at the end of the solder Connection...

@leaftye 3 жыл бұрын

Or can work fine if a second longer heat shrink with adhesive is used over it.

@ElektrischInkorrekt 3 жыл бұрын

@@leaftye I often use different Layers of heat shrink tubes. In my cables are often two or more wires. So I am insulating the wires one by one and after that I will push one ore two Heat shrink tubes over THWe whole cable, so that the repaired Part is fully covered within these upper heat shrink tubes.

@artlife6210 Жыл бұрын

this technique is a must for boat wiring in saltwater!

@metalmotorcycles5732 Жыл бұрын

Thanks for this! I have to extend the control wires on my motorcycle and have never soldered before.

@user-xg1yl3wc7r 3 жыл бұрын

Синяя изолента заменит все эти понты

@politicalfoolishness7491 3 жыл бұрын

Your video is excellent. Just a couple of points. I prefer to keep the soldering gun above the work to avoid excess solder and flux running down the tip. Also, in electronics, especially fine connection work, I disagree with heat up the work first. The reason for this is you can damage components and melt insulation of wire. Instead what I've learned and practiced for decades is to get make sure the tip of the soldering tool is hot, and to apply the solder to the place where the tip meets the work, usually at the same time the tip touches the work. Because tips tend to be round and the work as in the case of wire is round, the actual contact area between the two is small and so heat transfer is slow. By applying the solder to the place where both contact, you use the solder itself to instantly expand the contact area instantly and heat transfer rate significantly. This seems to create much better results. If you try it you will see what I mean. FYI - the notion of heat the work first is still around but it's origins I believe are from things like plumbing and soldering tin, etc. Not the best for electrical from what I've experienced.

@Filmhome274 3 жыл бұрын

kzfaq.info/get/bejne/q9abeNVj3bHRhI0.html

@wickedgood1984 3 жыл бұрын

Great video. I prefer marine heat shrink. It has a waterproof material inside that melts when you heat it causing a waterproof seal without applying anything else. It’s just one less step.

@khancross 5 ай бұрын

I like the soldering, sealed absolutely great!

@justincase2281 3 жыл бұрын

Best short tutorial on soldering I've seen. ALL tutorials should be as clear and direct as this, regardless of the subject. Others should take a lesson from you!

@SilverCymbal 3 жыл бұрын

Wow, thanks! I really appreciate it

@justincase2281 3 жыл бұрын

@@SilverCymbal You got it. When something's good, it's good. And that should be acknowledged! Best - 👍

@limestar9751 3 жыл бұрын

Agreed.

@johnjordan6736 2 ай бұрын

🤡

@justincase2281 2 ай бұрын

@@johnjordan6736 You're saying I'm a clown? Right back at ya. If that's the case.

@snap-off5383 3 жыл бұрын

if you get the marine heat shrink, it has the goop inside it already. The purpose of flux is to break surface tension of liquid solder, but it really helps move the heat too, so I gob it on then alcohol it off afterward.

@shadowopsairman1583 3 жыл бұрын

Flux chemically cleans the wire