I generate electricity by walking - How to Generate free energy with smart shoes

  Рет қаралды 197,722

Skill Make

Skill Make

Күн бұрын

In this video, I show you how to turn your ordinary shoes into pleasant shoes and generate electricity using this smart shoe.To generate electricity in these shoes(footstep power generation), I have used 6 piezoelectric devices that convert kinetic energy into electrical energy.
To charge the phone using these shoes, I have used a 3.7 volt battery that charges itself using the electrical energy of the piezoelectric plates, and I give this energy to the power bank module that you can use to charge your phone.
------------------------------
for more 👇
kzfaq.info?s...
------------------------------
The insole generator peaks a voltage of 15 volts, the current may be small but the voltage is enough to damage the powebank's 5v charger (circuitry). I won't be using the 7805 since it's quite old and inefficient. Right now, my insole generator is soldered directly to my powerbank's lithium battery. It works but it's not completely not safe.
Another explanation I would like to add is that this method was only for testing to know that you can generate energy by walking. But this method is not very efficient because very little current is generated. And to generate a little energy you have to walk a lot.
00:00 generate electricity by walking
00:09 How to make wmart shose generate smart shoes
08:36 test smart shoes
#piezoelectric #freeenergy #skillmake #homemade #Electricity #Generating

Пікірлер: 246
@skillmake
@skillmake Жыл бұрын
------------------------------ for more 👇 kzfaq.info ------------------------------
@turtle2pond
@turtle2pond Жыл бұрын
You should sell it on Etsy.
@vimalpatel1227
@vimalpatel1227 Жыл бұрын
please list the components
@juancervantes8211
@juancervantes8211 Жыл бұрын
You got a good idea all you got to do is figure a way to make it water proof and fit it inside the shoe to make it look better
@chrisimandl
@chrisimandl 5 ай бұрын
Imagine going through airport security with this shoes😂😂
@anthony-leesanchez6219
@anthony-leesanchez6219 Жыл бұрын
Amazing video… why did you put the solder on the piezoelectric first and then solder them together?
@mangeshkale5402
@mangeshkale5402 2 жыл бұрын
Mind blowing idea
@owenwood6172
@owenwood6172 6 ай бұрын
I really like the idea the only flaw I see that would make this less usable is maybe the longevity of the piezoelectric pads? I’m unsure of how long they’d run for. Also waterproof but that’s not a hard fix. Great!!!
@satyambhattacharya6199
@satyambhattacharya6199 6 ай бұрын
You are negative
@siov4279
@siov4279 5 ай бұрын
thats what I was sayijng. that design would only work for so many miles.
@siov4279
@siov4279 5 ай бұрын
Then fall apart
@Hema-tj8cs
@Hema-tj8cs 3 ай бұрын
To work so long what should be corrected here?
@amn7319
@amn7319 4 ай бұрын
The more piezoelectric material, as well as a sufficient brace or chassis running from the toes and sole to the shins, thighs and waist would generate a lot more electricity, especially if running.
@periclesngon6854
@periclesngon6854 Жыл бұрын
Hello i really love your video and your way of thinking i will really like to work with u in such a project
@SatireEnjoyer
@SatireEnjoyer Жыл бұрын
Thanks a lot! I will be making this for my school project.
@SalmaHosny-sf8vy
@SalmaHosny-sf8vy 2 ай бұрын
Do you succeed in building your prototype 😢????
@jyothi3260
@jyothi3260 Жыл бұрын
Why you are using separate diodes for connecting 3 pizoelectric can we aonnect it all.
@vxxcxxy
@vxxcxxy Жыл бұрын
Bro, may I ask, is it fine if I add 47microFarad 16V capacitor?
@rajatsoni1192
@rajatsoni1192 Жыл бұрын
Thanks
@user-id4er1co3q
@user-id4er1co3q 7 ай бұрын
What is installed under the insole? Is it foam?
@essouaiedameur7642
@essouaiedameur7642 Жыл бұрын
Is it safe to cut piezo element to thinner pieces 🤔
@jaxashah5251
@jaxashah5251 Жыл бұрын
Amazing video we are making this project but can you please tell use which material you used for base board?
@namanpradhan7436
@namanpradhan7436 4 ай бұрын
I used cardboard.
