Sometimes you find accuracy and sometimes it finds you... and sometimes you find each other, that's when things get really weird... Patreon: / urituchman Instagram: / urituchman
Пікірлер: 282
@LaserGadgets2 жыл бұрын
First thought: Sounds ALMOST too normal for a Uri video!
@thebusbums28252 жыл бұрын
I also thought this
@TheHailacopter2 жыл бұрын
Expected him to make it resemble a can of beans or something.
@jaredknapp8886 Жыл бұрын
He did end up making it a can of beans later that week.
@dan__________________2 жыл бұрын
It might not be the backplate causing the wobble. When you tighten the nut on the motor shaft it will not be exactly square to threading. This will result in the backplate not pressing evenly against the stop behind it. This is usually fixed by using self centering washers which are essentially two washers with opposing conical faces. These conical faces will slide against each other and compensate for the out of squareness of the nut.
@tuffymartinez Жыл бұрын
Ya got that right Dan....TM
@antoniocarlospereira3753 Жыл бұрын
Parabéns muita saúde
@marcellorossini5822 Жыл бұрын
I think the stop itself is not flush at all. Unfortunately I think he didn't flat the head on that first lathe cut. :-/
@bradleytuckwell48542 жыл бұрын
There’s something about adding brass to a build it adds class. It’s like the James Bond of all the materials.Anyway thanks for sharing I always enjoy your content
@PatrickOliveras2 жыл бұрын
Less than a minute in and you have already just eyeballed the damned diamond wheel alignment. Among engineer-artisan channels, you are one of a kind, Uri. Never change.
@joeo63782 жыл бұрын
Like a Stefan Gotteswinter's long lost eccentric twin brother.
@ArtisticEndeavors2 жыл бұрын
Splendid! Although I think it really needs an engraved pigeon on it somewhere. ✌🏻🎨☕️
@SAHBfan2 жыл бұрын
Surely, surely, it will have, somewhere? We just didn’t spot it, I expect…
It is such a pleasure to watch a master at work. Your abilities and ideas are unmatched on KZfaq. Thank you Uri for sharing.
@CookieQuantum2 жыл бұрын
That was wonderful, but the drill press sections were pretty scary. Maybe some drill press clamps would be a good idea for a future project, perhaps with some brass.
@robwgeorge2 жыл бұрын
Yeah. I puckered up a few times.
@cncgeneral2 жыл бұрын
And less stopping the drill with his hands! 🙃
@scurvymcdiggle27412 жыл бұрын
Let's start a petition! We want drill press clamps!!
@thedivisionbell2202 жыл бұрын
It does look scary, but one can get pretty fast at pulling their hand away when the bit starts spinning the work peice, especially considering drill presses are set at lower speeds for metals. You can see he used vise grips after, which is a very good way of holding small peices that would otherwise be too small to clamp to the work surface.
@tiporari2 жыл бұрын
You only have to get whacked a few times and then you learn. Hopefully with all your fingers intact. I used to tack weld by closing my eyes in a hurry. Sandpaper eyeballs taught me to use the helmet even when lazy.
@The.Talent2 жыл бұрын
Uri Tuchman is the Bob Ross of the maker-world. Every episode is full of “oh my gahd I made a little mistake there. And there. And over here too”, but somehow each piece comes out looking amazing. Imagine how it would be oh he didn’t make any happy little accidents.
@willd65152 жыл бұрын
I love the fact you also show the trail and errors. I´m a tinkerer myself and a lot of time is going into figuring things out.
@robertlangley2582 жыл бұрын
It is such a pleasure at watching you design and create your works of art. Your silly side is wonderful and your so creative. I’m very happy I ran across your channel I guess almost two years ago. Just love all your creations Uri. 👍👍👍
@emmalouize Жыл бұрын
I love this channel and I appreciate everything you do. I understand and appreciate your processes and all the little quirks that I feel I have in common as an artist and creative myself. I love that you show your real self, the happy creative. I like to think I have a broad knowledge over many areas that allows me to think in a way that nurtures and drives my creativity. But you are on a whole other level. You encourage me to continue learning and teaching myself. Everything you do is so creative and I love the new Pigeon studio soundtrack 😊 it’s awesome. Love to you and your family from New Zealand 🇳🇿❤️
@hectatusbreakfastus61062 жыл бұрын
Your videos are always a joy to watch. Your creativity is always inspiring.
