Nitro RC cars can be intimidating, but they don't have to be. In this video we show you how to start a nitro car step-by-step, and more importantly how to stop it. eurorc.com 5% off code: rc5 #nitrorc
Пікірлер: 32
@michaelinzitari10 ай бұрын
Nice overview for beginners. Preheating the engine will make it easier to start especially if new. Blocking the stinger to stop the engine does flood the engine but not if you open the fuel tank at the same time. Pinching the fuel line is a great way to stop it. Blocking air is even better but hard to accomplish if filter is zip tied on to carb. Stopping the flywheel always a great emergency way to stop. Great idea to carry an old rag with you at all times so you have multiple ways to stop the engine without burning yourself or losing skin
@alanlucas50110 ай бұрын
It's also very important to burn off any residual fuel that maybe in the engine by leaving the glow start in the engine and crank it over several times. Also make sure the piston is at bottom dead centre before storage. This will ensure the cylinder doesn't contract around the piston when cooled down. Also spray a dash of spray oil or after run into the cylinder and a dash of spray oil into the carburettor before storage.
@user-sk4wr3xk6c9 ай бұрын
Nice video for beginners. Thanks
@alanlucas50110 ай бұрын
I use a syringe to prime the fuel to the carburettor.
@BASSstarlet10 ай бұрын
Same here. Its more efficient and you can see the fuel running inside fuel lines.
@RCFPVSTL10 ай бұрын
Looks great!
@RazorRC10 ай бұрын
Thanks
@hondofourfivetwo934710 ай бұрын
Back before YT when I worked at my LHS I basically had this same talk with every new nitro car owner including help with the first startup, tips for breaking in the engine etc.
@RazorRC10 ай бұрын
That's great you helped so many people! That's kind of the reason I did this line of videos, just to help all new people to RC get started and be able to do the basics. Even if there's no LHS nearby.
@stevenzielinski72295 ай бұрын
11:53 You will NEVER hurt an idling engine by pinching off the fuel line. Actually, the preferred method of shutting the engine down AT THE CONCLUSION OF THE RUNNING SESSION is to run it up to normal operating temperature and while it’s hot and running along, pull the fuel line until it stops. Then, with the fuel line disconnected, make several attempts to start the engine until it no longer fires ( “pops” ). You must burn all residual fuel remaining inside the crankcase to avoid corrosion. Once it’s cooled, apply a quality after run product , a few drops in the carb and a few down the glow plug hole. Spin the engine over half a dozen times with the glow plug threaded in only a turn or two ( to avoid hydraulically locking the piston ). NOW the engine is ready to store until the next running session. Keep in mind , the next ( first ) cold start, the engine will be a little “ rich “ due to the after run oil. Once it’s running and warmed up, blip the throttle a few times to help clear out the excess oil. Oh, and remember to re - tighten the glow plug.
@brothertax10 ай бұрын
As someone who’s never driven a nitro this was super interesting.
@RazorRC10 ай бұрын
Glad you liked it!
@gomezleonardo607 ай бұрын
Awesome, I needed this as a NOOBIE
@Andries.Buskenz4 ай бұрын
Remember if it won't prime with fuel. Its usually a clogged carb highspeed needle! Not lack of compression.
@Andries.Buskenz4 ай бұрын
Really get to know the idle needle is my suggestion. Instead of throttle trim.
@meudrone4k36910 ай бұрын
Chique carro 🚙🔥💥💨😎🥰👍🏻💪🏼
@slimjim27263118 күн бұрын
I just bought one and clean the air filter and the base of the car. Now after everything is all dry up, I try to start it and the pull string is lock. What can be the cause of that?
@j-1lokes29410 ай бұрын
What is the difference with those engines and racing engines . I see that racing engine pre heat block up to 200 then they fire it up.
@felixculpa624010 ай бұрын
good video, I think I figured out the rubber nubby on the end of my tuning screwdriver is for pressing against the flywheel for shutdown
@RazorRC10 ай бұрын
Yup!
@toolbaggers10 ай бұрын
Method 4. Reduce idle on transmitter below stall RPM.
@RazorRC10 ай бұрын
That won't work unless your idle screw is set wrong and then you're going to stall every time you brake.
@vainparasite8 ай бұрын
I've no idea why but I've just tried to stop my nitro car by covering the exhaust pipe but it didn't stop. Any idea why it's started to do this? Cheers
@RazorRC8 ай бұрын
probably an air leak somewhere
@HL-OOI10 ай бұрын
Hate pull start back in the 2000s.. 😂 better get the starter box..
@toolbaggers10 ай бұрын
You like to lug around a starter box into the field or you just run your RC in comfy places?
@HL-OOI10 ай бұрын
@@toolbaggers on the track..
@Douger31810 ай бұрын
i siffen mine out of the tank so i don't waste it. expensive fuel
@user-jm6ps8rd4r4 ай бұрын
😢😢😢😢
@kiethpederson75583 ай бұрын
This guy is kind of sounds like Scott Disick from the Kardashians he must've got his inspiration from Bruce Jenner who love to fly RC helicopters however Bruce can't do that no more with the long fingernails
@JustinFromThe2063 ай бұрын
LOL Bruce can do it Caitlyn can't :)
@BASSstarlet10 ай бұрын
Another way to prime engine is to use a syringe. You could control the priming with a syringe better, i think.