@rednashherrera7564
@rednashherrera7564 4 ай бұрын
good day sir, can i ask if it's possible to make it water proof, because in our country, anticipated thunderstorms occurs😊
@paulosergio-gw1sm
@paulosergio-gw1sm 2 жыл бұрын
Amazing projects , my friend .
@skillmake
@skillmake 2 жыл бұрын
Many thanks
@cessboy8587
@cessboy8587 2 жыл бұрын
Please give Specifications of each component
@eddyyu7091
@eddyyu7091 2 жыл бұрын
A very funny and useful approach !
@skillmake
@skillmake 2 жыл бұрын
Thanks! 😃
@beebo5828
@beebo5828 Жыл бұрын
Wow that's awesome, so great. This is inspiring, we are inspired to remake your creation for educational/research purposes. ❤ Can you give us the list of all the materials that you use? Please, thank you. We are looking forward for your response, we will credit you in the appendix section of our paper. 😊
@loj4you
@loj4you 10 ай бұрын
i likded you bcause you did not have any likes you can like you self
@_tarsa_9233
@_tarsa_9233 4 ай бұрын
Very usefull
@influential7693
@influential7693 8 ай бұрын
is rectifier really necassary for this project ?
@Naufal-iu6hx
@Naufal-iu6hx 23 күн бұрын
Can i use diode 12 volt sir? Please answer 🙏🙏
@rakim126
@rakim126 4 ай бұрын
Love it
@galaxydm7900
@galaxydm7900 Жыл бұрын
what is the grey thing in between de discs and de glass?
@josefinandersson7646
@josefinandersson7646 11 ай бұрын
how long would it take to whare a normal phone? Like an iphone 6
@robertbodi2518
@robertbodi2518 Жыл бұрын
Hello guys! Why does he connect the (left) top and the bottom piezo together ? (With the red and black wires)
@dishsoap5554
@dishsoap5554 Жыл бұрын
Great video! you should link some of the components used.
@enesserim9829
@enesserim9829 Жыл бұрын
Hello my friend. The faster you reply, the better it will be for me. What is the name of that spongy material in minutes 6 seconds 3?
@rathidevirajagopal4510
@rathidevirajagopal4510 Жыл бұрын
Friend how do we connect a diode to each piezo plate I need more power pls reply fast
@Gaming_Arnav87555
@Gaming_Arnav87555 Жыл бұрын
what is the item used as base for cutting the sole shape please reply as soon as possible and it will be helpful for my science project.....🥰🥰😇😇
@narjes1996
@narjes1996 2 ай бұрын
If you knew tell me please
@thomasheisler
@thomasheisler 6 ай бұрын
That's awesome
@thierrymaggiorino3664
@thierrymaggiorino3664 Жыл бұрын
GREAT !!... Très ingénieux 🧠 💡 👌🏼👍🏼👍🏼👍🏼... BRAVO !!! 🛠️👏🏼👏🏼👏🏼...
@skillmake
@skillmake Жыл бұрын
🙏
@thierrymaggiorino3664
@thierrymaggiorino3664 Жыл бұрын
@@skillmake 😀👍🏼
@piyushlingayat6957
@piyushlingayat6957 2 жыл бұрын
Sir,which material you use to locate the pizeoelectric disk
@akashdeeplakra3583
@akashdeeplakra3583 Жыл бұрын
PVC pipe cut n heated into sheets
@user-lu5xh2ms4x
@user-lu5xh2ms4x 7 ай бұрын
Might change shoes before going on a plane.
@zafaralimengal2609
@zafaralimengal2609 Жыл бұрын
Can you help meh to answer my questions 1. How to make it fast to charge power bank in least steps (it can be done by increasing number of disks from 6 -> 12 ) or improveing bridge rectifier/ or both?????? It is actually a part of my FYP. I need to charge that shoes in least steps as possible Also suggest Me micro components if you can for Disks/rectifier/charger Please sir,
@nainikakathir795
@nainikakathir795 3 ай бұрын
can we use 3600mAh battery instead of 2400mAh battery???
@prathameshmalgunde6308
@prathameshmalgunde6308 Жыл бұрын
what is the specification of battery? i mean is it 3.7 volts 2500mAh battery?
@quinzonjohnfrancis6877
@quinzonjohnfrancis6877 2 ай бұрын
the connection of piezo is in parallel right?
