Excellent. Wish you could teach other tubers to make concise, informative, no nonsense videos.

Great work! This is what it usually comes down to. We have to get creative and make something perfect ourselves.

Do you sell these?

Yep, got a 09 Mazda 5 that spit one out just like this. Bout to order the bushings and do both sides. I like these videos like this so I can glance through them and see what kinda job it's going to be. Other than having to get dirty and hardest part of getting up n down in the ground ( bad foot / ankle ) just getting up the mood to actually do it will be my hardest part.

Is this the same process with the cx9?

I just worked on my 345 which is exactly the same except the chain adjuster is different. Big warning here : Use a small flashlight to look down in cylinder. Rotate the clutch in the direction to remove it and make sure piston rises above exhaust port before shoving rope in. If you fail to do this you can push rope out exhaust port so piston will try to shear rope off. Simple, easy check to avoid problems. To tighten you reverse the process but you should remove rope starter assy. so you are not pulling against dogs, pulley and handle instead of rope in cylinder. Good video.

Dumbass. You’re suppose to have a continuous flame 🔥

Thanks a lot, it's very helpful.

'preciate it. very informative.

You better turn that star adjuster in a lot.....otherwise you're gonna break your brake cylinder by forcing them off this way.......Cause the shoes will hold in the drum if you don't UN adjust them first........There's a little access port on the back of the brake to use 2 screwdrivers to do that...one holds back the adjuster spring....the other one turns the star wheel....... .. Z

Thank you for making the video

Thanks for that video, short and very useful !

I have the same saw it's over 20 years old & has been sitting for about 15 years wrapped up in an old shirt, got it going in 5 minutes, runs great again.

what is an 8 L bolt?

Flamethrower next please.

Love this guy....absolute legend

B U T T E R

0:40 OH LAWD THEY COMIN

Thanks for posting!

I Sawed The Demons.

Well done mate 👌

I used your method with the rope. It worked fine for removing the clutch. Only problem is removing the rope once clutch reinstalled. Any hints would be appreciated.

$700 Labor for 6.5 hours DFW.

they sell these super handy little metal things you can actually thread into the oil filter when you take it off and there is a little handle on it when you screw it on so you can pull out the oil filter and not spill any oil when doing so!, i use them at work all the time and it’s awesome. good video btw i just wanted to watch to see if you any tips of taking those fucking things off because they’re a pain for sure haha

They called doom guy

Quick question. How many trailing arm bushing are in a 2006 Mazdaspeed Axela ?

Know if you need an alignment after this? Took it to a shop said they didn't find anything wrong but i do have the rattling noise which makes me believe its the bushings. But this shop does keep saying im going to need an alignment after the job.

This man woke up and chose violence

Doom guy when he sees a gore nest

Yes Ma'am this is wasp removing experts how can we help you Lady: I need a small nest removed The guy with a mini flame thrower and chainsaw: *IM ON THE WAY*

should’ve burnt the inside

Good for a step by step but if you only want to do this once and make the install easier replace these with the powerflex bushings. See my review on them. Otherwise you will have to do this again in the future.

Finally recommended

Cheers man!

what causes it to wear out like that?

I personally after all of that wor bought the powerflex version and since it is a bit more expensive it will last twice as long as the OEM part and comes with an incredible warranty but if the our ring was in descent shape SuperPro make another nice one that slides right in the ring and also has a better warranty than the OEM part

Same on Volvo C30 , s40, and others!😉

Have you tried placing the bushing in the freezer and the arm in anoven or heat theend with a torch? we used to do this to put bearings in place in quick change rear ends using this approach, bearings inthe freezer and rear end center section in an oven.

Asmr

kzfaq.info/get/bejne/kLuIaK6btpmceGg.html

I hate wasps and love this 😍

thank you

Is it ok to not insert rope like you show when removing the clutch or does this damage the saw in some way? I've never used rope. I just give the clutch a light hit with a hammer then turn until I feel the most resistance then hit again. Takes 5 or 6 times of doing that and usually it's loosened enough to unscrew by hand. Is the rope simply to make it faster but not necessary? Thanks.

Yo that’s sick

Just used your video to replace the house, the oiler cog looked good. Put my Husqvarna 440e X torque together and gonna give it a couple of hours to see if that's the cause of my bar chain lube leak ?

Great Video! Made in USA

Thanks A+

oh, ok i forgot the queens dead

seriously!!! theyre just gonna make another one!!!

Quick, concise, effective. Thanks!