How to unassembling and lubrication your freewheel in 5minutes!

How to unassembling and lubrication your freewheel in 5minutes! | SHIMANO 7 Speed

Рет қаралды 25,798

3 жыл бұрын

Quick video, how to unassembly and lubrication freewheel. Replacement of the lubricant with a new one.
Replacement and addition of new bearing balls! New good quality grease and its working like a new 😁
#freewheel #freehub #unassembly #replacement #repair
PROCESS:
Unassembly
Clean up
Lubrication
Assembly
Restore your parts to their former glory!
Feel free to watch and subscribe to the channel.
Invite! also on the instragram to stay up to date!
/ rowerowe_drugie_zycie
Tools used to make:
IPHONE 7: Videos / Photos
INSHOT APP: video / photo / thumbnail editing
Music ❤️: Interlude
Musician: Silicon Estate

Пікірлер: 50

@jamesedmerdelacruz9478 2 жыл бұрын

it is recommended by the manufacturers to leave a gap on the bearing, basically remove at least 1-2 bearings on the bottom and 2-3 on the top, to give a free coasting without any bearing collision. Notice on the end, the freewheel moves like it's stuck it should move smoothly.

@Aku-mia Жыл бұрын

If that is true, does it mean that manufacturers sometimes put in too many bearings when they sell them?

@BlueTrane2028 10 ай бұрын

If you're going from a caged loose ball setup to balls without a cage, then yes, you fill the bearing completly and then remove one. Like for like? Same number as was there...

@jtnoodle 8 ай бұрын

LoL remove bearings? It doesn't yet spin freely because it's been freshly greased. Your advice is terrible

@chrishayes5755 7 ай бұрын

It's recommended by manufacturers to not put the bearings back in after disassembly. These aren't really meant to be serviced so don't try to put the ball bearings back in. If you watch towards the end you'll notice the freewheel doesn't move well. What he should have done is just put some mustard instead of the bearings and seal it up. Sounds silly but that's what Shimano recommends, I know the CEO personally he's a good friend and he told me that.

@darkmattersolo2137 5 ай бұрын

@@jtnoodleagreed 😊

@steelisreal4313 Жыл бұрын

@1:27 Beginners should use two tubs...One tub for upper bearings and one tub for lower bearings...That way u know how many bearings per area...

@BlueTrane2028 10 ай бұрын

Good idea. Just did that and it worked a treat.

@jjmcwill1881 9 ай бұрын

Explain

@steelisreal4313 9 ай бұрын

@@jjmcwill1881 the amount of bearings on the top race is always different from bottom race. If u put top bearings in a separate container than u will know how many goes back into top race during reassembly otherwise u are just guessing. It probably doesn't really matter but sometimes I'm OCD lol

@SirNickettyNox 10 күн бұрын

Also, I think the upper and lower bearings would wear differently so important to keep them separate, don't mix them up together.

@erickauffmann_official Жыл бұрын

Nice! Thanks for the video

@lonerbikes Жыл бұрын

Glad to hear it Thanks 🙂

@dennismolina2339 Жыл бұрын

Ferfect video!

@lonerbikes Жыл бұрын

Thanks bro

@tomaszjaocha7220 3 жыл бұрын

amazing

@MuftakisWorld 3 жыл бұрын

I have mf-tz21 could you plz tell me how many balls should put on top & bottom?

@munindradas8302 2 жыл бұрын

Very useful vdo.

@lonerbikes 2 жыл бұрын

Thx very good beo

@user-mz3qr7kz1o 3 жыл бұрын

Nice

@lonerbikes 3 жыл бұрын

Thanks 😊

@ivanta6283 Ай бұрын

whats the white thing? il the red is grease but whats the white

@nguyenanh-ki9sr 5 ай бұрын

❤❤❤👍👍👍

@chtimpeng 11 күн бұрын

I have a similar shimano freewheel and the hub is very stuck, where I can get that tweezer like tool and the socket to do the job? Thanks.

@chtimpeng 11 күн бұрын

the only thing I see on the freewheel is Suntour - Japan and it is a 7 speed. The bicycle is very old and been sitting inside the garage for about 10 years and I been riding it for the past 4-5 years.

@steelisreal4313 9 ай бұрын

Do u have a video for Shimano MF-HG20 freewheel total teardown? I want to remove the lockring in order to remove all the cogs individually and clean. The tool is next to impossible to find, thank u

@chrishayes5755 7 ай бұрын

not sure what model that is but it can either be locked by the smallest cog (threaded) in that case use 2 chain tools, or if it's got a locking ring use either a screwdriver and whack that shit with a hammer or use retaining ring pliers depending on the style.

@peterhaas5428 Ай бұрын

Does somebody know, what size steel balls are used in the MF Z012 freehub? And How many on Top and Bottom (as asked in another commend already) Thanks PS: Thanks for the nice and very usefull video :)

@lonerbikes 12 күн бұрын

enjoy !

@riderbros8032 3 жыл бұрын

tq bhai

@lonerbikes 3 жыл бұрын

Lasputev mierta

@Cbych Ай бұрын

Według mnie nie powinno się mieszać smarów w tak bliskiej i otwartej odległości. Ja bym dał ten łożyskowy na te trybiki i z bani, bo akurat dzisiaj też rozbierałem wolnobieg i smar z dolnej i górnej części przeskoczył. Tzn. przy skręcaniu wolnobiegu nadmiar idzie bokiem nakrętką i przy okazji na te trybiki.

@lonerbikes 12 күн бұрын

zgadzam sie ze smaru jest troche za dużo, ale mimo wszystko zostaje przy roznych smarach na bieznie i zapadki

@piotrmacc8793 9 күн бұрын

@@lonerbikes A możesz powiedzieć jakie to smary (ten czerwony i biały) oraz czym myłeś te elementy - dzięki.

@milindasenarath Жыл бұрын

my freewheel completely gone silent after a service. now i dont hear any click. is that a problem ? bike rides fine

@pr00009 Жыл бұрын

the soft brag is not soft at all bro

@imrevadasz1086 10 ай бұрын

You probably got too much grease onto the freewheel pawls. You should only put very thin grease on those, or even oil. With grease on the pawls you risk that they might start sticking. So it's not breaking anything, but your freewheel might spontaneously stop working properly, until you fix that issue. In the video you can see that a different paste was used on the pawls, vs. the grease used for the bearings.

@GlennMarshallRocks 3 жыл бұрын

What were you using for lubricants...? Do they remain on the surfaces long term (i.e. years) or do you need to relube the cassette periodically....?

@lonerbikes 3 жыл бұрын

I use normal expensive good quality lube for bearings, if everything is fine you don’t need periodically service, but however riding in difficult conditions should be done once a year vmbefore the season

@GlennMarshallRocks 3 жыл бұрын

@@lonerbikes - and what do you consider to be "normal expensive good quality lube for bearings". You use two lubes in the video, one white, one red. What are they...? Who makes them...? .

@lonerbikes 3 жыл бұрын

@@GlennMarshallRocks bearings lube and shimano freehub grease

@GlennMarshallRocks 3 жыл бұрын

@@lonerbikes - Great... Thank You... ;-)

@johnsandoval347 3 жыл бұрын

Loose Balls Rule...

@kenbad8271 2 жыл бұрын

Not as easy to do as you show it especially in older one they don't screw off that easy they get stuck and they're very hard to get off

@lonerbikes 2 жыл бұрын

You have right, in older freewheels, dirty with rust when stay in outside long time is rly hard to get of, for the purposes of the film, I loosened the cap earlier, you can use a punch and a hammer, it is shown in my other film, Regards