@IRFANDIANWARTUTORIAL
@IRFANDIANWARTUTORIAL 2 жыл бұрын
Assalamualaikum, good job bro 😂
@skillmake
@skillmake 2 жыл бұрын
Thanks 😅
@INDIA_that_isBharat
@INDIA_that_isBharat Жыл бұрын
Can u please provide a circuit diagram
@georgechallita2526
@georgechallita2526 10 ай бұрын
what is the time estimated to charge the battery based on different weights
@ayshaalahmed6660
@ayshaalahmed6660 Жыл бұрын
what type of board did you use for the base?
@vaishnavirane7099
@vaishnavirane7099 8 ай бұрын
Same query
@LUCKY20.
@LUCKY20. 7 ай бұрын
How u got answer of this
@C-.Robotics_Engineering._.
@C-.Robotics_Engineering._. 3 ай бұрын
Sole board
@GoalPolice2024
@GoalPolice2024 11 ай бұрын
can u make same wireless charger one?
@pavanra7453
@pavanra7453 7 ай бұрын
How much current does it produce?
@krishanchand7972
@krishanchand7972 Жыл бұрын
sir i have a question that which paste you use to paste the electric generator with sole
@maranindhira6803
@maranindhira6803 3 ай бұрын
Silicon adhesive
@tallman786
@tallman786 Жыл бұрын
Please make the same video with voice explaining the materials used.
@omkarsangar3673
@omkarsangar3673 6 ай бұрын
Bro tell me one thing piezoelectric device can generate AC current then how mob get changed
@birgaripmemur9160
@birgaripmemur9160 2 жыл бұрын
Ahh piesos evrivere nice idea
@abcdgamingandcreations2104
@abcdgamingandcreations2104 Жыл бұрын
Bro circuit diagram pls
@Tejaswinis2005
@Tejaswinis2005 Жыл бұрын
Sir used one sheet no what is that name sir starting is that foam sheet or some other thing
@yohanesk.rajageru1077
@yohanesk.rajageru1077 3 ай бұрын
how many amperes is the diode?
@sugaslostteeth
@sugaslostteeth Жыл бұрын
Can someone plz tell me the list of the components used in this i am doing project on this please help me..
@mdi-vo7oc
@mdi-vo7oc 2 жыл бұрын
god of idea Thumbnail harder than video😂 If everyone had a friend like you.They were advancing in all directions. My best friend
@skillmake
@skillmake 2 жыл бұрын
Subin chgy adamy .....
@babulpegu4270
@babulpegu4270 Жыл бұрын
thanks sir
@skillmake
@skillmake Жыл бұрын
Most welcome
@AbhishekSalunkhe-fg2sy
@AbhishekSalunkhe-fg2sy 2 жыл бұрын
How much time/steps/distance will it take to charge a 5000mah battery. Or how much mah/volt energy is produced after 100 steps for both legs. Please answer ASAP, its serious.
@skillmake
@skillmake 2 жыл бұрын
in the video i walk 2 hours for this energy
@vaibhavvajpai1481
@vaibhavvajpai1481 Жыл бұрын
@@skillmake how much did the mobile get charged from walking for 2 hours
@Rocksidion
@Rocksidion Жыл бұрын
@@vaibhavvajpai1481 ~3.9V - 3.5V = 0.4V would be my guess.
@zafaralimengal2609
@zafaralimengal2609 Жыл бұрын
@@Rocksidioncan I ask how did you calculate that , explain??
@Rocksidion
@Rocksidion Жыл бұрын
@@zafaralimengal2609 At 8:50 he shows that he starts with 3.51V. At 9:29 (which the creator claims he walked for two hours), the Voltage increased to 3.90V. Just calculate difference and you get the total. Simple.
@SC.243k
@SC.243k 2 жыл бұрын
Very good 👍
@hasantey
@hasantey 2 жыл бұрын
ویدیو ندیده میگن خوبه
@skillmake
@skillmake 2 жыл бұрын
اره والا 😂😂
@skillmake
@skillmake 2 жыл бұрын
Thank you 👍🙏
@ozgur5555973364
@ozgur5555973364 Жыл бұрын
Süper ❤😊
@tigri-cr4oy
@tigri-cr4oy Жыл бұрын
what if you get wet, WITH WATER... what are you going to do?
