I DIDN'T KNOW HOW TO INSTALL TEE IN SMALL SPACE BEFORE THIS SECRET TRICK.
Пікірлер: 125
@letsbereal-hd8qt3 ай бұрын
repair coupling is the right way. but I am impressed with these tradesmen who do so much with so little.
@sleektoneofficial4 ай бұрын
Shouldnt heat it you should use a slip coupling or use a flat rasp to file down the stop inside a regular coupling.
@sstjacques3 ай бұрын
I like this, heated to reshape before cement instead of buying coupling adapters. A small space to work, and other pipes already in place.
@orraman54273 ай бұрын
Imagine how much simpler it would have been if the Tee had fitted before someone put a handful of mortar around the pipes.
@jwmax12343 ай бұрын
Maybe when putting the pipes in before you set them in concrete you put the tee in and there is no problem?
@jimdodge57664 ай бұрын
2 unions and 1 coupling will fix it correctly
@Repo89713 ай бұрын
That’s what I was thinking the entire video. Doesn’t heat reduce its integrity?
@victorbastidas65933 ай бұрын
The easiest thing I would’ve done is to cut pipe at the end where there was a 90 degree elbow where the pipe goes into the ground it would have eliminated all that work
@user-xv5uo1po9t3 ай бұрын
I don’t like the heating. There is a better way.
@danielcarter3052 ай бұрын
I was literally coming here to say the same thing. Bet this guy spent a couple hours fixing this simple plumbing problem if he would have done it the correct way it would take 10 minutes at the most.
@petermapp59882 ай бұрын
I agree with your comment....but...if in the bush....no stores around that are open...this....will....work.Btw......this is a nice exam question
@123ykraps4 ай бұрын
Super heating to bend the pipe and then reheating will result in a shorter life span of the connections
@olliechristopher4673 ай бұрын
No it won't. I have done this trick dozens of times. Last time was in the 80's and water pipe is still holding strong after almost 40 years.
@DB-dm2xmАй бұрын
@@olliechristopher467 good for you its still a hack job
@exceleratorjoshua4 ай бұрын
Repair coupling ended up being used since you see near the end of the video cement was removed to finish the repair on one of the lines.
@UKSA1232 ай бұрын
Okay so what's the lesson in this? Well just for starters...if you leave just one of the pipes mobile this goes together easy. Second, if pipes are not mobile at all, you can use a PVC compression coupling or dig up one side left or right to bend that joint together. From a former irrigation installer.
@kimantoine134 ай бұрын
Great work.... Like the way you straighten The pipe back
@asgplumbing7813 ай бұрын
Whenever you add heat to something you alter its structure molecularly so therefore it's probable that is fittings were not properly installed in a leak may result
@Peter-fo4ec2 ай бұрын
Agree
@timo40402 ай бұрын
That was the best method to repair a horrible situation. Good job. Hope it’ll help me in the future
@dominicbianchi72984 ай бұрын
Looks good but won’t last under pressure. Proper repair would be to use 3 threaded unions. The integrity of the pipe was ruined with the heat gun & bending of the pipe
@Ruinsthename2 ай бұрын
If I fixed stuff like this I would be without a job. This is criminal...
@stevecaudell86094 ай бұрын
Easy, get 3 slip joints
@MollyMacPack3 ай бұрын
Try doing that with Schedule 40 pipe.. works well with drains, though! I like!
@garlandmoney93104 ай бұрын
Why not bust open the tops of the other two pipes, so you could get repair couplings down in there? Actually you would only need to open the top of one more pipe. The first pipe would have plenty of room for a coupling if the others were moved out of the way.
@erikbrantner42953 ай бұрын
Because they were too lazy to do it! Lol
@jimw16152 ай бұрын
It's nice to know he is using a BLACK+DECKER Heat Gun, Corded, Dual Heat Settings up to 1000 Degrees, 1350 Watt (HG1300).
@alinnewjeresy4 ай бұрын
Schedule 40 pipe in the USA is too thick for this trick
@petermapp59882 ай бұрын
I was just thinking the same thing....schedule 40 and schedule 80.....I as in ME....have encountered difficulty in trying to manipulate pvc with heat
@marh7624 ай бұрын
Tane ajo filozofi per ta riparu.Matje shmatje tundje gisht.Qesharake!
@BearMountainBigfootRescue2 ай бұрын
The fly was trying to tell you, "Dont do it this way," but flies are hard to comprehend.
