HOW TO TEST IGNITION COIL WITH A MULTIMETER AND NOT KNOWING THE SPECIFICATION

Рет қаралды 26,643

Top 5 Auto Repairs

7 ай бұрын

How to test ignition coil with a multimeter and not knowing the specification.
Top5autorepairs

Пікірлер: 25

@Andrew-rb4gs 7 ай бұрын

That method saves alot of guess work for us DIY guys. Thanks. Greetings from Toronto.

@adr8nalin73 Ай бұрын

Thanks Quick and easy video

@j233333 3 ай бұрын

Hats off! I just saved few hundred $$!!

@buckjohnson6656 6 ай бұрын

Man that's so much easier 👍 thanks

@dyksyn2823 3 ай бұрын

Thank you so much for the education. I have a 2008 honda accord 2.4L is it the same coil spec

@afzaalkhan.m 4 ай бұрын

Good video .thank you

@23thebull 26 күн бұрын

Just subscribed awesome video

@limamantapachitas 2 ай бұрын

thanks master!

@dyksyn2823 3 ай бұрын

Please help with 2008 honda accord 2.4L coil resistance spec. Thank you

@SummerEazelivin 2 ай бұрын

I was hoping you would compare to a faulty coil.

@jf8322 4 ай бұрын

So what was the misfire caused by on the k24 you were working on

@craigcraigster4999 7 ай бұрын

Thank you for this invaluable information. Question: how much of a difference in ohm readings between old and new coils (if any) indicates replacing the old coil(s) for brand new coil(s)?

@Top5AutoRepairs 7 ай бұрын

It will vary between each vehicle. All Data is a good software to confirm specifications.

@craigcraigster4999 7 ай бұрын

@@Top5AutoRepairs Thanks!

@viewlesswind 7 ай бұрын

The rubber underneath the top part on one my car's coils has some cracks. Do the cracks impact the car at all? Thanks.

@Top5AutoRepairs 7 ай бұрын

It will cause voltage leaks. You may notice an engine misfire, poor gas mileage, hard start, maybe no start, poor engine performance etc...

@viewlesswind 7 ай бұрын

@@Top5AutoRepairs the cracks are not in the rubber that mates the sparkplug though. It's the rubber on the top part that mates the valve cover. And that can cause the issues you just described?

@Top5AutoRepairs 7 ай бұрын

It shouldn't be an issue

@aleksandarkocovski6939 Ай бұрын

How about measure on ignition coil with 4 pins?

@owens417 4 ай бұрын

How do you check a 4 pin coil? Would it be the same?

@Dominic-yu1ez 4 ай бұрын

That would have 6 testing combinations instead of 3

@jdmfamily7182 3 ай бұрын

Are all the coils suppose to have that same reading? 00.4 00.4 0000?

@TheTomppaa 3 ай бұрын

I don’t think so. For example mine brand new are 0,08 ohms.

@A.C.71 4 ай бұрын

I would like to point out something. My mechanic, who is a truly phenomenal told me ohming out a coilpack is not a 100% way to determine if a coilpack is good as he has had many coilpacks ohm out perfect but still fail under a load. So this test is just for a chance at showing a defective coilpack but not to know for 100%. Oem coil (motocraft DG511,DG508) ohms should be 0.55 ohms for primary circuit and 5,500 ohms for the secondary.