@mohanponnada982
@mohanponnada982 Жыл бұрын
Sir by using each bridge rectifier diode ckt to each piezo plate,the size and the wires used might become more complex know sir??
@skillmake
@skillmake Жыл бұрын
Yes, you are right .But you can use chip bridge diodes
@prathameshmalgunde6308
@prathameshmalgunde6308 Жыл бұрын
What is the cost of one piezoelectric disk, which is used in the above project?
@psbmusicfactory
@psbmusicfactory Жыл бұрын
I have just Buy the piezoelectric it cost 25rs.
@RAKESH-ly3qj
@RAKESH-ly3qj Жыл бұрын
Please Can you make video about how to increase current intensity by the separate bridge diode for each piezo as soon as possible this week
@freestylechristelle1274
@freestylechristelle1274 Жыл бұрын
Use op-amp ( amplifier) to increase the current
@derky1108
@derky1108 Жыл бұрын
Do you need to charge the shoes at all or do they operate without charge? Like, after your done using them do you need them to charge or do the springs always work when and wherever?
@skillmake
@skillmake Жыл бұрын
In fact, the battery is charged using piezo plates and then the energy stored in the battery is used
@user-pt9oo4sn6m
@user-pt9oo4sn6m Жыл бұрын
@@skillmake Can you tell me how much energy you can get from steps like 10min?
@bossgaming9116
@bossgaming9116 Жыл бұрын
Can I use cardboard for the base
@ayshaalahmed6660
@ayshaalahmed6660 Жыл бұрын
why did you connect it to a battery before connecting it to the power bank charging module? can we just connect it to the power bank or would that make it less efficient?
@skillmake
@skillmake Жыл бұрын
The output current is low, so we have to charge the battery first and then use it
@air.cactus
@air.cactus 7 ай бұрын
Fun fact : I just got same idea a few days ago
@nanasu3113
@nanasu3113 Жыл бұрын
Dude i feel some like a smoke ..😁😁😁
@notesbymoni4107
@notesbymoni4107 Жыл бұрын
Could you maybe link the battery that is used?
@bharatsharma8713
@bharatsharma8713 6 ай бұрын
no battery used there
@go4himz
@go4himz 11 ай бұрын
What is the first item used?
@user-cb3un6ty5t
@user-cb3un6ty5t 5 ай бұрын
Gich 🔥🔥🔥
@rupalihingankar4092
@rupalihingankar4092 Жыл бұрын
How much energy generate in one day?
@TheFriendlyEyes
@TheFriendlyEyes Жыл бұрын
So is that a rechargeable battery?
@harnoorsingh67
@harnoorsingh67 2 жыл бұрын
Any wire works? Or what type of wire do I buy. (I am beginner)
@skillmake
@skillmake 2 жыл бұрын
you can use any type
@anuphirekoppa
@anuphirekoppa 10 ай бұрын
How much money 💲 total its got to do this
@amudhapriyane4534
@amudhapriyane4534 Жыл бұрын
You connected the piezo in series. The piezo produces Ac right, how would they sum up if they connected in series.
@skillmake
@skillmake Жыл бұрын
also you can use diode bridge for each piezo
@amudhapriyane4534
@amudhapriyane4534 Жыл бұрын
@@skillmake But that would increase the overall voltage drop. We may get very less O/P voltage
@saaddar6182
@saaddar6182 2 жыл бұрын
WoW Nice
@skillmake
@skillmake 2 жыл бұрын
Thanks 😉🙏
@daftar.wow_
@daftar.wow_ Жыл бұрын
Is it waterproof?
@mzp1965
@mzp1965 Жыл бұрын
How many power of bettery
@lakshsuman4161
@lakshsuman4161 11 ай бұрын
Do we have to take 3.7 rechargeable battery or simple one.
@bharatsharma8713
@bharatsharma8713 6 ай бұрын
you can take any battery there is no matter of battery
@todgames2180
@todgames2180 Жыл бұрын
I’m making the same porject but my piezzos doesn’t produce more than 0.1 volt, I don’t know why, I should produce 30v
@andreicabuquin710
@andreicabuquin710 Ай бұрын
hey man, just wanted to know what happened to your project?
