Where did you Connect the trigger cable? Pink or Brown?

@@AlbertoTV85 start watching at 2:10 in the video. It shows it.

@@AlbertoTV85 pink

Also had a golf mk6 and was in tail light and did not work at all. Had i did like this it would work. Its get power from stereo so no need tail light.

Big facts 💯

I recommend hooking up the ground, less your head unit becomes the ground in a short. Its like hooking up the 3rd green wire ground on a ceiling fan. That would be my assumption why the wire is there.

Which unit do you have?

Did you get this to work on your caravan?

It sounds like you need to change the camera settings

He probably can't say yes for sure, now that so many models are out now. You could try a test light on the plug to see what it powered when the car is shifted into reverse?

@@jonny5ive167 Okay, sounds like a plan bro. Thank you 👌🏽

Did it work after cutting wire from canbus?

No, it’s not the same. You should have a single connector dedicated to the camera. Thanks for watching.

No

If not power to the red wire (the one who connect to the Third like on the video) when reverse then take the positive from the back up light.this is that works for me

You can splice into it

It needs to be grounded to the vehicle. Find a metal spot somewhere close the camera to attach it, preferably underneath out-of-sight. You may have to drill a hole and use a screw if you can't find anywhere.

The signal is sent by can bus system.

Did you ever figure that out ?

For some models it isn’t necessary

ever get yours to work?

soldering is always better. do the pull test and you'll see . but not everyone has solder..

A mi me pasa lo mismo. No sé cómo solucionarlo.

Wifi and bluetooth antenas. 👍🏻

It's a non sense. Accessory wire send 12v constantly when ignition is on. The camera will be always powered when u drive. And the cable camera going to the head unit has only the video connector and a little red wire. This red wire should be connected to the trigger and plug the yellow connector with the yellow "camera in" connector of the head unit.

Any advice on this question I'm having the same issue in my vw cc

My guess is it's wrong power red/pink wire connection,?? Your radio might need a different color wire to source power from

All was wired correctly. Oddly enough, I got it to work by cutting/disconnecting the black wire for the camera. I’ve seen several others say the same thing worked

@@rm.builds was that black one is @7:42 or @6:44 that you had to disconnect (and reconnect or leave it disconnected permanently) Thanks

It would work without connecting the ground so your issue is probably something else

@@audiovisionusa on the back of the radio I plugged into the 3 pin (pink or brown like they say) the red cable from the main cable that connects all the way to the camera in the back also that red wire is plugged whit the red from the connector power of the camera, in an android unit whit canbus,

Then that ground cable I didn't connect to anything, losing hope on that back up cam...

@@jorgebicho2216 is your vehicle automatic? And does it switch to reverse option by itself when put in reverse?

@@audiovisionusa no, it's manual

did you ever get yours working? Cannot get video on mine either.

Your unit is probably slow or faulty. With Canbus, as soon as you go into reverse it will signal your camera, if it’s not adjusting then no wire changes will fix that. Even if you link it to your taillight I’m pretty sure it would still do that, not sure just my thought

@@raquellewis7294 I dont think my unit is slow nor faulty. The iso and all that is controlled by the cam so it probably takes a minute to start up and adjust it all. My thought was that i might be able to circumvent this by having it powered all the time.

It's basically always the third one. The one next to the red cable. It's often pink, in my case it's brown.

@@ParodieHecker-mobile Thank You

Is it right? Have u tried ?

That's the hope, at least. Seems like sometimes it works and sometimes it doesn't. Dependent on whether you have an 1. auto vs manual transmission. 2. If your canbus actually "communicates transmission gear reverse" as some canbus are designed for other features in different cars and may not be associated with transmission gear status. If this is the case then even if you have a canbus - it won't work if you splice it like in this video. To figure it out (I think) just hook up your android head to power before you do any splicing and cutting and just put your car in reverse and see if the android head screen switches to a "Reverse cam view" regardless of if the cam is actually attached. I guess the only plus to attaching the cam before you install it is to confirm that it draws enough power from the "reverse" wire.

ever get yours working? Having the same trouble with mine.

did you ever figure this out?

I managed to make the connections only that the signal seems to be disturbed and the image is visible like old TVs when the signal is poor. Can someone help me?

Some cameras can be retained

@@audiovisionusa Thank you very much for the quick reply! Any idea on how I can find out more detailed information about my particular case? It's a European 2011 Chevrolet Orlando

If you had the rear black wire connected to ground, try disconnecting it. Because ground has already been provided by the yellow coax connection.

@@zaidzaid4747 so we don't even connect black wire to rear lights ground??

@@divyanshugogna6152 I think the yellow RCA cable is the ground, so (i guess) no need for the ground (black cable)

@@ronaldd.1355 I got mine installed yesterday even though i have canbus but i had to connect it as a non canbus car for reverse camera to work with my car. The correct wiring for me was At front - connect red wire to pink trigger wire, and yellow to yellow (camera input) Pink wire wasn't open hence i had to splice it and then connect to red wire. At back - 1. connect reverse light + wire to Both red wires ( camera red power and red going to front in convince wire) 2. At reverse camera yellow to yellow and red to red. Also i have tried using t taps and crimpers they are $h!t honestly. Never trust them. Best to solder it, then solid connection.

@@divyanshugogna6152 Thanks for your info. Maybe your point #1 (reverse light) is the same as pink wire (so I guess if you leave it unplug it would be sufficient).

Hi 👋 the power comes from the canbus. If you connect it to the reverse light as well it will send a unnecessary signal when in reverse and it could damage the canbus after a while, which will then cause the radio to not function properly.

@@audiovisionusa @AudioVisionUSA okay thanks so if we so have canbus, its best to wire like in the video first, and then if still not working like this then only connect the red rear to power positive from reverse light. Got it thanks. Will avoid wiring like normal. I was just unsure because I'm buying canbus for an older car like 2005 opel corsa c, so unsure whether that canbus would be sending reverse signal or not (its mainly for steering wheel control i think). Can i just another question if we need to plug rear red to power positive, can we still do that (if wiring like in video isn't working) and then not connect the red power from yellow RCA to front of radio? Thanks again your very helpful

@@divyanshugogna6152 if it automatically switches to reverse without the camera being connected then the canbus triggers the reverse camera. If it doesn’t then you have to wire it like the other video we have. If you have manual transmission you will most likely have to wire it directly to the reverse light

@@audiovisionusa its automatic transmission, and it show what gear is vehicle in on car's dashboard, so i guess canbus should automatically switch it. I will wait for stereo to come and report back thanks again.

Then? What's your report? Regards