Why can’t they just put everything in a packout box!!!

5/8 is the size of the bolt and “11” is the threads per inch

Bought this a few months ago for acoustical ceilings. Best 3 plane you can get and with 2 of the new targets it's game over. Soooo easy and convenient.

That's real nass like and all, but you been swimming bro? 🤷

I love how you play with your toys I mean tools. People always give me crap for playing with new tools. Happy for you Vince!!! Looks awesome

I sprung for a Bosch version about two years ago...I was really apprehensive at spending money on a tool I wasn't sure I's use much...I've ended up using it a LOT. Tiling, hanging cabinets, etc etc etc...I will definitely check it out!

I have one of these….i LOVE it!. Its way expensive but i would buy it again in a heartbeat

The charger clip 😂😂😂 I Love it lol

Thanks a lot, I've been looking at this for awhile now. I had to buy it thanks to you.

Nice tool. I’ve got the Dewalt version with green led too. It’s so much easier to see than the red led.

The editing cracks me up so much! Well done, informative and entertaining!

Nice! Good to learn that the green lasers can be seen easier! Thanks VCG!

Thanks again for the great information 👍👍. I’m like you about technology, I’m ole school & it takes me longer to grasp the new. 👍👍👍👍keep’m coming, have a blessed day today from Texas y’all 😀

Hi great video could you do one with some layout in mind outside fence posts with a detector. Can you turn a detector side ways for plumbing posts. How easy is the plumb point to use as opposed to a plumb bob with the old transits? thanks

I just framed out a 900 sqft basement using only this laser! Overall I like it. I was using the Bosch version (BSHNGLL3-330CG) for about 3 years prior but broke the mount to it and will sell it as is. This gave me the excuse and justification for matching battery platforms and phase out the few remaining Bosch cordless tools. I pulled my layout from the existing girder and joists-easy! The Pros: super bright laser (although the line is thick up close), very strong magnet 🧲 -it hugged a lally column firmly, laser position lock-for laying out something that’s not level, built-in micro adjust, and lastly-it’s m12! Cons: It’s bulkier than the Bosch, more expensive than the Bosch, accessories are extra $$$, and no Packout-come on Milwaukee!-at least make a Kaizen insert! Bonus: use it to mark out all the ceiling lights and fixture cutouts on the floor (just in case your drywall contractor forgets to cut one out)

I got this laser when it first came out, and it is terrific. I'm in the glass industry and I use it all the time. Always enjoy the reviews, keep up the good work

I too got this very quickly after it’s release. I waited for it to show up at my local tool supply house. Love it. But couldn’t they have made it in a packout case?!?! Suckers like $600 man I want it to go into my packout stack.

Some ceilings installs require a pitch. Its extremely beneficial to be able to use the laser while its out of level

The lock feature is great for when you need a line and can't rely on chalk or pencil or something. Sanding something to shape in a rounded corner or something similar, or for angle transfers for roofs, ceilings etc. It's great.

from what ive read is that when it is on and locked and doesnt run level if more for when you do have to doing something drastic like a hand rail so you can keep that line

This lazer is amazing and I added this to my collection, used it and it blew me away 👍🏼👍🏼👍🏼

I'm getting that. The micro adjustment sold me on it.

This is top of the line lazer. Price reflects that and totally worth it... IF and only IF you are a professional. Home jobbers like myself.. no way. But they have other solutions for us. If you're into remodeling, construction etc This is a must have. Time savings alone makes it pay for itself in no time.

Just seen this on schaedlers bimonthly sale catalog, my recent scrap run I've saved is being used for an 1 1/8 sds plus rotary hammer, this laser is next.

nice laser. I have the USB version (not 360 degree) but for my needs it works great. (I did pick up a spare battery for it). The green is so much more visible than the red. About the only things I don't like are no standalone charger for the USB batteries, and the case... why the heck isn't it packout compatible? It's like those M12-only chargers... a real head-scratcher that Milwaukee hasn't improved this stuff with their own current offereings.

Bolts are measured by diameter, pitch, and length. The pitch is the number of threads per inch. For example 1/4-20 (20 threads for every one inch length of bolt). #10-32×2" ( screw would have approximately 64 threads due to the finer thread cut, and so forth. Thanks for the videos. Btw, I have mostly makita and Milwaukee. In the market for a cordless router, and leaf blower. Any recommendation out of those two platforms? Thanks for the vids!✌

I have the Bosch gll 330 gc Had it for 3 years and love it.

Thank you so much!