@gyrogearloose134511 ай бұрын
Uri your skill and ingenuity never ceases to amaze me. What you do with your limited tools is very creative and inspiring. And I like your good spirits and sense of humour very much. What else can I say? Oh ... just keep your workpiece secured for Gods sake! And save your fingers and other bits! Thanks for sharing, best wishes on all your projects.
@ussweeneyd2 жыл бұрын
I love your enthusiasm ! Great result.
@dominicjbealing49892 жыл бұрын
Truly a joy to watch you work
@forge202 жыл бұрын
The brass nuts don't work because the lever arm of the tool post can act against the thread. Even using steel bolts will not fix this, I think. Designs similar to this that work use a pivot pin and then clamp the two mating faces together, but have an interlocking pattern on the mating faces so they cannot slip. Perhaps a hinge pin combined with a series of pin holes that set the arm at specific angles?
@urituchmanpigeon2 жыл бұрын
Your right, perhaps I'd make the middle piece again, with pin holes and such.
@fasousa47982 жыл бұрын
Using a knurled pattern like on a file on the mating surfaces should suffice
@frankierzucekjr2 жыл бұрын
@@fasousa4798 exactly, that will give enough friction I think.
@frankierzucekjr2 жыл бұрын
@@urituchmanpigeon I really enjoy your videos buddy. I cant wait to see what you make next. I'd love to see you do more of those figurines that you carve and that move.
@jackplant92322 жыл бұрын
@@urituchmanpigeon a friction disc would do the same, you could make a simple one out of Emery paper
@TheMrWoodsman2 жыл бұрын
Fantastic engineering, always a pleasure to watch your videos.
@stefanbadass53572 жыл бұрын
BLOOD!...SCARS! ...My God The Man Suffers for his Art. Excellent as always. Keep on keeping on Uri
@constantinoscreations27983 ай бұрын
You are a very talented and also an extremely funny guy. Your videos are a joy to watch. Keep it up!
@viorsa82002 жыл бұрын
Excelente tutorial Uri , como de costumbre , es un placer verte trabajar con las manos , cuidarlas mucho , gracias por compartir tanto ingenió y conocimientos , un saludo cordial y por supuesto un gran like desde Narón (Galicia)🤓 🔝
@wayne6318 Жыл бұрын
What a brilliant idea and a great tool
@beebop98082 жыл бұрын
I don't really know why but I found your little video quite entertaining. Thank you for the show good sir!
@samanthadean10832 жыл бұрын
Uri, this turned out amazing!!! ❤️❤️❤️❤️❤️❤️ But one piece of advice? Breathe! You were on high speed through the whole video!!! You can catch your breathe now!!!
@acraftman28232 жыл бұрын
You need to play the theme to jaws as you slowly pan towards the drill press
@thalesbarbosa8535 Жыл бұрын
Great job, I loved the creativity
@kelseywatson19742 жыл бұрын
I've been planning to make a diamond grinding setup on my lathe. I was planning on making a plywood rest, but now you have me thinking I should step it up 🤔 great design
@paulcohen1555 Жыл бұрын
I like the way he is using simple hand tools.
@buttersstotch6752 Жыл бұрын
Custom brass knobs had me. Like FFS is he lathing them smooth BY HAND *subscribing
@simon92642 жыл бұрын
it's nice to see tat you drop things as well as me
@SteveC382 жыл бұрын
Nice Job, Uri!
@terrortorn2 жыл бұрын
"Lovely Jubbly". someone has been watching OFAH!
@RestorationAustralia2 жыл бұрын
Great idea, well done.
@Whitefirekith2 жыл бұрын
Uri, you need to look into the Harold Hall books for lathe and mill home made gadgets. Then you can embellish them with your characteristics. I think it would be a real benefit to you in your shop.
@patrickosullivan43542 жыл бұрын
Ooh Uri Tuchman how I long to see A video upload presented by the thee I know for certain it warms my heart Just watching you go about creating art
@danmorgan86322 жыл бұрын
Thanks for the video Uri, I'm inspired to turn the left hand end face plate sander on a wood lathe into diamond wheel. I suggest you make or buy vice for your drill press next !