@Dtexfact
@Dtexfact 2 жыл бұрын
wow good
@skillmake
@skillmake 2 жыл бұрын
thanks
@zaahirmohamedinshaf6234
@zaahirmohamedinshaf6234 Жыл бұрын
How many amps does this produce i know it is weak but I'm doing a project where it would need to power a 2V 5 mA light?
@zaahirmohamedinshaf6234
@zaahirmohamedinshaf6234 Жыл бұрын
I need this info as soon as possible please!
@skillmake
@skillmake Жыл бұрын
The output current is low, but if you want to increase it, it is better to connect a diode bridge for each piezo. Enough energy is produced to turn on the light
@mohanponnada982
@mohanponnada982 Жыл бұрын
Sir,can we step up the voltage which we obtain from the battery??
@skillmake
@skillmake Жыл бұрын
Yes, you can use the voltage booster module
@mohanponnada982
@mohanponnada982 Жыл бұрын
Thank you Sir
@amudhapriyane4534
@amudhapriyane4534 Жыл бұрын
How much current you are getting as output? Because to charge this much size battery, current should be more. We used the exact same configuration you used, but the amount of current is not sufficient. Is there any specific issue you resolved to get this much charging power? Kindly reply soon ya, this is for our project
@skillmake
@skillmake Жыл бұрын
Yes, the output current is low, I have mentioned it in the video description. But if you want to increase the output, use a separate diode bridge for each piezo.
@TheSimoc
@TheSimoc Жыл бұрын
@@skillmake The individual diode bridges would prevent the losses from pietzos shunting each other, but even then the current will be way too miniscule to be any way practical. Some kind of spring loaded magnet and coil assembly, or a hydraulic system making fluid being pumped between two chambers while walking, to run a small generator, would be better in providing useful current.
@sarkaprochazkova2621
@sarkaprochazkova2621 Жыл бұрын
​@@skillmake what happens if i walk to much? Can the battery overcharge and explode?
@Life-mt8zl
@Life-mt8zl Жыл бұрын
​@@sarkaprochazkova2621 Nah bro it will not😂.
@voltsonnemobilesolaranlage2479
@voltsonnemobilesolaranlage2479 Жыл бұрын
Very cool setup, why don't you build the system in a tire?
@skillmake
@skillmake Жыл бұрын
Yes, very good idea. Stay tuned for new videos on the same topic
@voltsonnemobilesolaranlage2479
@voltsonnemobilesolaranlage2479 Жыл бұрын
@@skillmake best , build it into two bicycle tyres to drive an electric motor ;-)
@vishalghadge8145
@vishalghadge8145 4 ай бұрын
Sir please guide
@kushlovetripathi
@kushlovetripathi Жыл бұрын
Bhai kitna paisa laga aapka
@darothydeka9982
@darothydeka9982 Жыл бұрын
Sir can you please explain the whole process....I'm actually a student and I'm making a science project based on electricity generation and I loved your idea but I'm unable to understand
@andyjk5974
@andyjk5974 Жыл бұрын
by just reading and making sense of it. i can help you on that. you just use the piezoelectric modules. that will give power to a power bank. that already has a charging system on it. its actually easy
@Drak_Thedp
@Drak_Thedp Жыл бұрын
Basically, those piezoelectric discs can generate vibrations when activated by electricity, and vice-versa, they generate electricity wfom bending. Like you can use them to create a simple buzzer (generating vibrations), or use it as an accoustic guitar pickup(it converts vibrations into electric charges). After these piezoelectric discs the diode bridges are located. They are there to direct the flow of energy, for the discs not to start using the battery instead.
@learningphysicswithkirrr1547
@learningphysicswithkirrr1547 Жыл бұрын
excuse me Sie, could i ask what is name of the charging modul? like a type of that modul, the code number etc? please Sir
@skillmake
@skillmake Жыл бұрын
5 volt power bank module
@learningphysicswithkirrr1547
@learningphysicswithkirrr1547 Жыл бұрын
@@skillmake yeah thanks a lot🙏🏽
@LAYATORS
@LAYATORS Жыл бұрын
Where is the bms? Also I dont think that 3.9 volts are good for the battery.
