Excellent knowledge. I'm diagnosing a Fisher-Paykel throwing an RPS sensor fault.

Indeed helpful. I will certainly use this on certain errors. You can probably use a 9 volt battery to power the sensor on the field.

Knowing what should be at each pin is most of the problem - not sure if there’s a place to find that information??? This was extremely helpful. Thank you!

Great vid. It's thank to you and others like you that make KZfaq such a great place for info/help. Thanks again.

You video was instrumental to diagnose my LG hall sensor malfunction and repair. Thank you so very much!

Simple and easy to follow troubleshooting

Great Video, a big thank you. Le error on my machine led to a faulty sensor with your guidance. Fitted a new one and all is well. Thanks again.

Question, can the sensor accept more than 10 volts? Can the voltage be from 10 to 15 volts? Will that voltage damage it?

I found 5 to 1= 10.36 5 to 2= 19 5 to 4= 20 4 to 1 = 10 4 to 2 = 00 I already ordered, the patrt, ends 2002 A The washer ,..do not give codes, starts like spinning, and water pump, on and on, Thank you , waiting for the part GRACIAS, GRACIAS,

Thank You! Thumbs Up

Thanks for the video. Mine just like part sample #1 open 5 to 2. Done. part ordered thank you for your help

Excellent Video! Thanks!

I'm repurposing a drive motor for another use. My BLDC controller (manual is in Chinese) has H+, H-, HU, Hv, HW for hall sensor input. Can I use the factory hall sensor for my controller or do I need 3 separate sensors? I have sensors if need be, but the factory sensor would be a cleaner looking install. How would you recommend wiring up the factory sensor?

Thanks sir we'll like you channel sir

Very helpful, thank you, I'm gonna connect mine to the power supply and test it,, because i dont get 10K ohms between 2 and 5 so most likely bad

Hi I have a washing machine 7.5kg Fisher & Paykel top loader, I can hold the agitator with my hands when its going and stop it from moving the motor has no torque would a rotor position sensor cause this? any help would be appreciated. Good video

Thank you for this Video, especially the Test part, I tested my LG sensor with the Voltmeter, the readings are OK, but the Washing Machine still cannot spin. Can I have a faulty sensor with correct readings???

It is not clear unless I missed something. To start with before you approached the hall with the magnet, obviously it showed voltage ( rooughly 10 volts). Then when you approached the magnet against the hall, it erased the voltage. This is meaningless. By default there should be no voltage to my understanding. It is the presence of the magnet that should separate the charges in the sensor and cause voltage to appear. And up on second approach it should erase it. So there are three states or so it appears. 1. No magnet present ( should imply off state) Because there can only be two states. Either off or on. 2. magnet present ( on state) 3. Magnet present again. return the hall back to the first state ( off state)

Great video man but have a question i want to use the inverter direct drive motor in on /off way not on washing machine do i need to use the hall sensor and why they use the hall sensor in the DD motor?

Sooo useful video, thanks man!

What is the volt goes to stator after controller

I got 0 and 10V from pin 1 but 0 and 8V from pin 2, hope replacing it will solve the fault.

I appreciated your electrical test, TKS i was looking for that! Good Info!

Great video man!

I will try the 9 v Battery, and themagnet, voltimeter

What are the symptoms of a faulty sensor?

And to test the bad part, what will the reading show? you tested a new one correct & do i need a power supply to test it? I get OL with the new & old part.

Loved this video, but I have W10178988 part, do you know which pins to test on that one and what numbers I should get?

channel Bertzservice youtube Brazil

What are the symptoms of a faulty position sensor on the washer?

Thanks. Very helpful.

Thanks sir

Do we see same hall effect change for pin 3 as we see for pin 1 & 2 ??

exellent! so thats called sensor, i just exploded the part of the motor and do know what this pin things do

What are you swiping and bumping with?

is this method work with samsung washing machine?

Do you have more videos ?

I hate two questions why is only 10 VDC? And your power supply could be set to both A/C and D/C ?

i have a samsung with 4 connector why is it only two hall and not three isnt it a three phase motor so what trigger the third one?

where did you get the power supply

Max

Do we see same hall effect change for pin 3 as we see for pin 1 & 2 ??