HurryUpPinball - How to install a Flipper Coil Sleeve and Coil Stop Bracket

Рет қаралды 7,645

4 жыл бұрын

Welcome to HurryUpPinball - a show where I teach you how to work on your pinball machine. This tutorial will show you how to install a flipper coil sleeve and coil stop bracket. This installation with take about 15 minutes and require minimal tools.
If you are looking for information regarding the Pinball Life coil stop brackets, they can be found at the following link:
www.pinballlife.com/coil-stop...
Be sure to follow HurryUpPinball for news about upcoming tutorials.
Facebook & Twitter: @hurryuppinball
Instagram: hurryuppinball
Twitch Streaming: HurryUpPinball

Пікірлер: 32

@ashmath82 Ай бұрын

I am newer to pinball and your videos have been life savers. Thanks for doing these!

@HurryUpPinball Ай бұрын

Thanks for the feedback. I had a hard time figuring some things out so I thought I would do my best to help others with common problems. Pins aren’t that scary once you get used to certain things. Glad to see the hobby continue to grow and hope to help that any way I can.

@scottoneal2744 Жыл бұрын

Clear, concise instructions for us newbs. Thanks for the great content

@dennisd4027 Жыл бұрын

Subscribed...this is how pinball tutorials should be done! Thank you!

@HurryUpPinball Жыл бұрын

Thanks for the sub! I really appreciate it.

@OldManMickeltons 5 ай бұрын

Thank you so very much for this tutorial! Much much appreciated

@txag007 8 ай бұрын

Great video! Thank you for the detailed information.

@mphenriksen 11 ай бұрын

New to hobby. Great stuff thank you for making this easy to follow along with. I appreciate it!

@codykirkland9002 2 жыл бұрын

Thanks for the slow tutorial! About to do some touch ups on my Operation Thunder.

@user-ow2dh5rw5z 3 ай бұрын

Will do swapping the stops/sleeves on my DP Pro later this PM. Machine has about 800 plays and I could pan for gold in the bottom of the cabinet. Ha. Should have swapped them earlier as I did when I had my EHOH. Great video/tutorial!

@HurryUpPinball 3 ай бұрын

They seem to have gotten better over the past year but the pinball life ones work great and last a long time if you are looking to switch them. Thanks for the feedback and the support!

@user82938 Жыл бұрын

Thanks

@greaseman6387 3 жыл бұрын

What a great video - really well done.

@HurryUpPinball 3 жыл бұрын

Thanks Dirk. I really appreciate the feedback!

@rcfreeman 2 жыл бұрын

your video made a subscriber out of me. Nice job.

@HurryUpPinball 2 жыл бұрын

Thanks for the support. I really appreciate it.

@bobbyzilliox5294 3 жыл бұрын

Well done.

@fatguyinatesla5780 3 жыл бұрын

Subscribed and thanks for this video

@HurryUpPinball 3 жыл бұрын

Thanks for subscribing and for the the support. I really appreciate it!

@SteveJones172pilot Жыл бұрын

I assume it would have been a good idea to clean the plunger that gets pulled into the coil as well, since the old sleeve was so dirty. Anything to recommend to use or not to use when cleaning that? I assume even just a damp cloth may be enough..

@HurryUpPinball Жыл бұрын

I typically use a paper towel and a citrus degreaser spray (typically buy ZEP). Spray it on the paper towel then wipe down the metal part of the shooter rod. I works really well to clean the metal.

@TheGameRange 2 жыл бұрын

Great instructional video! Should you use Loctite when installing the new coil stop bracket?

@HurryUpPinball 2 жыл бұрын

You can if you like but I traditionally don’t. I see that more frequently on the bally / Williams games. I have stripped a few screws before so I usually don’t but I check things frequently to make sure they aren’t coming loose.

@BruketFans 2 жыл бұрын

Great instruction/video :-) Regarding the Pinball Life link and the coil stop brackets, which part number is it on the bracket you used? Thank you in advance...

@HurryUpPinball 2 жыл бұрын

Here is a link to the stern coil stops I use. Sorry for the delay in responding. www.pinballlife.com/flipper-coil-stop-for-sternsega.html

@AvalancheDan186 3 жыл бұрын

Great video! Do you have any videos on how to do a full stern flipper rebuild? I need to do on my TWD premium, thanks!

@HurryUpPinball 3 жыл бұрын

I have not needed to do one yet but as soon as I do, I’ll be sure to make a video on it. May have a chance to do one on a Williams game soon. Picking one up very soon.

@AvalancheDan186 3 жыл бұрын

@@HurryUpPinball that would be awesome! Love the content you have put out so far. Your videos are always straight to the point and clear, but m a subscriber!

@lanceanderson3150 5 күн бұрын

i heard you do house calls for about $3.50

@stephenhardie3658 2 жыл бұрын

I have to replace a coil sleeve for the scoop for a Monster Bash remake pinball machine. Is changing the coil sleeve for the scoop pretty much the same as replacing a coil sleeve for a flipper? Thanks!

@HurryUpPinball 2 жыл бұрын

Sorry for the delayed response. It is a very similar process to changing the flipper coils. Just take a picture with your cell phone of the mechanism before you remove it to change the coil stops. You just want to make sure you reinstall it the same way that you removed it.