www.powerbookmedic.com - This video will show you how to take apart the DJI Phantom 3 Standard Drone
Пікірлер: 43
@sndrpmedia8858 жыл бұрын
Thanks a lot! Finally a video, showing a standard model, and not the professional or advanced :-)
@aquaspark1able4 жыл бұрын
Thank you at last a standard phantom 3 take down, finally I can identify all the components, and undo some of the mods done to mine by the previous owner
@sleeptyper4 жыл бұрын
What mods it had?
@stephenwood40536 ай бұрын
I like this. Two questions answered that were bugging me. One was what is the white cable in the leg and what size torque screws. Thanks for telling me about the compass chip.
@Bobster9868 жыл бұрын
Nice video but, I have found that cutting the front arm stickers along the line where the two part of the shell come together is better then pulling the tape away and ruining them completely. Happy flying!
@TheGoodStink12 жыл бұрын
Helping me fix my drone in 2022!
@Rafoam8 жыл бұрын
Thank you so much for this video!!! I was scared of doing this without proper guidance!
@having1a1laugh5 жыл бұрын
Great video thanks, very precise. I've shunted my 3 std twice now and both times the antenna cables (grey and black have been cut) the first time the camera came off (no secure pins) then last time hit a tree while going backwards!!! I now am a believer of "if you can't see it" don't fly? Just hold where you are and walk to drone? I use small ty raps to thread through where the pins go. I don't know how I didn't silicone the grey and black cables to the body, which I promised myself I would do after the 1st shunt but its a must to eliminate loose cables? Hope this helps others?
@shortribs117 жыл бұрын
Awesome video, thanks for sharing.
@truckingpix4 жыл бұрын
thank you!! you have the best guide on here
@PowerbookMedic4 жыл бұрын
Dudderz Thanks! Happy we could help!
@golddredging6 жыл бұрын
Where can I find the tool you are using to pry the shell apart with? Thanks for making a very informative video
@TommyGames978 жыл бұрын
If I take off the black and gray wire on the gimbal and add a bigger arial would it still work ?
@fer19808 жыл бұрын
This is great! thank you very much, I wanted to replace the 2.8ghz antenas and had No idea how.
@JEFF2010SSRS7 жыл бұрын
Thanks Much ! Great Job .
@philg67578 жыл бұрын
Thank you very helpful.
@bhavinnagda24837 жыл бұрын
great video
@samsamara59375 жыл бұрын
well done mate.... thanks
@jayrobertsager25367 жыл бұрын
You were not concerned about having a magnet so close to your compass module? I ruined my Hubsan501s that way, easy fix to replace the compass module but I was grounded from flying for two weeks while I waited for the new part. Love the video and I appreciate your good work but I was just concerned about the magnet. Cheers.
@JKTCreation7 жыл бұрын
Good job. By the way, what's the music name?
@technologylover91837 жыл бұрын
Wow you did an excellent job on this video. Thanks.
@solentlifeuk7 жыл бұрын
To remove Drop PIns is much easier and no need to pry off with screwdriver. Press them full on and then wiggle them back - you can even re-use after ... There are plenty vids on YT showing this.
@rmendesjr7 жыл бұрын
Up
@hemsmar5 жыл бұрын
"once the upper case is free, maneuver it so that..." This is the riskiest move and it shows for just a few seconds. Be very careful with this and take your time. Press on the lower shell in the middle curves until you hear a click and then rotate to the next and continue until you have it free. If you force it, you will break it or wires underneath. Also, when putting back together, you should use blue lock tite on two screws near the motors.
@clautamiralves7124 жыл бұрын
Hi. I have a vision 2 that don't wanna fly anymore. I am willing to use as a camera only. If I remove the motors and the lights will it turn on the camera afterwards?
@PowerbookMedic4 жыл бұрын
Clautamir Alves We have never experimented with that before, so we aren’t sure. Let us know if it works out!
@_connic8 жыл бұрын
Just to make it clear.. The two antennas on the legs are for transmition and you can unplug them after opening the shell? Also, the video transmitter and antennas are built in the gimbal? So to change video antennas i should only play with gimbal? Thanks! Please answer ASAP!!!
@Bilal-fi9ev8 жыл бұрын
+iHacker007 no the antennas are not on gimbal. This guy is very unexperienced. You can let the antenna connected to board if you replace the shell. IF you replace the board then you need to unplug all of them and desolder the motors and leds.. The antennas for the video is in the battery compartment. the two things looks like square, where the black and gray cable goes to.
@_connic8 жыл бұрын
I am inexperienced with drones, yes. But i know a lot about antennas. And yes the video antennas are in the battery compartment, but the VIDEO TRANSMITTER and the antenna plugs are inside the gimbal.
@MrEdmundoGC8 жыл бұрын
+iHacker007 all i know, you can replace the antennas, the squares ones are 2.4ghz! and the one in the legs are 5.8ghz!
@CaptainPhoton648 жыл бұрын
what are the black and grey wires used for on the gimbal sir
@PowerbookMedic8 жыл бұрын
+Ricky ThePhoton Dexter - I believe you are referring to the wireless cables.
@CaptainPhoton648 жыл бұрын
+Powerbook Medic I had a crash and the grey wire cap came off and since its coaxial I probably cant mate it back to the wire..so I have to replace antenna inside battery bay which means taking it apart
@davidpeck33207 жыл бұрын
Ricky ThePhoton Dexter j
@christianfink41664 жыл бұрын
What soldering iron are you using?
@PowerbookMedic4 жыл бұрын
We recommend this sodlering station: amzn.to/2Km5pSE
@scottjanssen656 жыл бұрын
Great video, but I wish you'd spent more time around 10:00, showing how to undo the clips that hold the two halves of the body together.
@tyeb677 жыл бұрын
BONJOUR VOUS VENDEZ CARTE MERE DJI PHANTOM 3 STANDARD