Hustler Raptor Deck Issue Fix | How to fix bent idler pulley! (Old Video)
Рет қаралды 11,821
3 жыл бұрын#Hustler Raptor deck issues fixed. I noticed the belt kept coming off of my deck, even a new belt. Started inspecting and noticed the idler pulley leaning bad. Came up with a simple, easy and cheap solution to #diy and fix the issue. This is a simple video on #howto fix it yourself as I've done here. Hope this helps
@Retired683 Жыл бұрын
I watched your video but i do not have a welder. I straighten the deck with a small mall. I then used an old blade and put the carriage bolt through and tighten it up with my impact . works great. It was your video that had me looking for a way to support it. Thanks
@BackFortyTV Жыл бұрын
Yessir! Glad I could help!
@alloutofdonuts3998 2 жыл бұрын
I was laughing so hard when you went to drive back into position to mount the deck. I had just done the same yesterday but at first I couldn’t figure out wtf you doin lol. Glad i Found this vid cuz my pulley was angled too. Also glad I didn’t just pound it back flat. Gonna weld up some angle, good thinkin! Also saw in comments & curious how you like the BadBoy? Might get one next mower. Lots of good reviews.
@BackFortyTV 2 жыл бұрын
Lol I’ve found that was the best way for me! Haha and the maverick is an awesome machine. I went with bad boy this time because my best friend has had one for 9 years and has changed nothing but the fluids and a battery.
@keithduboseoutdoors6872 3 жыл бұрын
Thanks for the video. I also have the same problem. I just replaced that stupid belt last month and now the deck is warped causing the pulley to bend up. At least I know what the problem is now I have to get some help to get it reinforced.
@BackFortyTV 3 жыл бұрын
Glad it helped, bro! I was stumped until I started really looking. Then noticed that weak spot. I love my raptor, but it’s been beat on the past 5-6 years and this was the only real issue I’ve had. That Kohler is tough too.
@BackFortyTV 3 жыл бұрын
I could’ve done a much better job fixing it, but I’m a cheap diy guy with most stuff as long as it’s nothing major LOL.
@keithduboseoutdoors6872 3 жыл бұрын
Hey if it works it works. It doesn't have to be sexy
@BackFortyTV 3 жыл бұрын
@@keithduboseoutdoors6872 that’s right!
@keithduboseoutdoors6872 3 жыл бұрын
I didn't realize your channel was about hunting etc.. I just subscribed. I am into the Outdoors video stuff too
@daniellucker 2 жыл бұрын
Check your pto clutch bolt mine just snapped off same exact mower that may be causing vibrations as well
@adb6777 3 ай бұрын
Good video. Question...Do you know what the metal pan insert which is welded to the deck that the spindle is screwed into. The welds failed on my hustler and I can't find a replacement. Thanks
@BackFortyTV 3 ай бұрын
I’m not sure I understand.
@adb6777 3 ай бұрын
kzfaq.infoemO8zlJWVGQ?si=6bLrNf6CsAA3OE4o
@adb6777 3 ай бұрын
That is the part in question. I tried to weld it back on but it failed. Thanks
@adb6777 3 ай бұрын
@BackFortyTV It's the metal pan that the spindle screws into on the deck. The welds on mine failed and the whole thing fell out of the deck...leaving a empty hole where it was . Thanks
@andrewsmith941 3 жыл бұрын
I have the same mower and noticed mine was bent the other day. I ordered a new belt but will not install it now until I get it straightened out.
@BackFortyTV 3 жыл бұрын
Hope it helps out.
@45DerekS 3 жыл бұрын
Having the exact same issue. Did this fix the problem long term? If not I am repairing and selling the darn thing.
@BackFortyTV 3 жыл бұрын
It sure did. Been using the fire out of it since. Haven’t had belt issues since the fix. Only issues I’ve had is I busted the fuel tank, but that was all me.
@ILOVEYESHUA1ST 2 жыл бұрын
Hey did this fix your issue. I’ve got a similar issue I believe (2 belts) later.
@BackFortyTV 2 жыл бұрын
It sure did.
@daniellucker 2 жыл бұрын
How did you straighten that pulley out???
@BackFortyTV 2 жыл бұрын
I just took it off and knocked the deck where that pulley mounts straight. Just banged it with a hammer until the deck was straight. Then re mounted the pulley and put the braces in.
@577buttfan Жыл бұрын
My harbor freight welder saves my ass so many times .
@BackFortyTV Жыл бұрын
Yessir!
@geraldgrandfield2031 3 жыл бұрын
Having the same problem on Rapter 36.
@BackFortyTV 3 жыл бұрын
It’s a pain. I sure hope the video helps.
@chrissteininger6097 2 жыл бұрын
Just wondering if this is still working for you? It just happened to me and I'm wanting to know if it's a long-term fix. I noticed that I was still working ten months ago from a comment. So is she still going?
@BackFortyTV 2 жыл бұрын
Still kicking strong!
@BackFortyTV 2 жыл бұрын
I have a bad boy maverick now, but gave this one to my mom. Still cuts good.
@ColeParkerrr 2 жыл бұрын
I thought mine was supposed to be bent. Okay what we’re the symptoms of the bent pulley? Just a terrible intermittent vibration?
@BackFortyTV 2 жыл бұрын
Yes bad vibration and it eats belts.
@BackFortyTV 2 жыл бұрын
The vibrating also causes other bearings to go out faster.
@ColeParkerrr 2 жыл бұрын
@@BackFortyTV sick. Thanks for the quick reply. I’ve changed 3 spindles. Must be the reason. Fixed everything still vibrating. I thought it was supposed to be angled lol
@BackFortyTV 2 жыл бұрын
@@ColeParkerrr lol I understand. Also check blade balance for vibrations. If they’re beat up and out of balance it’ll cause issues also.
@ILOVEYESHUA1ST 2 жыл бұрын
34$ on line
ohboyoutdoors1
Рет қаралды 143 М.
DIY JIM
Рет қаралды 336 М.
Raley's Small Engines
Рет қаралды 10 М.