@leemichel8199 Жыл бұрын
Speed control would be a great addition 👌 👍 👏 🙌 😀. God bless you and your family 👪 🙏 🤲... Lee
@visiblesolarsystem61432 жыл бұрын
Nice work and good ideas.
@motobenbh47222 жыл бұрын
Bravo Uri
@jimgreen4504 Жыл бұрын
Inspector Clouseau in his hobby shop. Well done mate.
@raywicks893 Жыл бұрын
Pure craftsman 👌
@luzern10002 жыл бұрын
Super interesting video, but I have a question. Why didn't you set the support plate higher, i.e. above the axis? Then you would have the entire width of the grinding plate available, and it would certainly be less dangerous for your fingers
@stevebettany87782 жыл бұрын
Always a pleasure.
@Paullyb792 жыл бұрын
I have the same set up in my shop. I have 3 registration pins and have the disc mounted on a plate with magnets. Can go from course to very fine in seconds.
@55ATA32 жыл бұрын
Great to see the new video, some stop blocks for the drill press might make drilling have less blood being loss to drill stuff.... Be safe and hope to see more videos this year...
@pjhalchemy2 жыл бұрын
Love the build of the table and miter fence! You are a maestro at this kind of build!! 2 issues: first, use conical or cup and seat washers for the back plate and lapping disc as @Dan Letkeman says below. Once that is done you could use your miter fence to true the running face and edges of the back plate with sand paper and a square block. Second, most grinders run at 1750rpm which is way too fast for lapping disc and will wear them out quickly. If you can find an inline speed controller for the grinder to get the speed down to around 800-1000 it will help a lot. Typical lapping plate systems actually spin around 4-500rpm. Thanks for the fun build!!
@88njtrigg882 жыл бұрын
Oh..my.. this is better than perving. I'm excited.
@lacaver64 Жыл бұрын
Yuri one thing when you are cutting with the saw CUT in the right side not in the left side because you can shock you hands at the table. In the right side tour hand go to the Air and can not shock your knockles good video yuri
@bearworxstudio15672 жыл бұрын
Success of a project is directly proportionate to the number of "oh my god" moments you have in making it. For good, bad, or scary.
@guustflater92322 жыл бұрын
Hi Uri, I assume you've already checked the axle for runout. It's a pretty common issue with these small bench grinders.
@Tarps-Basha-Poncho Жыл бұрын
I made a similar thing to you with a mount that took every grade of diamond disks for marble top finishing. Mine was for polishing and cutting Opals, I also made a water feed gravity fed with a tap.
@Gabrulo_knifemaking2 жыл бұрын
There is a word in italian that describe you very well: pasticcione. I can't find the translation cause the meaning is not so negative as the english words, but even if you are a pasticcione, you are always dead precise, i can't understand how you manage to build perfectly functioning tools like this🤣 is always a pleasure to watch your videos
@NiklasGisi2 жыл бұрын
As always a very delicious video you've made 👌
@roehle99622 жыл бұрын
yes quite splendid, indeed 🥸🕊
@PAINFOOL132 жыл бұрын
Always a Pleasure 👍🏻
@martinhorner6422 жыл бұрын
Using a chasing hammer to pound a center punch is the definition of Uri Tuchman (not because it was wrong or bad, but because he can make that work =)
@Bertoos82 жыл бұрын
Now yes, friday! 🙌🏽👌🏽
@machinist_matt2 жыл бұрын
Very nice! But it almost seems too conventional for a Uri Tuchman project! Why isn't it shaped like a pigeon or pork chop or something? 😄
@ParsMaker2 жыл бұрын
nice work
@TheKnacklersWorkshop2 жыл бұрын
Nicely done Uri... an enjoyable watch, than you
@falcfire30932 жыл бұрын
Very inspiring!
