Hummer H3 Water Pump Replacement - How to - Water Pump Replacement Hummer H3
Рет қаралды 3,025
7 ай бұрын#mikesmancave #hummer #hummerh3 #generalmotors #howto #howtovideo #toledo #toledotools
Hummer H3 Water Pump Replacement - How to - Water Pump Replacement Hummer H3
Contact me at : mikesreviewvideos@gmail.com
Other Hummer Videos :
H3 Viscous Fan Removal : • Viscous Fan Removal - ...
Hummer H3 Fuel Economy : • Hummer H3 Fuel Economy...
Hummer H3 Battery Upgrade : • Hummer H3 Battery Upgr...
Why I Drive a H3 Hummer : • Why I Drive a H3 Hummer
Hummer H3 Service Indicator Reset : • Hummer H3 Service Indi...
Hummer H3 Stereo Panel Removal : • Hummer H3 Stereo Panel...
@joshuawiggins6637 4 ай бұрын
Helped me out a lot I know what to do now instead of going in blind
@MikesManCave 4 ай бұрын
IT's not that hard, as long as you have the correct tools I have mentioned. 👍👍
@bluesteel5841 6 ай бұрын
Very good thank you. I needed this info. Best one I seen on KZfaq..
@MikesManCave 6 ай бұрын
Thanks for the feed back, I wasn't even going to make this video till I saw how bad some of the other were. 🤣🤣
@CanadaLifeVlogs Ай бұрын
Very good video
@MikesManCave Ай бұрын
Thanks for the comment, much appreciated, I was not even going to make a video on this, but then saw how bad the others were one literally showed the old water pump in position and the flipped to the new one installed.
@hugeslacker 6 ай бұрын
Thanks for making this video! I am ordering my water pump right now and wanted to make sure I had everything I needed.
@MikesManCave 6 ай бұрын
Yeah you will need the fan spanner. The rest is pretty basic.
@hugeslacker 6 ай бұрын
@@MikesManCave I ordered a 36mm spanner. Hopefully it's long enough. Otherwise I'll have to weld something to it haha
@MikesManCave 6 ай бұрын
You will probably have to grind it down, I had a 36mm spanner, but it would not fit into the gap, and it was too expensive to grind down, but some are more slim line. See how you go. @@hugeslacker
@hugeslacker 6 ай бұрын
@@MikesManCave This one is the thickness of a bicycle pedal wrench... It was off amazon labeled as a viscous fan clutch wrench. I have a grinder though if I need it!
@MikesManCave 6 ай бұрын
@@hugeslacker That one should be fine.
@bridgetrobertson7134 4 ай бұрын
I love Aussie car repairs. Don't let them replace you.
@MikesManCave 4 ай бұрын
Ok.
@TheRopenNetwork 3 ай бұрын
Good vid, but the belt was difficult to follow. Do you remove it completely? We have a couple of H3T's in our fleet. Same process but very difficult.
@MikesManCave 3 ай бұрын
check 14:30 minute mark
@ajsalazar82 Ай бұрын
My fan moves when I try to loosen.
@MikesManCave Ай бұрын
Need the right tool and do it exactly as I show it. Make sure you are turning it the right way. There is no other way really that I can think of.
@thedealkingz2606 2 ай бұрын
32 are 36
@MikesManCave 2 ай бұрын
Sorry I have no idea what that is supposed to mean.
@thedealkingz2606 2 ай бұрын
@@MikesManCave Is was the size of wrench you used
@thedealkingz2606 2 ай бұрын
@@MikesManCave I got the 36mm on the way
@MikesManCave 2 ай бұрын
@@thedealkingz2606 Yes, you need 36mm.
@MikesManCave 2 ай бұрын
@@thedealkingz2606 That's the one you will need, it's not a hard job, and well worth doing.
@MrPhlypc 27 күн бұрын
Wrong coolant should have dexcool
@MikesManCave 10 күн бұрын
Interesting, I will look into that.
Bell Road Toyota Video Inventory
Рет қаралды 12
Jose Mechanics
Рет қаралды 4,5 М.
Bloody Knuckles Garage
Рет қаралды 4,3 М.
兔子警官
Рет қаралды 2,8 МЛН