How to Wire a Race Car | Relay Fuse Panels

No video

How to Wire a Race Car | Relay Fuse Panels - Part 1

Рет қаралды 15,674

2 жыл бұрын

Relay/Fuse Panels: airdout.com/co...
I walk through how to wire up your car project with one of my panels! This is part 1 and i will have part 2 out later this week showing you how it will all look once installed in the car!!

Пікірлер: 26

@MRE_Motorsports 2 жыл бұрын

Getting ready to wire one of these up in my mustang !! Good stuff

@hybridzdrift Жыл бұрын

Just bought mine, 12 way with switches panel, Hard to beat!!

@AirdoutRacing Жыл бұрын

Will have it built/sent out soon!

@weshanson7408 23 күн бұрын

Could you do a continuous solenoid instead of the 200A relay? Or why would you like pick one over the other?

@andrewoglevie5401 2 жыл бұрын

Just ordered a 6x6. Very clean set up.

@supreme2544 2 жыл бұрын

I would get my money back. Thats a horrible quality panel. Your asking for corroded wires and terminals.

@matthewfenton8775 Жыл бұрын

@@supreme2544have you used one to know? Of the panels inside it shouldn’t Corrode surely?

@khancross 5 ай бұрын

Instead of several relays which are ignitioned triggered, why not to add just one giant 200A relay and let this control an extra fuse box. This wiring will be ignition triggered and attached to this fuse box are components like power windows, headlights, turn signals, horn, radiator fan, fuel pump etc. Will this work?

@KSwapTheWorld69 3 ай бұрын

I Am Planning On Doing This To My K Swapped 69 C10. It Is Know In My "K-Swap" Album.

@mitchellplatin5580 5 ай бұрын

This is great. But I didn’t see how the fuses were wired into the circuit.

@AirdoutRacing 5 ай бұрын

Fuses are all in the middle under plastic over

@vapate84 6 ай бұрын

do you happen to have a diagram showing how the flasher relay works with the main fuse panel?

@driftykamryn 2 жыл бұрын

Hey man. Im currently in the middle of building a relay panel for my drift car. I am curious if I can wire a toggle switch in place of the "key" switch.

@AirdoutRacing 2 жыл бұрын

Yep! Can do that no problem

@octanemayhem2686 2 жыл бұрын

Bro that is clean asf. I like how the inputs and outputs are on opposite sides. So basically you're bypassing things like immobilizer and 'main' relay.? Also if I'm deleting the dash/main harness for this setup what about the cluster ?

@AirdoutRacing 2 жыл бұрын

Yeah I completely rewired the whole car, not using cluster since the Holley comes with a screen. May upgrade to their large dash in the future

@LJ-zz4so 2 жыл бұрын

Getting ready to order this panel from you. What size wire is needed to power the relay board?

@AirdoutRacing 2 жыл бұрын

@@LJ-zz4so depends on panel, but the 12 way. Suggest 2-4 gauge

@benvandeyssel4359 7 ай бұрын

Awesome work but if using a stand alone Holley system the power and ground go straight to the battery or you will have problems in the Holley instructions they will tell you many times.

@AirdoutRacing 7 ай бұрын

Yes we always do that, just talking about wires to tell the Holley to turn on