How To Remove Can-Am 850/1000 Outlander/ Renegade Primary Clutch
Рет қаралды 64,194
2 жыл бұрынwww.hunterworks.com
This video is about how to remove and replace the primary clutch on the 850/1000 Can Am outlander, renegade, og mavericks and some commanders
@MaelLauzon 2 ай бұрын
Very helpful and clear video! I was taught to use a ratchet strap to hold the clutches, using a breaker bar. It works great.
@scotthaller7268 2 ай бұрын
Very clear and helpful instructions. I used impact wrench without any issues…made the job easy. I have a Gen 1 Outlander 800 and noticed in my owners manual the torque for the primary clutch bolt is 74lbf*ft…the video mentioned 89 which is too much for the G1.
@Hunterworks 2 ай бұрын
The 89 is for the model in the video and while i am a impact guy I never use it on a can am, you got one shot to get this right, if it turns on the shaft it will rarely hold again
@renter003 Жыл бұрын
Watch a couple of your video’s , must say some of the best I have seen great info 👍👍👍
@Hunterworks Жыл бұрын
I really appreciate that
@CYOTsNiper 5 ай бұрын
Would you suggest putting blue loctite on the primary as you did for the secondary? I would love to get a belt if you made them for the 450!
@Hunterworks 5 ай бұрын
I do not but it can't hurt but only blue
@FML.P.J Жыл бұрын
Do you know if on 2022 570 xmr if bolt is reversed threaded or normal? And the torque specs?
@Hunterworks Жыл бұрын
Unfortunately, I do not know either. I’m sorry.
@plwa1207 6 ай бұрын
Did I miss something, I don’t recall you showing how to put the 2 little spring back under the bearing assembly
@Hunterworks 6 ай бұрын
You didn't, looks like I didn't do it but we have a video about the bearing too. kzfaq.info/get/bejne/i8qYicx4ysqlpHk.htmlsi=uUaOVmP23LYiCS94
@motorsector274 5 ай бұрын
Perfect video 🙏
@CYOTsNiper 5 ай бұрын
If you have a 2022 outlander 450 the primary has left hand threads.
@TheGraneable Жыл бұрын
Hi, I have an older model, a 2006, i've taken the primary clutch bolt out, but the assembly did not spring out, how can I pull it out ?
@Hunterworks Жыл бұрын
The outside half is suppose to come off like this one
@TheGraneable Жыл бұрын
@@Hunterworks That's what I've tought, i'll just hammer it down with a rubber mallet and see what happens
@adan8890 Жыл бұрын
@@TheGraneable I have a 19 commander and had to give it a little love tap and it popped right off
@crazylifeofme6465 7 ай бұрын
I have a 2023 can-am outlander 850 max XT what size clutch tools do I need
@Hunterworks 7 ай бұрын
Size?
@crazylifeofme6465 7 ай бұрын
@@Hunterworks I was told I needed the right size for my bike or do all work this is my first time working on one I need to take them off and give my primary and one way bearing a good cleaning maybe even my secondary
@Hunterworks 7 ай бұрын
@@crazylifeofme6465 I guess a belt change tool and a torquing tool you don’t need a clutch puller unless you’re taking the back half of the primary off but if you’re gonna take it off, then all three they can be found on our outlander page on the website
@crazylifeofme6465 7 ай бұрын
@@Hunterworks what tool was it that you used to loosen the belt is it universal
@tylerhunt9676 8 ай бұрын
Where can I found that clutch puller
@Hunterworks 8 ай бұрын
On our website
@tylermcbride2807 11 ай бұрын
Is that bolt on the primary an upgrade. Mine is a 2021 1000 xtp max and has that torque to yield fastener.
@Hunterworks 11 ай бұрын
What is a 21 XP can am?
@tylermcbride2807 11 ай бұрын
@@Hunterworks outlander model
@tylermcbride2807 11 ай бұрын
@@Hunterworks whenever you take the primary off you are supposed to change the bolt with the 703500842 kit from can am.
@Hunterworks 11 ай бұрын
@@tylermcbride2807 it’s the original bolt.
@tylermcbride2807 11 ай бұрын
@@Hunterworks what machine was it on this video again?
@jesusayala5355 8 ай бұрын
I got a 2011 renegade 800r is it the same process?
@Hunterworks 8 ай бұрын
Pretty sure I’ll have to look at parts diagram to be sure
@jesusayala5355 8 ай бұрын
Ok thanks 👍
@chiloquinvectorcontroldistrict 11 ай бұрын
Hey, might be nice to mention that the bolt os removed turning clockwise, not counter-clockwise
@Hunterworks 11 ай бұрын
What bolt? Both primary and secondary bolts on this one are right hand
@edwardhorvath5731 10 ай бұрын
The primary (front one) is reverse thread on the 2005 Can Am Outlander. I found that out the hard way, by having it cranked on till it broke. It then came out with my finger, when turning reverse.@@Hunterworks
@Hunterworks 10 ай бұрын
@@edwardhorvath5731 Oldest outlander we have worked on is a 22, sorry this was not accurate
@CYOTsNiper 5 ай бұрын
@@Hunterworks I have say with my 22 outlander 450 I to thought it was right hand thread on the primary and snapped it! After picking up the head of the bolt off the floor I saw the LH stamped in the head of the bolt! 🤦♂️ lesson learned the hard way! When I get the replacement bolt and torque it to specs, I’m still going to be nervous even knowing the correct thread direction now!!! lol
@budgetendurogroup9635 Жыл бұрын
This video just cost me a days work 😂 the bolt on mine was threaded the opposite way so snapped it with impact gun 😂 are the bolts expensive
@Hunterworks Жыл бұрын
Sorry to hear that. What was you working on?
@budgetendurogroup9635 Жыл бұрын
@@Hunterworks outlander 450 2016 it’s turned out ok in the end I got the snapped threads out and a new bolt for £15 and a valuable lesson learned, I was trying to change bendex
@Hunterworks Жыл бұрын
@@budgetendurogroup9635 This video is about a 850/1000 so I would not know what a 450 has unfortunately, glad you are able to easily fix it
@wallyyuriy8912 27 күн бұрын
@@budgetendurogroup9635how did u get the snapped threads out. I just did the same thing on my 2016
@budgetendurogroup9635 26 күн бұрын
@@wallyyuriy8912stud removal tool cheep of eBay
@wallyyuriy8912 27 күн бұрын
I busted the main bolt on mine. I think it might be left hand thread
@Hunterworks 27 күн бұрын
I don't know of any that are
@wallyyuriy8912 27 күн бұрын
@@Hunterworks just found out that lots are left hand thread just on the primary. Secondary are all normal right hand thread
@Hunterworks 26 күн бұрын
@@wallyyuriy8912 Very odd. But depends on way the engine tures or on what side of the engine.
@wallyyuriy8912 26 күн бұрын
@@Hunterworks pretty common now that I know. Same side as your video. This is a 2016 can am 450. Though. But wish I knew before. Going to be fun getting the broken threads out of the crankshaft hole
@Hunterworks 26 күн бұрын
@@wallyyuriy8912 Sorry, never had a 450 clutch apart.
Aspen Offroad
Рет қаралды 22 М.
EPIperformance
Рет қаралды 2,3 М.
ADVENTURES This Way
Рет қаралды 6 М.