how to test and replace hall sensor/LG washing machine motor speed sensor

Рет қаралды 72,301

Жыл бұрын

This video shows you how to Test and replace Hall sensor or motor speed sensor just in short period of time,using hand tools like digital multimeter
Screw driver, M17 wrench spanner , M10 T handle wrench,
for more videos like this please subscribe, like and share,
Subscribe and get a quick notification once we upload a new video
Thank you.

Пікірлер: 55

@Crazy_Dave 23 күн бұрын

Thank you, I now know what's wrong with my LG machine.

@felixtechnoaid2044 22 күн бұрын

A great thanks to me is when you share and you subscribe to my channel, do it it today enjoy more videos.

@jsbuckner 7 ай бұрын

This video helped me diagnose and replace only the sensor as opposed to the stator. The sensor cost me $8 and about an hours worth of time. The stator was going to cost $125 or up to $200 dollars depending on where I purchased it. I liked and subscribed. Th al you again!

@felixtechnoaid2044 7 ай бұрын

thank you so much, like and share❤️❤️

@capeman10 Ай бұрын

You are very kind to share your knowledge with others, may you be blessed always.

@felixtechnoaid2044 Ай бұрын

Thank you so much❤️

@Compwib 7 ай бұрын

Very well explained

@felixtechnoaid2044 7 ай бұрын

❤️❤️subscribe, like and share, you can also watch other videos from this channel, thanks.

@juslookin3 18 күн бұрын

What was the problem with the washer? Why would you suspect and test the sensor?

@rolanddejesus8685 Жыл бұрын

thanks very for sharing sir,God bless.

@felixtechnoaid2044 10 ай бұрын

thank you so much, we are here for you❤️❤️

@user-uc3hh9gr7b 4 ай бұрын

Thanks alot.

@DarkMoon3693 Жыл бұрын

Thank you! Your video helped me fix mine ❤🙂

@felixtechnoaid2044 Жыл бұрын

if you it helped you out keep sharing

@sachinkumar-qp4bo 9 ай бұрын

Thanks for hall sensor check ✅✅✅✅✅

@felixtechnoaid2044 9 ай бұрын

❤️subscribe, like and share

@carloscamsaparelhos 6 ай бұрын

inscrito no seu canal , parabéns pelo video , forte abraço

@felixtechnoaid2044 6 ай бұрын

❤️❤️

@shahidabbas5830 9 ай бұрын

Good one

@felixtechnoaid2044 9 ай бұрын

thank you❤️ subscribe, like and share

@felixtechnoaid2044 9 ай бұрын

remember to subscribe, like and share.

@MrTx2 Жыл бұрын

The problem in this hallsensors is the small 680 ohm surface mounted resistors under the grey silicon. They are easy to measure if you have patience to remove the silicone. These resistors is two 680 ohm in parallell for each hallsensor. If you have a potentiometer you can solder it in parallell with the burnt reistors and calibrate it to 340ohm. That works 10 out of 10 times and is great if you dont have the sparepart.

@felixtechnoaid2044 Жыл бұрын

this video is inspiring , keep sharing

@brainimplants Жыл бұрын

You got it! My board had those reading in megohms but I butchered it figuring it out. I got a replacement board from a scrapped washer and it also had 3 bad resistors. (A whole washer tossed for a few cents in parts what a shame.) I replaced the resistors and the washer motor is working normally. FYI the capacitors measure 120 nf in case someone butchers them removing the silicone.

@slingshot909 Жыл бұрын

your video did help me diagnose a bad hall sensor, but why do you put red lead into the common, why not blue, where im from red is power or hot +, blue or black is common

@felixtechnoaid2044 Жыл бұрын

if it did helped you , like this video and share❤️

@adi_1o1 Жыл бұрын

Resistances are independent of polarity.

@brainimplants Жыл бұрын

pin 1 is +12vdc, pin 2 GND, pin4 is hall b (end of board), pin 5 is hall a (middle of board). voltages on pin 4,5 are about 0.5v / 12v if you flip a magnet around them.

@70Naeblis Ай бұрын

I am reading around 7-9 ohms is that bad?

@evtjerkz425 27 күн бұрын

Mine lg doesnt have a sensor on the stator like this video any idea what it could be thats wrong

@felixtechnoaid2044 26 күн бұрын

Check IPM ic on main board, suspect main board failure

@lagzdinalagzdina3658 10 ай бұрын

Can something cause the motor to cause resistance? Meaning if the power is off the drums spins freely and when the power is on immediately becomes hard to spin and creates resistance. Won't go in full spin cycle stuck on 12 mins! The motor doesn't have the sensor on it like in most videos!

@felixtechnoaid2044 10 ай бұрын

is it LG

@tomkinniburgh9339 Жыл бұрын

I’ve replace sensor and now I’ve got no water. It spins but the water won’t fill. The water is on. What do you think it might be ?

@felixtechnoaid2044 Жыл бұрын

you have to check air chamber , hose, and pressure sensor, water valve .

@mohdfaheee1244 Жыл бұрын

This use spaner number??

@felixtechnoaid2044 Жыл бұрын

17mm spaner

@parshottambhaipandya9064 Жыл бұрын

LG 5.5 kg dayrek spin me nahi jata avaj aata he

@felixtechnoaid2044 Жыл бұрын

you can try English

@vipulbakade7764 11 ай бұрын

Sir, sensor no. 6501kw2001b and 6501kw2001a is different or is it the same, whether they can be replaced with each other

@felixtechnoaid2044 11 ай бұрын

one can work in place of other, no problem dear friend

@vipulbakade7764 11 ай бұрын

@@felixtechnoaid2044 thanks sir

@felixtechnoaid2044 11 ай бұрын

@@vipulbakade7764 likewise❤️

@aaroncanizales7840 Жыл бұрын

There's a problem with humidity.

@felixtechnoaid2044 10 ай бұрын

it was not humidity, it's oil leakage, oil seal and bearings are faulty

@stumpynubs5387 9 ай бұрын

What causes the sensor to go bad?

@felixtechnoaid2044 9 ай бұрын

truly me too I don't know why it goes bad,if I get some thing new on this I shall ret you know

@joexminion 3 ай бұрын

Anyone helpppppp. I replaced the sensor but still getting the le error. The drum is locked up. It tries to turn it but gets stuck. If I try and force the drum to rotor it sounds real grindy

@joexminion 3 ай бұрын

Ah. Broken magnet on the rotor cover that has to be it!

@70Naeblis Ай бұрын

I just replaced my hub tub and the main gear drive shaft, the gears were worn down and making terrible grinder noises, should of bought a new washer.. now it's giving me the LE error