Go Vince! 20 years ago, tens of thousands! Now they got 4 plane lasers on Amazon for under $200!😮

I have the same laser by Dewalt, I think I have had it for almost 5 years. It is surprising how Dewalt is way ahead of the competition with new ideas and than Milwaukee tries to improve on them many years later. I bought the receiver for mine so you can use the laser outside, a must have.

Does this have a plumb setting? Ie. point on the floor and plumb point on the ceiling?

Hello again Vince and Vcg Thank you for another Great Video. You guys have the Best Toys, I like it. Again thank you

4:30.. standard hardware for these...👍 Micro adjusting on the tool is a cool feature but for very little money you can buy a nice tripod that you can micro-adjust and do it that way and a lot of these tripods are like $50-$60 good ones... I think I got my Bosch B150 for under $50

Do you know when they will be coming out with the eye to put on the stick or level? I just need that particular component and a tri pod and i'm all set.

How cool would it be if it attached to the utility cart

Looks sweet. I agree the m12 charger sucks but it is rated at 3 amps, same as the multivolt. Still would make more sense for them to include the multivolt in all m12 kit...at least the more expensive ones anyway

Lasers and smoke machines. It’s time to par-tay. DJ Vince is laying down review tracks with specs that thumps the competition.

@VCGConstruction Is the thickness of the beam adjustable or a function of its distance from target? I want one for hanging shelving, art, mirrors, but need a thin line to keep my drilled holes as close to level as possible. Also, thanks for the video…been wanting to see you review this one for a while!

Bought one 2 weeks ago. Love it!

Hey Vince! The LOCK feature is used to protect the pendulum while not in use, by locking it into place. You're welcome :)

2:06 THAT WAS EPYC! 🤣, love it. Yeah, it’s funny how we’re all so used to red lasers and using them and trying to see that darn line, and then the first time a green laser is used, it’s like….WOW, why didn’t I just spend the money and get one sooner, b/c they really are Worth using. If you need lasers on a project that doesn’t involve a small area or enclosed room, green is definitely the way to go; so much brighter and easier to see. Worth the cost and if take care of, should pay for itself👍🏻 Cheers Vince✌🏻

Have to watch and recreate Ocean’s Twelve Laser Dance on KZfaq…brought to you by Milwaukee Tool and VCG Construction!! This is some Mission Impossible action going on 😎

I do tile and use the Stabila pole and laser. Its great but the laser is limited. Just purchased the Milwaukee laser and was wondering how I can attach it to the pole?

It’s the third most expensive tool I own, but man is this far and above all other lasers I’ve used. The fact it pivots around the plumb points with the micro adjust? Milwaukee clearly did their homework about how to do it right. Keep it up Vince! Love the videos!

They are great we have been using them or others like it for a few years in building conveyors in the airports. But as a union millwright in New York thankfully I don't need to supply my own on job the contractor will even though I have 1 myself. The question is why don't they put their products in packout I'd be more likely to pickup full sets instead of bare tools if they came in packout

Great content as always! Vcg!

Box reminds me Of the Digital M12 Laser Levels @0:19 @Vcgconstruction

Wanted to buy this last spring when building shed. checked everywhere even Milwaukee tool could not tell me where to get one. The only problem I have with Milwaukee is finding there tools when I can afford them.

Sweet level, I'm hard pressed between this since I have m12 or sticking with Stabila because well...Stabila. Side note: the thread specs are fastener diameter followed by thread count, assuming UNC type specs. 1/4 x 20 means 1/4" diameter, 20 threads per inch. Source: I'm a mechanical engineer

How does this compare to the HILTI PM - 30 MG? I was looking to get the HILTI, it gets great reviews and is similarly price to Milwaukee. The Hilti is more compact as opposed to the bulkiness of the Milwaukee. My whole tool platform is Milwaukee, so it would fit right in. Maybe you can do a video on both and compare. What are your thoughts?

Just bought the Klein 93PPL 3 plane laser. Great unit for the price of 245. The down side is that they donor have a laser detector available for it. Also bought the 20V Dewalt 3 plane as well. Works great for the price.

AAAAWWWWHH!!! DUDE YOU SHINED THAT LASER IN MY EYES!!!!LOL

Where can I find the camera stand you were using

Very cool Vince Thanks for the video

I have been using mines daily for the past month along with my other Milwaukee green lasers to grid ceiling mounted lights. They have all been great, I've also been using the Milwaukee green laser detector which is great for daylight use at extended range when it's difficult to see the laser lines.

