How to use DEFU 368A manual cutting machine Laser cut key HON66 Honda Civic

Рет қаралды 716,523

2 жыл бұрын

Key was purchased on amazon
I already programmed the key to the car to it’s immobilizer.
Using DEFU 368a
Please support me by donating so i can keep making great content.
Paypal: autopurlieu@gmail.com
Cashapp: $AutoPurlieu
Venmo: @Legend_gary
Thank you
Join this channel to get access to perks:
/ @autopurlieu

Пікірлер: 140

@Jonny5aliv3 Жыл бұрын

If you hold your key guide at a 45° angle facing up, it will make it easier and more accurate when setting the distance of the block

@autopurlieu Жыл бұрын

Yes and I tried that. Unfortunately, the probe and cutter won’t reach the bottom part of the key. I meant to extent the key blade over the top so it will cut from top to bottom .

@Jonny5aliv3 Жыл бұрын

Lol, You scared me I watched this video as a refresher, been four or five years since I cut one. It’s the only blank I have but I just tested it. It works fine. Thanks for the refresher video. Do you have any on the programming?

@autopurlieu Жыл бұрын

@@Jonny5aliv3 yes. You can browse my playlist. Plenty of different kind of programmers video

@legacyagro-techtourtv4779 4 ай бұрын

How can I get this machine and at how much.

@phileban4314 2 жыл бұрын

very good video!

@syanoHMUF 2 жыл бұрын

Amazing and satisfying video

@autopurlieu Жыл бұрын

Thank you for your support

@surreyhub7108 4 ай бұрын

Hi the bro that’s a cavity key cutter not laser as shown on title. Great job for a budget machine 👍

@autopurlieu 4 ай бұрын

Maybe you have a different definition. You can google what “laser key” means. Thank you for your support 🙏

@ricardowhyte6100 Жыл бұрын

Nice video, remove the nuts and just use the black handles that came with the machine I had issues with that part of the sitting up until I figured that out

@autopurlieu Жыл бұрын

Thank you , yes , I’ve remove the nuts. It’s driving me nuts lol. It makes a lot easier 👍🏽

@ricardowhyte6100 Жыл бұрын

@@autopurlieui saw that lol, when I first got it I was using both nuts n handles the key kept flipping out and also damaged 😅 so I sat and think

@mosestm1099 Жыл бұрын

Which nut

@ricardowhyte6100 Жыл бұрын

@@mosestm1099 the nut thata between the black tighten knob

@mosestm1099 Жыл бұрын

@@ricardowhyte6100 thank you

@user-qj2hx4zt9g 11 ай бұрын

gracias por la ilustración😊

@autopurlieu 11 ай бұрын

Denada ! Thank you for your support 🙏

@levipankey 2 ай бұрын

Will this cut regular car keys as well?

@rocfamilyvlogs8060 2 жыл бұрын

Wow nice video

@ultimatecracksmokingwarloc184 2 жыл бұрын

Great video

@autopurlieu 2 жыл бұрын

Thank you, pls share

@bhagwaanbhagti2325 Жыл бұрын

Nice

@shoehorny6844 2 жыл бұрын

What size cutting bit did you use? You make it look so easy! Nice video.

@autopurlieu 2 жыл бұрын

Thank a lot . I used 1.5 but I think I could’ve used 2.5 with no problem and it would cut faster.

@frankmata1812 Жыл бұрын

Compared to other KZfaq videos right?

@RobertDickens2002 Жыл бұрын

I have same question do you happen to have a link to tool in each side

@autopurlieu Жыл бұрын

@@RobertDickens2002 link on what is it ?

@surreyhub7108 4 ай бұрын

That would be 2ml

@rocfamilyvlogs8060 2 жыл бұрын

Hello po watching now

@alifneiche9693 9 ай бұрын

I got a question I did duplicated a key for a crv but it won’t turn the ignition but the original it does turn it but I have the same bite

@autopurlieu 9 ай бұрын

Sometimes when the clamp is over tight it goes crooked at end tip of the blade. It goes sideways. That makes it not turn the ignition cylinder .

