This man and his videos have saved so so many LT50'S Thank you, Marty!
@Martysworkshop Жыл бұрын
I'm glad my videos can help. Thank you for watching and following the channel.
@lukehaymes42863 жыл бұрын
Hey thanks for this tip, I’ve finally got my quad running after months of not knowing why it kept cutting out after a few mins. I actually had the opposite of this problem, my float was set up in such a way that it was turning the fuel off prematurely and cutting the quad out. Stressed me for months and I’d kinda given up. I bent that float a little and it’s running like a dream so yeah thanks for the tip you really helped me.
@Martysworkshop3 жыл бұрын
Thank you for your feedback that certainly is a werd one fp luke. Glad you found it and I'm glad my video helped. Thank you again for watching
@stevehayes9003 жыл бұрын
These videos are great, I recently salvaged a perfectly good lt50 from a skip. Got it running and overnight emptied a full tank of petrol onto my garage floor 😆 know I know why! Looking forward to more videos in this series!
@Martysworkshop3 жыл бұрын
Thank you for watching i will have part 5 up soon.
@monisyed2394 Жыл бұрын
Brilliant instructions and explanation. I have the same problem on my daughters Quad was thinking it needs a service 😂 and was dreading it costing a bomb. Thanks much appreciated an easy fix your a champion have liked abd subscribed all the best. 👍🏽
@Martysworkshop Жыл бұрын
Glad my video could help
@NRNProductionsYT3 жыл бұрын
Thank u. This helped me fix my quad bike!!
@Martysworkshop3 жыл бұрын
Im glad it helped, thank you for watching
@conormcdade6021 Жыл бұрын
Hey mate can you point me in the right direction I purchased one yesterday off a fella all round very good condition except he said when storing it leave the fuel on, he said don’t turn it off cause when it gets turned off it leaked 🤯when it’s in the on position it’ll hold the fuel ok? Any idea
@Martysworkshop Жыл бұрын
Hello I coverd fuel taps in part 3 of this project, take a look in the description. All parts are listed. Thank you for watching
@solenebooker47893 жыл бұрын
Topman many thanks
@Martysworkshop3 жыл бұрын
Thank you for your support.
@FortWhenTea3 жыл бұрын
nice video man!
@Martysworkshop3 жыл бұрын
Thank you for all your suport
@jasonpettigrew1073 жыл бұрын
Awesome videos!! I just picked up an 86 lt50 that is missing the cylinder vacuum stem and plugged with a set-screw. Having a tough time getting it started without it in place. Searching I cannot find a replacement to re-add the stem back. Any tips where to search? Also, will you touch on the wiring harness and magneto? Thanks and looking forward to your upcoming videos on the complete tear down and re-build!!
@Martysworkshop3 жыл бұрын
I'm not sure if I'm honest i would like to think you could replace it even if you had to drill it out and just fit a standard fitting i will have to look into it. Sorry it took so long to reply.
@eliphino1210 ай бұрын
What is the port on top that doesn’t connect to a hose? It’s to the right of the fuel line
@Martysworkshop10 ай бұрын
It's just a vent there shuld be a pipe that comes off it and just hangs down behind the engine.
@stevesworld7831 Жыл бұрын
Hey Marty, I have a 08 suzuki DZ50, I cleaned the carb and replaced the spark plug. Im having trouble getting full RPM. It feels like the rev limiter is going off. Is there a way to adjust it?
@Martysworkshop Жыл бұрын
I'm not familiar with that engine sorry
@jonathanayers55403 жыл бұрын
Do you have any videos of installing a piston and ring's in the LT50?
@Martysworkshop3 жыл бұрын
Not yet sorry but it is on my list of things to do
@seendizle3 жыл бұрын
my jr50 I had this problem. Bent the tab and fixed the problem. However when I lean it over to the right (the side the carbs on) the engine cuts out. What's causing this??
@Martysworkshop3 жыл бұрын
Have you tried bending it back slightly? The fuel level might be too low in the bowel know causing it to suck up air when you lean it over.i hope this helps.
@seendizle3 жыл бұрын
@@Martysworkshop yea i just did the float broke off the metal tab. Darn it. Super glue to the rescue. Just ordered a new float. It also blows alot of smoke and has oil coming out the exhaust. Does this mean the rh crank seal is gone???
@Martysworkshop3 жыл бұрын
Yes i would say so how much oil do you mix with the fuel? Or does it run off the tank?
@seendizle3 жыл бұрын
@@Martysworkshop it runs off the tank.
@Martysworkshop3 жыл бұрын
Just checking you would be surprised how many people pre mix and put way too much oil in, yes i would agree with you and go for that seal, thank you for watching.
@richmead95693 жыл бұрын
Excellent videos, thumbs up from me! Any of you guy's point me in the right direction for a 1995 workshop manual? 👍
@Martysworkshop3 жыл бұрын
Try this one www.crservice.dk/Suzuki ATV/LT50/LT50.htm
@joeyd47083 жыл бұрын
Would this problem also cause quad goin bad flooding etc
@Martysworkshop3 жыл бұрын
Just a leak from this I'm afraid, i would check your jets or mixture settings i have done a 2 part video on carb clean and setup if you want more info. Thank you for watching
@bladelad37973 жыл бұрын
What's the valve just left of the clamp mate
@Martysworkshop3 жыл бұрын
The mixture screw is just to the left of the clamp, and thank you for watching