Husqvarna Chain Oiler repair and Easy Clutch Removal Hack

No video

Husqvarna Chain Oiler repair and Easy Clutch Removal Hack

Рет қаралды 93,529

Coconut Productions

Күн бұрын

Husqvarna Chainsaw Oiler not working. Easily removing the clutch and assembly to access and change the chain oiler.

Пікірлер: 37

@mikegrant5435 6 ай бұрын

Excellent. Wish you could teach other tubers to make concise, informative, no nonsense videos.

@noelpeterson5591 Жыл бұрын

I have the same saw it's over 20 years old & has been sitting for about 15 years wrapped up in an old shirt, got it going in 5 minutes, runs great again.

@tubefishing6969 Жыл бұрын

Great news!!! That's what it's all about!

@jefffrayer8238 Жыл бұрын

I just worked on my 345 which is exactly the same except the chain adjuster is different. Big warning here : Use a small flashlight to look down in cylinder. Rotate the clutch in the direction to remove it and make sure piston rises above exhaust port before shoving rope in. If you fail to do this you can push rope out exhaust port so piston will try to shear rope off. Simple, easy check to avoid problems. To tighten you reverse the process but you should remove rope starter assy. so you are not pulling against dogs, pulley and handle instead of rope in cylinder. Good video.

@calisdad3 4 жыл бұрын

Clear, concise, no music- thanks.

@TheOlsonOutfit 4 жыл бұрын

I used your rope trick a couple days ago, worked like a charm!

@coconutproductions6550 3 жыл бұрын

Perfect

@gordonbournival152 Жыл бұрын

Thanks for that video, short and very useful !

@mtaviator 4 жыл бұрын

Quick, concise, effective. Thanks!

@coconutproductions6550 3 жыл бұрын

Glad it helped!

@keithwade7881 2 жыл бұрын

I used your method with the rope. It worked fine for removing the clutch. Only problem is removing the rope once clutch reinstalled. Any hints would be appreciated.

@mikekotarba5828 Жыл бұрын

Thank you for making the video

@Dan-zi4 4 жыл бұрын

Is it ok to not insert rope like you show when removing the clutch or does this damage the saw in some way? I've never used rope. I just give the clutch a light hit with a hammer then turn until I feel the most resistance then hit again. Takes 5 or 6 times of doing that and usually it's loosened enough to unscrew by hand. Is the rope simply to make it faster but not necessary? Thanks.

@coconutproductions6550 3 жыл бұрын

Some may not release that easily Daniel, but if you have a system that works, thats great too! Thanks for sharing.

@allenr265 5 жыл бұрын

I have a Husqvarna 345 which leaks chain oil excessively is this normal or can I do something about it. It leaks until it's empty, and do you have a video out showing this fix? Thanks mate.

@tubefishing6969 5 жыл бұрын

I would take it apart and take a look at the oiler mechanism. It's a five minute job

@allenr265 5 жыл бұрын

Thanks Mate

@sambonelife7485 5 жыл бұрын

I have a husky 455 Rancher that had the same problem I set it on the Shelf came out the next morning and there's a puddle of oil underneath the saw. I took it apart the side cover that is and pressure washed it all and took apart all of the oiling system that little 10 plate that's behind the body of the saw and your bar and cleaned all that out and put it back together and it fixed the problem I must have had a piece of debris holding it open and allowing it to leak out the reservoir tank.

@MrAtaripitbull 4 жыл бұрын

Just used your video to replace the house, the oiler cog looked good. Put my Husqvarna 440e X torque together and gonna give it a couple of hours to see if that's the cause of my bar chain lube leak ?

@MrAtaripitbull 4 жыл бұрын

Well after replacing the bar chain oil tube, pump and even the metal plate, my husqvarna still leaks like a pig. I will never buy another Husqvarna again..

@coconutproductions6550 3 жыл бұрын

Great to hear!