@NarcissistMargarine2 жыл бұрын
Pleeease invest in (or make) some clamps for your drill press. I could hear the echoes of my industrial art teacher scolding me every time you used it lol. Great video as always though, of course
@Gorn1712 жыл бұрын
this second zoom at 3:16 cracked me up as you were playing somehow with my expectation that it will spin again :D damn i love this editing
@shurdi32 жыл бұрын
Uri just going in with the fat chips definitely got me all puckered up
@jdstar63522 жыл бұрын
Bravo! Also, you need a drill press hold down clamp.
@briggsbughouses62912 жыл бұрын
I'm glad to see you have a Taig lathe, they are flexible little machines that really lend themselves to shop made modifications too. Looking forward to seeing your projects progressing!
@thomasarussellsr2 жыл бұрын
Gotta be able to sharpen that carbide... Well done Uri. The wobble could also be in the washers, the shaft itself, or play in the grinder motor. Most bench grinders have some sort of play/run out. The more expensive ones have less. There are beveled washers you can buy for the mounting shaft then you his have to play with a pair of washers to get that perfect adjustment to true your grinding wheel, or in your case diamond plate. Bench grinders aren't really designed for face plates, but for edge wheels. But a true running shaft is a true running shaft. Good luck.
@robertberger86424 ай бұрын
Good video!
@MikelNaUsaCom2 жыл бұрын
good progress... accuracy is a journey and not a destination... =D
@marbballz2 жыл бұрын
Uri great tool, hope you can fix the squareness issue. Also hearing you say lovely jubbly made me chuckle.
@beaverc28842 жыл бұрын
Small projects like these are my favorites. If you get them right the first time it's so satisfying but if you need to remake them because they are to small or to big the "how to make" process and the "don't do thats" has already been done so all you have to do is scale up or down. I have to admit I have copied some of the things Uri has made. 🤫🤫 love this channel.
@zeusdeux2 жыл бұрын
Years after hanging out at truffle pig, I’m still here every week. God this is fun content!
@jpsimon2062 жыл бұрын
Melamine works quite well as a backing disk. It is surprisingly flat. In fact I've seen quite a few people successfully lap parts using diamond paste on a bare melamine wheel! Seems to work just fine although I would be concerned about moisture. I tend to dip parts in water rather often while grinding
@ralphrohr2 жыл бұрын
There he goes again: the god of brass!
@daveticehurst41912 жыл бұрын
Uri, Check the shoulder on the bench grinder, sometimes they are not nicely machined. The slightest of burrs will throw that 7 or 8 inch diameter out quite a lot at full diameter. Your original backing plate may still be fine to use. Use a fine flat hand file and use the NON safe edge against the grinder spindle shoulder, rotate it by HAND to check for burrs. You may also find that the shoulder has a radius, so your backing disc will need a slight bevel to the hole to miss the radius. Good Luck fixing it. Regards from Australia.
@johnhall845510 ай бұрын
Keep the table closer to the disc to stop anything being dragged down into the gap…nice work…👍
@nickashby47452 жыл бұрын
Neat! Don't worry about the guard..diamond doesn't cut & the wheels unlikely to explode!! Re the flat lap..the grinder flanges might need truing to the grinder spindle (standard grinders aren't precision kit)!
@zonnenschein-iy6sf Жыл бұрын
to even the back plate i would put three spots of cusi with a tig welder and file them until the weel runs centered. you can also drill a larger hole into the disc and make a bronze bushing spacer and try to make the bushing more precise. if the disc is not flat you can sand that to be flat on a flat surface.
@user-tz8ui5gj8d Жыл бұрын
Благодарю! Все сделано отлично! Однако, прийдется доработать нижнее крепление, чтобы исключить проскальзывание между подвижной и неподвижной частями, осевого зажима недостаточно. Обычно, для таких целей, используют такую-же конструкцию как Вы использовали для установки горизонтальных углов заточки. Есть и другие варианты но они потребуют больше деталей, и в конечном итоге затруднят настройки вертикальных углов из-за люфтов в соединениях. Успехов Вам!
@wayneshirey69992 жыл бұрын
Unnecessarily exquisite and oddly satisfying as ususal.
@SirPotato892 жыл бұрын
Hey Uri, haven't you thought about doing a mechanical clock? You have the knowledge, as well as the tools! I'm pretty sure that it would look pretty great.
