Hydro gear ZT 3100 transaxle problem identification and repair

Рет қаралды 29,996

Жыл бұрын

I'll show Ya'll how I diagnosed the problem with the Hydo gear transaxle. Also, I'll show how I replaced the necessary parts.
This one is out of an TORO / Exmark stand on 30" aerator, but these same transmissions are used on many mowers too.
Hydrogear transaxles zt series 2800, 3100, 3200 are all nearly identical design so this can be helpful in regard to any of those models.
* Disclaimer: This video is for entertainment purposes only. KZfaq, NotoriousJPG , the video creator and/or affiliates are not responsible for any damage, injury, or loss of any kind that may result from following instructions, statements or actions in this video. We assume no liability or guarantee of any kind. If you utilize any portion of this information, it is at your own liable risk including that of safety or property. We suggest hiring a pro or consultant to complete the items shown.

Пікірлер: 20

@gtinteractivedesign 8 ай бұрын

Update: there are over 200 hrs on the rebuild now. No Issues so far. Btw all the internal parts are available. Hydro-gear tech support is very good. On their website you can download the service manual. Also, if you call their tech support number they can provide you exact part numbers for anything that you might need based on your exact model number.

@Scoot7827 5 ай бұрын

Thank you for sharing! Great demo of your work on the pump. We have the 3100 as well. New at 50hrs I drained the oil, repl the filter. About every 100hrs I service it again. Blow off grass/debris after every mowing. After 330 hrs or so the left charge pump o ring developed a leak. Picked up a HG oem o ring. Didn't observe any scoring on the pump parts. Torqued the 12mm bolts 60in lbs then 110lbs. refilled w/ oil and will complete the purge process later today. Cheers!

@JM-yx1lm 8 ай бұрын

All you have to do to check the cylinder block pistons is push one down all the way, plug the hole with thumb on other side and let go of rod, if it holds vaccume then its good. Also when you take the pistons out , there are little spacer things inside that can fall out so dont lose them.

@zorantamamovic7296 Жыл бұрын

Hvala puno na korisnim savjetima.

@charleskutrufis9612 Ай бұрын

Hi, Thank You for the video, very informative. Please say where you got the parts. If you did ,I missed it.

@turdsandwicher Жыл бұрын

Did it work out for you when it went back on the aerator? I'm working on a "Hydro gear" transmission from a Honda Snowblower. There was a decent amount of metal shavings on the magnet but I am stumped as to where it all came from. The faces on the pump and motor look pretty good. All the gears look perfect. I'm going to look closer at those pistons maybe there is play in them thanks for the tip. Apparently no internal parts are available to purchase only a basic seal kit is sold by the company.

@notoriousJPG Жыл бұрын

Yes everything worked like brand new once on the machine.

@kr5289 9 ай бұрын

I'm in the process of taking apart the pump on my gravely mower when I took the charge pump cover off there is quite of bit of scaring around it on the case side what do you think could have caused it? the pump actually locked up while I was mowing. thanks

@notoriousJPG 9 ай бұрын

There were probably some metal shavings floating around in the fluid. Also check the bearing and bushings for any play. There shouldn't be any movement in them.

@kr5289 9 ай бұрын

@@notoriousJPG thanks

@michaelcongilio7484 21 күн бұрын

You could've gave a better instruction on the bypass rod and plate underneath that. An intricate detail. No mention.

@jremeee1599 2 ай бұрын

I just picked up a mower with hydro gears 3400. 420 hours. They are noisy. At idle they wine real loud. Not sure if the oil has ever been changed in them.

@notoriousJPG Ай бұрын

Check oil level, then replace filters and fresh oil... Could be oil issue or air in the system.

@jremeee1599 Ай бұрын

I dropped it off at the Husqvarna dealer last week. I praying they are not toast. The fluid is full but dirty. It runs fine just really, really loud.

@jremeee1599 Ай бұрын

The noise sounds like it’s coming from up near the fans.

@swink49 2 күн бұрын

Ya well I did exactly what you did except it wasent 100 mph I couldn’t get that damn center peace out beat the hell out of it for an hr! So through the dam thing through my fucking window

@peanutman6593 4 ай бұрын

Hydro gear transaxles need repair a lot because they’re junk. I will never buy another mower that features a Hydro gear time bomb transmission

@rickcoleman8903 3 ай бұрын

90 percent or more mowers use these hydro gear units.

@user-io1ki3rn9j 2 ай бұрын

I agree the hydro gear transaxles are garbage. I’ve owned 2 exmarks with this set up and have had nothing but problems. Things leak like crazy. I’ve had to get units rebuilt and have had to replace a unit because of it. Had one hydro gear that started leaking before warranty was up and exmark replaced it. I have that same mower in the shop now getting a seal kit installed due to leaks. I had an older exmark lazer z I ran for years that had a split pump system with wheel motors. Never had a bit of a problem with that system. There are still zero turns made that use the spilt system. I just bought a scag tiger cat 2 with a similar setup to the old lazer z. I am done with the transaxle.

@notoriousJPG Ай бұрын

Personally, I like the older style setup with separate wheel motors and pumps.