Part 2 kzfaq.info/get/bejne/rKmJm899ybGahGQ.htmlsi=XRQ6JNXrV_0N7Ese

Just discovered this channel and couldn't get over how amazing the $600 boat turned out so I started watching what else there was. I'm going to say that was about 3 hours ago but I'm not mad about it.......... I only wish I had this guys talent. Great videos brother thanks for sharing

Nice video, Looking forward to seeing this channel grow!

You been very lucky so far on the deals your getting! A+

👍👍👍👍👍🤜🤛 I used to use diesel oil in my car, even though it wasn’t a diesel engine. I ran it only in the summertime and in the fall I used to change it back to regular oil because the diesel oil would protect the engine better.

Thank you, Sir! I enjoyed your video, and especially liked what you said about diesel oil in air cooled engines. I didn't feel good putting 5W30 or 10W 30 in my push mower. It looks like you were blessed with a great opportunity in the Hustler, and are doing a great job bringing it up to speed.

use a wrench called a Crows foot that should work to tighten that hose

I would take the plastic off the engine and make sure the fins are clean and clear. As nasty as that was its got to be dirty there too.

What did you find with the Scag Wildcat bad smoking problem? Great find and fix.

I came across your videos very randomly via the KZfaq algorithm, I’m assuming. I love watching anything that gets fixed or put back together. Just a BIT of constructive criticism, I too wanted to know what happened with the Scag on the previous video. If you are going to post another project, just let your viewers know you’re still planning on continuing the previous build at the beginning of the next project. That way we know. Other than that, you have yourself a new subscriber. Looking forward to more videos.

Great video … thanks for the diesel oil tip… also would love to know what you paid for the mechanics special mower ?

Imagine selling a nice lawn mower over a starter and plug gasket.. that's crazy to me.

Wow! That seller sure has a lot of money to be able to afford to sell that one cheap and just replace it! How much did you pay? Such obvious and easy fixes! You must lead a charmed life! 🔧😉👍

Great success!

Tank's

You gained a new subscriber

Brand new mower you git a steal on a great mower.

Gas filter change out. Good you are going to get the hydro fluid changed.

How much did you pay for

14:35 I don't know how a person could do that. Short of the washer falling off and getting folded over the last time the plug was removed. At that point I'd toss the washer and run it if I had to. 16:09 That is an NPT fitting. Kohler does not use NTP drain plugs. I don't think anybody does anymore. You want an o-ring boss/flange face fitting. You are flirting with danger running NTP on a parallel thread. NTP seals by thread deformation. To get the deformation requires a lot of torque. If the fittings are not designed for it... something cracks... or something vibrates loose... and you are deforming threads that should be left alone. 19:14 I've run diesel oil in all engines my entire life. I only stock 5w-40. I'd run it in that hydraulic system without a concern.

I doubt it ??!!

I’m thinking he never serviced it period, hope the compression is good 👍. But it was a good deal and you can fix it up

What you should do where you put that drain hose just get a piece of old garden hose and wrap up great where it hits the metal then zip tie it on protection

I did the same with my raptor

Too hard putting it in ??

What’s up with the scag ace?

Date and hours on filter

Good find I had same start problem on donated mower starter cable read good voltage and Olms but had a break that someone had taped over would not even click solenoid replaced cable good to go.

Hey Guys, How are your nerves after watching this?

I worked for Hustler for 45 years. Get that side discharge chute back on!!

First

Hi there! We'd like to invite you to work with us on some boat products. Are you interested in working together? Please let us know how we can contact you. Thank you!