@dr.emilschaffhausen46832 ай бұрын
Be sure to check back on the follow up video: Repairing Leaks You Caused Yourself
@martintheron13864 ай бұрын
Just fittings that fit inside pvc pipes
@mikelastname2 ай бұрын
In a pinch I have done something like this to make a M-F pipe into a F-F, but do yourself a favour and use a tenon saw for cutting the PVC - it is much faster than a hacksaw and you get a straighter cut.
@bogbean37743 ай бұрын
Should have cut the pipes to the correct length and fitted the tee piece before burying the pipe work, it would have been a lot quicker.
@brainards114 ай бұрын
Good work...but probably took 12 hours to complete!
@davidgentz17313 ай бұрын
Like to see him do that was scheduled 40pipe
@chrisviolette89914 ай бұрын
That's why no hub is so awesome plus it's quiet when some one flushed. No hub can be installed pulled apart and reinstalled no problem.
@georgetsetsakos60882 ай бұрын
patel! that's some dope pvc cement right there
@vijayxyz12 ай бұрын
Sure is!
@williamkechkaylo79153 ай бұрын
we NEVER use thin wall under ground!
@victorbastidas65933 ай бұрын
That’s why they manufacture compression Ts
@isaganimendoza95564 ай бұрын
🎉must be one side extension in straight line is longer to be an ajuster,
@chrisjames99424 ай бұрын
Rubber fernco couplings will fix it. Not affro engineering.
@steveshaw31453 ай бұрын
I guess if you don't have access to the right parts this would be ok, but not the correct choice. I am guessing India where all our safety training videos come from😆
@Peter-fo4ec2 ай бұрын
Where's the purple stuff..... Amateurs
@-LeAnDrO-sAnToS-7-L.s.7-4 ай бұрын
Seria mais prático ter usado quatro curvas de 45 graus e colocado o t no cano do centro não iria precisar fazer embolso com fogo o barato sai mais caro mais pra frente precisar refazer o serviço novamente
@jimdodge57664 ай бұрын
He doesn't have a clue. It won't work for long if it works at all
@andrewpowers70342 ай бұрын
As soon as I saw this guy cutting pvc with a wobbling hacksaw instead of proper cutters I knew he didn’t know wtf he was doing.
@wlh2272 ай бұрын
Won't meet code where I live and can be done very easily with slip connectors which are made for situations like this. I feel like you should include a warning that the way this was done will not meet code in some locations.
@miltonturner29773 ай бұрын
You forgot the cleaner/primer (the purple stuff). It makes sure the glue adheres to the plastic. Without it you could easily get leaks.
@krishnareddy28032 ай бұрын
Lovely
@shawnfinlay49524 ай бұрын
What a complete cluster. I'm sure most of you know what I mean by 'cluster'!
@krishnareddy28032 ай бұрын
Very nice
@user-qo4mk6oz4o2 ай бұрын
You should not glue inside a joint will cause blockages
@Peter-fo4ec2 ай бұрын
Not the correct way to do this you're changing the molecular structure of the PVC pipe and in New England with the seasons the temperature variations due to weather
@sandsleeper31243 ай бұрын
I'm not a plumber but this doesn't look like it is up to code in the U.S. If this is a supply it may not hold up to the pressure. If it's a drain then drain fittings should be used.
@Guitarplayer7243 ай бұрын
I’m pretty sure this wasn’t the US.
@barrys75152 ай бұрын
Ingenius!!!
@osu8953 ай бұрын
Not the recommended way. This would never pass code.
@darrinzenger38234 ай бұрын
How did that pipe stay fixable that long ?
@bdobson16164 ай бұрын
Sch 200
@theguy455Ай бұрын
But will this work with thicker schd 40 3/4" PVC piping?
@LindaBarron29Ай бұрын
Irrigation Engineer here... nope, that looks like drainage pipe and for drainage I try to never use T's but Y's... for SCH 40, is better to use threaded unions or slip couplings... good video for an emergency, but I would not recommend. And if you need to build a block/concrete box, leave room for future repairs (I always leave the fitting on one side of the box, that gives me space if I need to use couplings).
@alanwilkening56322 ай бұрын
Is this why plumbers get paid by the hour?
@user-pk3dj2gc6v3 ай бұрын
I can’t believe I just watched that.
@user-uk1uu9vt8zАй бұрын
Maybe you could have made a slip socket also …?
@MyRadDesign3 ай бұрын
Works great as clickbait, as plumbing, not so much.
@mobilephil2442 ай бұрын
Brilliant. Thanks for sharing.
@ProVest972 ай бұрын
1 union was all that was needed.
@gmwrenos72222 ай бұрын
Started the video with 3 sides cemented in. Until he had a problem with the final tie in, then the pipe was exposed on top. Kinda makes the video redundant.