@alifneiche9693 9 ай бұрын

@@autopurlieu so what should I do

@istvanmeissler2238 2 жыл бұрын

What machine did you use to program the key to the car's immobilizer? Thanks.

@autopurlieu 2 жыл бұрын

For this particular one, I used Launch X431 V pro. I do use APP most of the time now

@istvanmeissler2238 2 жыл бұрын

@@autopurlieu APP ? Which is that? Thanks.

@autopurlieu 2 жыл бұрын

@@istvanmeissler2238 AutoProPad , I used in this video kzfaq.info/get/bejne/rNhhnaVput7MlnU.html

@istvanmeissler2238 2 жыл бұрын

@@autopurlieu Thank you very much for the information and for your video. Very good information. Best wishes to you.

@autopurlieu 2 жыл бұрын

@@istvanmeissler2238 thank you brother.

@ohmchatuphorn1222 Жыл бұрын

What size adapter or spacer are you using? and where to find thank

@autopurlieu Жыл бұрын

I had a home made spacer. But I believe there’s a pair selling on eBay

@RobertDickens2002 Жыл бұрын

Everytime I do this it seems like there's a 1/16 inch difference between the tracer and cutting bit

@rocfamilyvlogs8060 2 жыл бұрын

Done share en watching

@user-wf8cb2eq3f Жыл бұрын

Super!

@ymg200 Жыл бұрын

I have a similar Honda key. Where I can cut the duplicate? I stopped at HD, they said they don't do Honda keys. I just need to cut, no programming is needed.

@autopurlieu Жыл бұрын

Ace hardware do cut and program. Or find a local local most around or look on Facebook marketplace

@sboyd7551 2 жыл бұрын

nice video

@autopurlieu 2 жыл бұрын

Thank you

@O3ZN 9 ай бұрын

Physical key is fine but how is the bluetooth unlock is working? Please explain...

@autopurlieu 2 ай бұрын

What Bluetooth ?

@RPdesign71 Жыл бұрын

Great videos! Just got the same machine. Tried to cut my house key #68 and HY17 ( Hyundai key), cut 5 key total and none of it work. Just wondering what bit do you recommend using for both? Salamat po!

@autopurlieu Жыл бұрын

Maski yung house key doesn’t work? When you say doesn’t work, it won’t turn to lock or unlocked ? Make sure na align na align sya . Pati yung depth

@RPdesign71 Жыл бұрын

@@autopurlieu ayaw sya mag turn. Maybe I’m using the wrong bit and tracer. I’m new to this maybe I just need more practice. I love your videos. Salamat po. Rey form Reno Nevada

@autopurlieu Жыл бұрын

@@RPdesign71 mahirap talaga pag house key. Kc hindi sya made for that kind. “Laser high security @ type key sya. Tulad sa video ko. Yung flat parang pang honda. MAs maliit na bit and probe, MAs accurate . Kaso, dapat dahan dahan. Kc madaling maputol. Yung bit at tracer dapat match ang size

@RPdesign71 Жыл бұрын

@@autopurlieu I was able to make two house key :). Tried to make HU100 key for Chevy Cruz ( laser cut), wasn’t successful full. Felt like the bit was worn down. Cuts were not smooth. I’ve only done about 10 keys on this bit, how long do they last? Thx

@autopurlieu Жыл бұрын

@@RPdesign71 depends on how you use it. You must cut it slowly a little by little so it won’t worn out easily . And maybe replace the cutter with better quality . China made kc

@betozavala1535 Жыл бұрын

I saw that you put something under the key, what is that for?

@autopurlieu Жыл бұрын

So it won’t sit too low. If it sits too low, the top layer gets flat/flush on the holder. It will cut the holder.