@frankierzucekjr2 жыл бұрын
You're slinging some chips now buddy. Lol. I really enjoy watching you make stuff. The comedy is a plus lol. Hope you're doing well buddy. I bet you miss your cats walking around what you're working on lol.
@colemine70082 жыл бұрын
There are special washers that take the wobble out, they are spherical, I believe? They come in sets of two and nest together and compensate for things being off.
@user-fp2cr4lz8m2 жыл бұрын
You are amazing!
@sacriptex58702 жыл бұрын
hey Uri try a plastic backplate to suport the diamond disk, because you can true it up using a bit on the machine itself then glueing the disk
@jackplant92322 жыл бұрын
If you put some sort of friction discs between the sections of the support arm, the screw won't need to be as tight to get it to stay in position, so you may be able to use your thumbscrews.
@kiwishamoo64942 жыл бұрын
Very very nice
@Nono-hk3is2 жыл бұрын
Supercut of just every time Uri says "Oh my god"
@infernaldaedra2 жыл бұрын
What you need is some clamps lmao. Protects the fingers
@watergeting858610 ай бұрын
Impresive
@lindboknifeandtool Жыл бұрын
Diamond at high speeds deposits carbon into the sharpened piece. This is mostly experienced in industry but I’ve heard of guys power grinding their knives with diamonds and it ruining them. The ideal abrasive material would be CBN or Cubic Boron Nitride, but if it’s any harder to get than diamonds then I wouldn’t worry. Keeping things cool and or lubricated can cut down on that quite a bit. You’re a natural toolmaker Edit: I thunk you’d have fun with a 0.5-40 micron diamond paste pack. I got one from venev for like $12 and it makes polishing hard materials a breeze.
@winfriedbanzhaf1067 Жыл бұрын
You are good!
@johnjude2685 Жыл бұрын
Agree it can improve
@ShevillMathers2 жыл бұрын
Put a piece of copy paper between metal surfaces to give much better grip and locking. Greetings from Tasmania Australia.😁🇦🇺🦘
@jacoklopper47722 жыл бұрын
I love your commentary when you let something fall etc. 😅
@whitehouseummahh97252 жыл бұрын
Love me some you, bird man!!!
@migalito19552 жыл бұрын
I kind of lost touch after your son was born and you kind of took a break from video making. Good to see you back. Seemingly a nice shop too. I think the last video I had seen was the live stream with your wife's friend acting as more or less host that then ended with the camera seemingly going mad on its own. I like your mini lathe. I have a Shopsmith wood lathe that I enjoy using and an old Oliver small metal lathe from around 1900 that needs converted to V Belt and they certainly are enjoyable to utilize and it shall be interesting to see what you output with yours.
@jumpingjacks55582 жыл бұрын
Very impressive. Great video. Question: Is the sharpener spinning to fast to sharpen your tools? I always thought they were much slower.
@moonolyth2 жыл бұрын
Excellent build friend, I'm sure there are things to update. A real backplate will do wonders for true flatness, no wobble. I would not add a safety guard ... will only get in the way. but always try and hold small spinning parts with a vice grip if possible... too many safety nazis. I'm sure you have things under control. Also, I noticed you have the other end of the motor shaft idle, not in use. I rebuilt a Grinder and replaced one side with a (Motor Adapter Arbor 1/2-20 Threads Fits 1/2" Motor Shaft or Spindle) Look on eBay..$24 bucks. Make sure you get the correct right or left threading for this. Then I added a Drill chuck!!! Now I can use all sorts of adaptors for diamond, Wire brushes, and even 4.5 Hand grinding disks. And I can place a drill bit in it or even sharpen one. Works so well You should try it. In the US the Adapter Arbor is about $24 a chuck around 12-$14. The chuck may not be perfectly centered, but even then if you leave the grinder motor on its rubber legs this will compensate and center the chuck very well... I use this little junk motor all the time now. It is small enough I can stop the chuck by hand but it still has some power. In a shop like yours bench jewelry style, I can see this would come in very very handy. You won't regret the chuck adaptor. Sir.
@NoBug40410 ай бұрын
Perhaps you should make a vice for your drill press.
@Keelsman2 жыл бұрын
Beautiful work! And a pleasure to watch. Thank you 🥰