I got one of those. It's amazing. I accidentally dropped it off a lift about 5 feet up and it still works fine. I also got the ceiling grid attachment and the vertical micro adjuster attachment. The vertical micro attachment is awesome but the weight of the laser is so heavy that it pulls the plastic gear away from the track causing grinding when adjusting it. Unless you want to damage the gear you have to lift up on the laser. In my opinion it's a big over sight and very disappointing considering its for a $600 laser with the Milwaukee name on it.

How do I find the M12 charger issue video? I tried searching your channel and came up empty. When viewing on the PC or Roku, the prior video "cards" you point to in the corners are not visible.

Looks nice! Have to add it to the Xmas list and see if I have been nice this year 😉. Also I think you need to add hard shell cases to the worst Milwaukee accessories. How they have not converted those all over to packout by now is a real head scratcher!

Misterr siempre con las novedades para latam

Gotta love lasers, one of the coolest things.

@Vince these work great outside with squirrels

5/8-11 means it’s 11 threads in 1inch. The more threads per inch the more threads or “finer” threads you’ll have

This unit has nice features, but accuracy of 1/8" at 33 ' is not too good. My old deWalt unit is 1/4" at 125'. Botton line is accuracy is paramount.

Got my VCG shirt yesterday!!!!!! Love it!!!

Looked at the Milwaukee multi-line laser but ended up going with the Hilti PM 30-MG multi-line laser. We typically work in large, brightly lit rooms so needed something that can shoot over 300' while using a receiver,,

When the pendulum is locked and it flashes one time every eight seconds to let you know the pendulum is locked that is to shoot control lines at an angle let’s say a handrail for staircase. Both of the laser I have do that one being my Huepar which will only run you about 200$ for a 3x360 green beam with about a range of 100-120ft depending on Ceiling height and natural lighting.

Until my stablia's need replaced...these will have to wait... not to mention, I use a dot laser 90% of the time, which stablia's LAX300's have within their line lasers

I ended up going with bosch, both are very good levels though!

I need you guys to help me figure out a way to get away from the big bulky case and move the laser and accessories into the packout

Lock mode is for running gradients like guttering

I’ve been saving up to get this exact m12 laser

Vince where can I get that milwaukee safety glasses?

Analog kind of man, all the goddamn way, you son of a saint.

I ordered one back in June wanted 4 months and canceled my order and got a dewalt. I'm a milwaukee guy all the way but I couldn't wait any longer

Good job there, Vince.

How heavy is the laser??

How does it look outside?

I've never seen Vince this excited

Can you find us a tripod option for this beast please.. I have the milwaukee tripod# 48-35-1411 and it's terrible for this heavy Lazer. I do not recommend that and would like to know of one heavy enough to hold this Lazer without it tipping over.

Are there 2 brackets missing in that case?

Is this laser level better than the dewalt version?

Vcg notification gang checking in!

1/4-20 threads. 1/4 diameter with 20 threads per inch. 5/8-11 threads 5/8 diameter with 11 threads per inch. A fine thread would be 5/8-18. 5/8 is the diameter with 18 threads per inch.

Makita have the same and its also perfect

Leica Lino lg6 best self leveling laser tool kit in the business. But the Milwaukee is also great if you've already are on the red team platform.

Have the M12 non-360 version. It's awesome, way cheaper. Wish they had a small hard case like the ones that come with the DeWalt lasers. That case is obnoxiously large.

Could you review a huepar laser 360 laser?

Does it come with the tripod??

The locking is for 45°layout on the wall

5/8" - 11 (Threads pre inch)

I'm STUPID for NOT subscribing earlier!! I am now a genius! Aimed that laser at that like button.

I love it vince but as always the m12 laser is only just coming in to the uk 🇬🇧 and at a price but I will say as a lot of other people saying why is it not in a packout come on Milwaukee get your tools in packouts as packouts ARE the BEST thanks vince stay safe 👍👏👏

It's an ideal tool but it's allot of money for someone that isn't a tradesman

Laser is nice, its bulky, debri gets in the magnets and its a pain to get out, i still use my PLS more,

Look pretty nice, but what I been waiting on is a cordless roofing gun from milwaukee. Would it be possible for you to ask milwaukee if they are planning to release a cordless roofing gun, and if yes when would it be? Much appreciate and keep up the great content.

Can anyone tell me the difference between the 3 plane and the 4 plane ??

Guess we're not getting an HD live stream today.

Very cool. 👍🏿

I was going to buy this as I think Milwaukee make quality products. But think it is slightly too big and awkward for my application. So I went for the more compact Geo fennel at around the same price range. And apparently are made and owned by Leica .

I have one digital request, Vince. Can you put the links to the best place to buy these awesome products in the description? Much appreciated and KUTGW!