@karickm12 күн бұрын
Absolutely do not use this method unless you want the pipe to fail.
@krishnaswamykrs82763 күн бұрын
நன்றி
@InHisImage11613 ай бұрын
Ferncos are my friends
@stymied35063 ай бұрын
So heating the pipe makes it weaker no cleaner and well just buy 3 couplings and be done with it ppl damn!! Probably leaking before he posted this video
@vivekanandams93954 ай бұрын
It seems it is a chamber arrangement with two inputs and one output.The output pipe should have been lower than the input level. 2)if it is one input and two output, the two output pipe s should be lower level than the one input pipe.
@albertwashingtonjr20892 ай бұрын
Install it correctly in the first place......
@ramonctorres97334 ай бұрын
Great job
@thomasporti77443 ай бұрын
Why they just won't use rubber no hubs
@lustylusty12382 ай бұрын
Chuck in 2x mac unions and youll be sweet as.
@iann55492 ай бұрын
What a bodge !!!
@kangaroogod3 ай бұрын
Or use 2 slip couplings
@ItsVideos3 ай бұрын
You massively screwed up at 6:35, and then redid it off-camera! 🤣🤣🤣
@-LeAnDrO-sAnToS-7-L.s.7-4 ай бұрын
E seu embolso ficou ao contrário.
@lectrician73 ай бұрын
Oooooooooorrrrrrrrr you could just it the correct way with repair coupling and avoid a TON of extra work and hack job!!!
@delwynpada34633 ай бұрын
😮😮😮😮
@Ty-ls5xg3 ай бұрын
Pretty impressive
@timmwhite92183 ай бұрын
Install 3 socket end unions @ ends of the tee and each pipe, tighten them, and done in half the time spent doing everything you just showed 🤔
@prakashkale97314 ай бұрын
Very nice idia
@igorbarahonaurbina13292 ай бұрын
Excelente trabajo mi amigo
@garlandmoney93104 ай бұрын
Making up 3 connections at one time? There ain't enough time, can't twist pipes into place as recommended. Bet there were dry joints, especially after heating up the glued joints to pretty up all those twists added to do this THE HARDEST WAY POSSIBLE. See, here in America, where PVC originated, we established what is called a set of BUILDING CODES AND Best Practices Standards. We created ASME and ANSI Standards, along with some pretty good testing procedures to control how those were created. But hey, the rest of the world just needs a hair dryer and some clear glue. You do you, dude. I'm guessing this is a water supply system, since the tee didn't have a sweep. And even though the pipe is grey, it for SURE isn't electrical conduit without a sweep on the tee.
@OneGrainYT Жыл бұрын
Brilliant
@erikbrantner42953 ай бұрын
Not exactly the best efficient way to get a Tee between there... That's why they invented the "telescope coupling"!
@jamespolucha87903 ай бұрын
Fantastic
@vijayxyz13 ай бұрын
Thanks
@that1guythomas4 ай бұрын
All you need is a combi
@Peter-fo4ec2 ай бұрын
Also not a good repair heating PVC changes the molecular structure here in New England with the seasons it doesn't hold up when the extremities of weather prevail shortening lifespan changing molecular structure don't know what else to tell you but you're doing it wrong do it right or don't do it at all or hire someone but I certainly wouldn't hire you
@eddiereyna115519 күн бұрын
Don’t be jealous
@rogerkilby43034 ай бұрын
Very well done !!! 👏
@randy63344 ай бұрын
Meh. I don't think so.
@suriyayadow3 ай бұрын
👍👍👍👍👍👍
@endziel90654 ай бұрын
Good grief! 🙄
@troyjackson31644 ай бұрын
this is third world plumbing a total disaster
@gopalannp18814 ай бұрын
There is a very simple method to do this, but this fellow has no ingenuity or the skill.Waste of our time
@stanleytownsend18863 ай бұрын
nah
@bobwalker22934 ай бұрын
Ever hear of a union?
@patrickhein94703 ай бұрын
How not to do it. They have slip couplings for this. 10x faster
@josephm.androne72844 ай бұрын
Pitiful…..u need a plumber
@hudsonhollow3 ай бұрын
No!!!!!
@timmytee53354 ай бұрын
This is the typical non-union lack of knowledge way to do things.
@zanegrey81962 ай бұрын
freaking hack...
@jasonjohnson87272 ай бұрын
Dude took all day to fix a 10 minute job and destroyed the integrity of that crap class pipe. Unions suck! Use a damn slip fix!