@golden98_. Жыл бұрын

Where did you buy the keys that are not yet cut ?

@autopurlieu 11 ай бұрын

Local key distributors

@golden98_. 11 ай бұрын

@@autopurlieu thank you man 🙏🏿

@richardnazar1214 2 жыл бұрын

done

@Zay_.dtm1 10 ай бұрын

I just got my key made a hour ago why is this on my suggestion I didn’t even ask how they cut them

@autopurlieu 10 ай бұрын

Hahahaa I have no idea brother

@dammdaniel9953 4 ай бұрын

You know your phones is listening all time and can surprise you by such unexpected spying results . Isn't it terrifying , gov is spying on people by using their cellphone.

@GoBigAutoDetailing 4 ай бұрын

Your phone has a microphone, it listens to everything you say, ever seen adds of something you've talked about on Facebook, Instagram etc? That's why.

@DhoTjai 3 ай бұрын

You share your location with google?

@pouncerminned863 2 жыл бұрын

Wish you could have shown setting the machine up, I think you have to do a few tweaks to it before using it

@autopurlieu 2 жыл бұрын

I barely use this manual machine now but once in a while I use it . The most critical part is to set the level tip of the both cutter and the other tip level. Maybe I’ll make a quick video how I do it

@autopurlieu 2 жыл бұрын

Check my new video , I hope it helps you. 👍🏽

@pouncerminned863 2 жыл бұрын

@@autopurlieu thank you for taking the time to do the video!!!! needed this really badly

@autopurlieu 2 жыл бұрын

@@pouncerminned863 check it now. It’s already uploaded . Not sure if that’s what you need . I hope it helps. Just message me if you need more help. 👍🏽 or if anything I can help remotely

@pouncerminned863 2 жыл бұрын

@@autopurlieu i just bought this deful 389A machine and wanted to know how to set it up out of the box, as I heard you had to fix a few things on it in order to cut properly

@mrbeeman2166 Жыл бұрын

That's good

@autopurlieu Жыл бұрын

Thank you sir

@user-ju2ne6go2e 4 ай бұрын

Is it possible to cut a key without a copy on the other side? When customer has lost all keys scenario. If not how to do it?

@autopurlieu 2 ай бұрын

Not with this machine. Cut it by key code

@SaltPapiii 5 ай бұрын

Hi! I’m kind of interested learning skills such like this. Do you know a store located in the PH you can recommend for me to buy tools like yours? Thanks.

@autopurlieu 5 ай бұрын

Where in Philippines are you?

@SaltPapiii 5 ай бұрын

@@autopurlieu Thank you for the swift response. I’m from Leyte po. Ormoc city.

@autopurlieu 5 ай бұрын

@@SaltPapiii boss, Wala ba nyan sa Lazada or shoopee?

@SaltPapiii 5 ай бұрын

@@autopurlieu May nakita nman ako kaso im kinda hesitant kasi. Yung ibang stores, iilan lang sales. Concerned ako baka ma scam.

@JordanGodwin-mm9pn 10 ай бұрын

Is this a chinese machine would this work to cut keys in the uk please ?

@autopurlieu 10 ай бұрын

What kind of keys do you have in UK? This is for high security blade key, will also work on regular side key blade

@JordanGodwin-mm9pn 10 ай бұрын

@@autopurlieu transponder keys ? i just need to get a programmer and get the machine so i can learn to do it myself struggling to find a cheap programmer for the uk

@POKEMONGOEPISODESHindi Жыл бұрын

Which key is best pital or loha I means duplicate or original After we lost the key

@autopurlieu Жыл бұрын

They would be the same

@POKEMONGOEPISODESHindi Жыл бұрын

@@autopurlieu local duplicate key handle lock ko khrab kar deti hai

@autopurlieu Жыл бұрын

@@POKEMONGOEPISODESHindi I am sorry, I am not fully understanding your question

@capitalerose6410 Жыл бұрын

Hey i started following you because i found this interesting... if u dont mind... whats the name of that machine? I would like to buy one because im the guy that loses keys like crazy lol

@autopurlieu Жыл бұрын

It’s a DEFU vertical manual key curing machine

@capitalerose6410 Жыл бұрын

@@autopurlieu thank you so much brother i appreciate you and i will continue to like your videos because it is very helpful. Thank you again!!!