@mayur-_-maind_2864
@mayur-_-maind_2864 2 жыл бұрын
Thank you sir
@skillmake
@skillmake 2 жыл бұрын
thanks for watching mr mayur
@nihaldelicay3293
@nihaldelicay3293 2 жыл бұрын
Elektronik Malzeme listesini yazabilir misiniz proje odevimiz için lazim
@skillmake
@skillmake 2 жыл бұрын
I write in video
@hasantey
@hasantey 2 жыл бұрын
عالی بود اما بهترین
@skillmake
@skillmake 2 жыл бұрын
eshgy
@RAKESH-ly3qj
@RAKESH-ly3qj Жыл бұрын
How much voltage is generated by walking 1 meter or say that how much voltage is generated by walking how many meters
@RAKESH-ly3qj
@RAKESH-ly3qj Жыл бұрын
Please reply
@skillmake
@skillmake Жыл бұрын
Each step produces 25-35 volts, but the current intensity is low
@RAKESH-ly3qj
@RAKESH-ly3qj Жыл бұрын
@@skillmake current intensity is how much??
@kennethjohnganancial8489
@kennethjohnganancial8489 2 жыл бұрын
can it charge a 12 volts battery?
@animesavedmylife3648
@animesavedmylife3648 2 ай бұрын
Make more I series.
@beastlydowns
@beastlydowns Жыл бұрын
Could someone who has successfully made them, be convinced to make one custom for a price obviously?
@danielebcas2341
@danielebcas2341 Жыл бұрын
Pilipino does this bro. A student pilipino
@HashirEasa
@HashirEasa Жыл бұрын
@@danielebcas2341 what 💀
@atharvamore342
@atharvamore342 Жыл бұрын
Could you tell me.. How many volts does one piezoelectric sensor generates?
@skillmake
@skillmake Жыл бұрын
around 25-35 volt
@atharvamore342
@atharvamore342 Жыл бұрын
@@skillmake some says it's 5-6 volts.. What's the correct one?
@TECK2024
@TECK2024 2 жыл бұрын
your Brazil permission to publish your videos here
@032g.saiteja6
@032g.saiteja6 Жыл бұрын
Bro circuit diagram ?
@SariellaE
@SariellaE Жыл бұрын
Can I use 20mm plates?
@skillmake
@skillmake Жыл бұрын
yes you can
@032g.saiteja6
@032g.saiteja6 Жыл бұрын
Hlo Where you have got the circuit diagram.
@akvloggingchanel3641
@akvloggingchanel3641 Жыл бұрын
Bhai isme kya kya use hua h
@tarr7784
@tarr7784 5 ай бұрын
is real?
MEU IRMÃO FICOU FAMOSO
00:52
Matheus Kriwat
Рет қаралды 13 МЛН
A pack of chips with a surprise 🤣😍❤️ #demariki
00:14
Demariki
Рет қаралды 41 МЛН
Make it for Defense
10:25
DIY Crossbow
Рет қаралды 7 МЛН
Piezoelectric Coilgun
4:31
Iuri's Workshop
Рет қаралды 4,3 МЛН
Perpetual Motion Generator: HOW DOES IT WORK?
8:35
EL ANGELITO
Рет қаралды 11 МЛН
How to Make a Powerful Mini Freezer - Portable Mini Air Conditioner up to -10ºC
10:07
The Liberty Engine Project
Рет қаралды 1,8 МЛН
I Built a Transparent Katana
22:02
Mike Shake
Рет қаралды 12 МЛН
How to make  220v 6000w  Free Electricity Energy
14:26
CT Tech
Рет қаралды 5 МЛН
I turn CD/DVD into solar panel
11:26
Creators 904
Рет қаралды 1,7 МЛН
How to Make Sugar Rocket  - turning sugar into rocket (easy)
5:35
Skill Make
Рет қаралды 2,1 МЛН
Gizli Apple Watch Özelliği😱
0:14
Safak Novruz
Рет қаралды 2,3 МЛН
Телефон в воде 🤯
0:28
FATA MORGANA
Рет қаралды 774 М.
Мечта Каждого Геймера
0:59
ЖЕЛЕЗНЫЙ КОРОЛЬ
Рет қаралды 1,6 МЛН
Секретный смартфон Apple без камеры для работы на АЭС
0:22
🔥Идеальный чехол для iPhone! 📱 #apple #iphone
0:36
Не шарю!
Рет қаралды 1,1 МЛН