Hyundai Tucson wheel bearing replacement (pressed in)

Рет қаралды 38,746

2 жыл бұрын

Disclaimer: This youtube channel is intended for informational purposes only. The jobs that you see on these videos are based on my knowledge and experience as a technician. Information provided through this youtube channel is not intended to serve as a substitute for your professional technician/manufacturer.

Пікірлер: 30

@Dee12327 2 жыл бұрын

I kept the rie rod, and strut attached and used a manual press, and a slide hammer.. worked pretty good, its that stupid snap ring!! I got it out fairly ez, i just mangled it out, but putting the new one in.. OMG broke 4 pairs of snap ring pliers.. wow

@hyundaitech 2 жыл бұрын

Nice, i never tried that one.

@Dee12327 2 жыл бұрын

@@hyundaitech i didn’t want to pay for an alignment lol I’m cheap. So i just dropped the ball joint and left the strut and tie rod connected

@hyundaitech 2 жыл бұрын

@@Dee12327 hahah nice you need whats best for you

@dmytrolototskyi Жыл бұрын

Hello, I like your video. Is it necessary to make wheel alignment after replacing rear bearing? Thanks.

@hyundaitech Жыл бұрын

Technically everytime you move something from suspension and steering you need to do alignment, but if alignment not accessible its not end of the world in my opinion, everything should be fine.

@Jbs116 2 ай бұрын

Need to replace the stud bolt on my tucson. Is there an easier way than removing the spindle, replacing the bearing and using a press?

@hyundaitech 2 ай бұрын

Is it on the front or rear? Front maybe theres a room that you can just hammer it out depends on the room. And usually theres a slight room to just hammer out the affected stud. But if you are replacing the whole spindle i think thats different situation.

@Jbs116 2 ай бұрын

@@hyundaitech front. I got the old one out by using an angle grinder. But having difficulty putting in the new bolt.

@hyundaitech 2 ай бұрын

@@Jbs116 so when installing you need a spacer before you install the nut then you can tightened the nut and the stud will just go in. Check online search wheel stud installer.

@Jbs116 2 ай бұрын

Thank you

@maynardacenas4150 2 ай бұрын

Sir is hyundai tucson 2009 model a press in hub bearing?

@hyundaitech 2 ай бұрын

Yes

@Bob-zd4od 2 жыл бұрын

Is it recommended to replace the knuckle

@hyundaitech 2 жыл бұрын

Not really, the knuckle is for life, unless the bearing is stucked for good and then yeah no choice but to have a new knuckle. So far in my experienced never happened yet. Hahha.

@Bob-zd4od 2 жыл бұрын

@@hyundaitech thanks so much.

@zachross6832 Жыл бұрын

Did u use the same spindle

@hyundaitech Жыл бұрын

Yes i use the same, the only new is the bearing and snap ring

@Marloni.Royalty 2 жыл бұрын

What model and year is that Tucson?

@hyundaitech 2 жыл бұрын

Its 2011-2016 tucson

@daniloazuelo3046 Жыл бұрын

Kabayan ,i have hyundai tucson 2015 gls 2.4. Looking part # of wheel hub bearing left rear

@hyundaitech Жыл бұрын

All wheel drive?

@daniloazuelo3046 Жыл бұрын

@@hyundaitech its 2wd

@hyundaitech Жыл бұрын

@@daniloazuelo3046 52730-3S200 but double check with your vin number if that matches. Hope that helps

@daniloazuelo3046 Жыл бұрын

@@hyundaitech thanks bro

@joesrustshop4509 2 жыл бұрын

Did this to my girlfriend's car. I looked into it, and found they have loaded knuckles. For some cars,.......unfortunately not this one. Those would make real quick work out of this.