@autopurlieu Жыл бұрын

@@capitalerose6410 I appreciate all your support 🙏

@iankelly2110 10 ай бұрын

hi, can the DEFU 368A cut Gm key,s. thanks

@autopurlieu 10 ай бұрын

Yes

@iankelly2110 10 ай бұрын

@@autopurlieu cheers

@Chuck-tq3kq 9 ай бұрын

Where do I get one?

@autopurlieu 9 ай бұрын

eBay or alibaba

@fordfiesta07TVDriving 8 ай бұрын

Hi Guys

@josesantiago1123 2 жыл бұрын

Donde queda la parte del la programación

@autopurlieu 2 жыл бұрын

Check out my other videos. I have plenty of videos how to program. Most Honda are almost the same process of programming (Honda Pilot / Accord / Acura )

@mosestm1099 Жыл бұрын

Can this cut hard iron

@autopurlieu Жыл бұрын

No it won’t .

@mosestm1099 Жыл бұрын

@@autopurlieu thanks

@autopurlieu Жыл бұрын

@@mosestm1099 no problem . Trust me I tried it hahaaa Broke my cutter lol

@mosestm1099 Жыл бұрын

@@autopurlieu ok good information

@jamesmurphy3788 Жыл бұрын

Start a note that tall women die What's the Tory of D Wales

@danallansarthou7 Ай бұрын

Duplicate key model for honda civic? 5:04

@RaviShanker-zb3vu Ай бұрын

Iska price kya he

@reymarkmatinao7485 2 жыл бұрын

Invited by Jocelia Ugbamin

@darin7220 5 ай бұрын

why are these keys called 'laser cut'. I don't see a laser involved in this process.

@gracewahu3829 6 ай бұрын

Prce in kenya

@autopurlieu 6 ай бұрын

Sorry I’m not a seller

@JoseIsaachd 2 ай бұрын

Pero las llaves están al revés

@autopurlieu 2 ай бұрын

What backwards ? Need cut. Both sides lol

@user-su8kb9ym1g 13 күн бұрын

إسم الماكينة أخي

@mdarifhosen2845 8 ай бұрын

Price in Bangladesh

@autopurlieu 8 ай бұрын

$1000

@felipedejesusgarcia6283 8 ай бұрын

Gringo wey sustituye las tuercas por las mariposas naranjas de plastico

@aibsmusic2820 9 ай бұрын

Your soap address

@akjain773 7 ай бұрын

Contact details

@autopurlieu 7 ай бұрын

Facebook page “auto purlieu”

@angrydetapul7503 4 ай бұрын

I need a duplicate key. ... your address.

@autopurlieu 4 ай бұрын

For what car year and model?

@angrydetapul7503 4 ай бұрын

@@autopurlieu R15 V3

@autopurlieu 4 ай бұрын

@@angrydetapul7503 what is that lol. A bike ?

@angrydetapul7503 4 ай бұрын

@@autopurlieu yes

@autopurlieu 4 ай бұрын

@@angrydetapul7503 go to your local locksmith. They can do it for you. I will need your bike to program it

@TMB03 2 ай бұрын

Very bad machine not recommended

@autopurlieu 2 ай бұрын

It’s actually not bad for personal use or back up manual machine

@8290Wgu 3 ай бұрын

totally not accurate, have got day

@LockMaster4you 10 ай бұрын

Nice

@autopurlieu 10 ай бұрын

👍🏽

@richardnazar1214 2 жыл бұрын

done