Another valuable episode, and GREAT companion to the DVD. Thanks.

Thank you very much. This will help me a lot. I was not aware for 90 degrees left or right.

Just discovered you. Your videos are so well done and Have already been so helpful in building my Sport Performance Panther. Keep up the great work. I’m going to keep watching

You are one of the best I have seen to explain things.

Dear HomebuiltHELP, I wanted to say that I love your videos. This one was as usual very helpful.

Great video....really appreciate the 90 degree rule!

Great information as always, Jon!

Very Nice Video , I also was not aware of the 90 degree L/R +/- 1" problem with the torque wrench.

Another great video. Loved the 90° tip

Never knew the name of that tool, just ordered a set! Thank you!

Thank you so much for your great video.

Great information! Thanks!

Excellent advice, thanks!

Excellent video

Great video, very useful. keep it up.

this is super helpful, thank you. I'd like to see a manual to to torque in those AN elbows, keeping to torque values but also achiving the right orientation.

Good one Jon. Thanks. "Now everyone, back to building!"

Thank you

Good morning everybody , thanks sir for this crucial information

I found my kit included 6061T6 tubing for hydraulic, brake and fuel lines. Also if the tubing connects to the fitting at any amount of angle and not straight into it, it will leak. Small amounts of misalignment you can sometimes stop leaks with del seals.

Very helpful!

Good morning sir , beautiful and useful

The torque wrench depicted has a stamp or sticker that says it's calibrated and tested. Does Tekton do this or a third party? The inch pound torque wrenches from Tekton are 1/4 inch drive, crows feet generally are 3/8 inch drive. I assume a 1/4 - 3/8 adapter was used?

What if you used an extension on the 90° rule?? Would it still be close enough?? By extension ,, I mean length,, like a dog bone, not a normal extension of the torque wrench.. Thanks

Should -06 fuel line nuts be lockwired to prevent loosening from vibration??????

Very detailed instructions ,better then some A & P instructor . Thank you for sharing .. Normally should I back it off and re torque it again?.🐒

I want to know about your tires. Can you tell us about the Turf Glide tires?

good tips, BUT you can use the Torque wrench at this extension, mechanics do, they just find the torque reduction factor ( X 0.9 etc.) that the wrench maker has in the instructions with the wrench, then apply this factor to the target torque, eg: if you double the length you halve the torque, x 0.5 so if 500 ft/lb was called for you set 500 X 0.5 = 250 ft/lb on the wrench, this gets you where you need to be. this is used on gearbox adjusters, etc. where the room to swing the wrench is limited; only for emergencies, NOT for general practice, in normal bolting applications you use an appropriate sized Torque wrench for the job! ( there are special extension spanners for this purpose, their instructions also tell you what the correct setting for the wrench should be).

Can you tell me the product details

Can you use 6061 tubing?

WOULD YOU TELL US WHAT SIZE ALUMINUM TUBING IS USED WITH WHAT SIZE AN FITTINGS PLEASE

Great video. Most of us just tighten until it cracks then back off a turn. Lol

How about güt and tight?

Why or what is the origination of the name crows foot

10:01 that is the wrong torque setting for 3003?

Maybe don't bend the aluminium tube by hand like in the video, I'd use a bending spring or a set of pipe benders over the tube.far less chance of kinks and The bends come out a lot neater. I'm a plumber, I bend pipes all day. I haven't built my plane yet I've purchased all of your videos on the CH 650 so I may be wrong, just my opinion, let me know. Great videos you guys put out.

I’m an aircraft maintenance engineer and I find a lot of engineers lame and Ame engineers over torque everything and one of my pet hates is people that over torque screws and use very long screws to put panels on and when we had hangar meetings I would bring this up all the time and would explain that if screw are to long they can hit control cables, wiring and other bits ant this was a problem with a Metroliner we’re the factory at build used a very long PK screw to hold a panel which went through a wiring loom and the aircraft would activate the auto feather on and off till one day the aircraft just rotated and the auto feather activated at full power feathering the prop just off the ground and the pilot was selecting gear up at the time and mealy lost the aircraft he landed safety and it took several days to find the problem. I surgery that if you are not sure read up on it and do not overtighten screws in an anchor nut as you stretch the anchor nut and it looses it grip on the screw and the screw will fall out just nip it and do not use long screws unless the dragon requires it 1 to 2 threads pass the end of the anchor nut is all required to hold the panel in place safely also if you over tighten it someone has to try and remove it or it will break and than that is how you end up with scratches in the paint work or holes in the skin if you don’t know what you are doing so as I say if you are not sure be a good builder and do the smart thing read up on it and ask someone that knows about these thing also over torquing my damage components and this can cause them to fail further down the line so if it calls for a torque even if it doesn’t fell tight enough the torque is there for a reason and if you are not sure ring the makers

tighten until it breaks then back off a quarter turn lol

Sorry but the 90 degree method is not correct. The torque arm provided by the crows foot would be the same torque arm no matter the angle. This is because the length of the torque arm from the point of application (drive head 1/4, 3/8, 1/2) of the torque would be the same no matter. Your setting on the torque wrench is only accurate to the drive head center. This is why smaller torque wrenches can be used to tighten nuts or bolts beyond their range limit using a torque multiplier. This essentially adds a known torque arm extension to the drive head. The torque multiplier will then give you a multiplier for your setting on the torque wrench that provides the actual torque provided at the end of the extension (torque multiplier).

You tighten until it's tight then stop.

I found that a lot of engineers in aviation with installing screws bolts and other fittings they tighten them to tight especial screws holding panels on they use screws to long and over tighten the screws and this destroys the anchor nut over time and streaches the screw threads and when you go to replace the panel you have to change the screws and the anchor nuts and I show them take the screws till it bottoms and just nip maybe a 1,/8 of a turn the acchor nut will hold it and when putting panels on short screws as I have seen cables snap from long screws and bolt if you are not sure of read the manual