I made a sharpening tool that makes the drill bit sharper than a new drill bit. This tool will be distributed free of charge to those who purchase the Sander Stand Plan. #how to sharpen a dril #drill bit sharpener #how to make
Пікірлер: 65
@user-dz1nm6ed4y3 ай бұрын
Нельзя так затачивать. Такие диски не предназначены для боковой нагрузки, поскольку сетку защитную стачиваете, а ещё они гнутся при надавливании, что на видео и видно. Полноценный заточной диск, но убавить до нужной скорости вращения обороты у УШМ, чтобы не превысить допустимую угловую скорость вращения камня. Работать с торца диска, а не сбоку. Или алмазную чашку, что попрочнее будет.В общем задумка неплоха, но требует доработки. Заднюю кромку сверла нужно сгладить, а затачивается режущая часть.
@user-fi9iq1vo6m3 ай бұрын
И что, под каждый диаметр свёрл делать эту приспособу? 😂😂😂
@user-wl8sr7ef5g3 ай бұрын
Мой дедушка говаривал, - "а где ручка?" Зачем? А что-бы закинуть подальше удобно было!..
@Las_stick3 ай бұрын
thank you, you are the best
@desbravatube3 ай бұрын
Isso aí parceiro, show de bola Att: Weliton Marks - Canal Desbravatube
@robinmarwick19823 ай бұрын
A lot of negative comments from people who claim to know better. I was pleased you refrained from the lunatic practice of removing the disc guard from your angle grinder.
@Alvawelding20Ай бұрын
Thank you very much
@mikethomas30693 ай бұрын
The included Angle for a twist drill is 118/122°
@tomegloff39943 ай бұрын
This drill bit does not have any back relief The cutting edge is shorter than then the tail It would be next to useless.
@CreativePassion883 ай бұрын
good tips for life
@user-pj7co3jp4j3 ай бұрын
2 одинаковых уголка не будут так ходить ( в притирку) надо скачивать грань у верхнего, или будет зазор и верхний будет гулять.
@user-ud1sy1ib1s3 ай бұрын
Под каждый диаметр своя приспособа?
@AbdulbositHomidjonov3 ай бұрын
👍👍👍
@user-uv5vt6eb2c2 ай бұрын
А как насчет заднего угла режущей кромки.
@user-tw6ne6uu3f2 ай бұрын
Пробую, каким диском пользуетесь,
@drolingink3 ай бұрын
Success! For only 3x the cost of a new drill bit and 10x the duration it would take to go buy one; you too could have fresh, sharp, and slightly shorter drill bits! 😂
@robinmarwick19823 ай бұрын
Do you throw away a chisel when it gets blunt? Yeah a jig takes time and money to build but once it's done you've got it. Could have had it half made in the time it took to make your ridiculous comment.
@drolingink3 ай бұрын
@@robinmarwick1982 man sharpening a chisel is one thing, this is something totally different
@robinmarwick19823 ай бұрын
@@drolinginkno...they're both tools that make holes in things. Got my first set of drills 20 odd years ago; true enough they're shorter than they were but so are my chisels. Monumental waste throwing away a drill when it can be sharpened.
@user-mh9vv5lw8n3 ай бұрын
У меня ученики без опыта , на глаз на алмазе и то лучше затачивают
@thomasheighway-bg8rr3 ай бұрын
Dangerous use of slitting disc!!!
@vernonwright88863 ай бұрын
Cutting disk's are not designed for use in grinding. They can disintegrate. Too dangerous for me.
@antoniobragancamartins31653 ай бұрын
This way it don't drill neither butter! The attack angle is wrong and it's overheating!
@ronaldpatton59062 ай бұрын
I can sharpen a drill in 30 seconds doing it by hand . 40 years as a toolmaker.
@davidshumski4629Ай бұрын
With the cutter wheel? I do.
@user-iu9mq9oc3y3 ай бұрын
Да бред какой то видно, что люфты на уголках большие
@michelastegiano7442Ай бұрын
c'est mieux que rien, mais pour tout outil de coupe, en plus du tranchant il faut un angle de dépouille ce que ne fait pas votre système.
@user-yz7we7hv1c3 ай бұрын
Drill a bit in 30 seconds but takes you 4 hours to build the tool!
@clivehall71182 ай бұрын
😊😊😊😊😊😊😊😊😊😊😊
@clivehall71182 ай бұрын
😊😊😊😊😊😊😊😊😊😊😊
@dantixc18173 ай бұрын
Time and materials way more than buying some more bits😂
@BoJ-gn3iv3 ай бұрын
NO slipp angell thats why its overheating
@JORDAGAMA2 ай бұрын
LOS TALADROS NO SE AFILAN,LAS BROCAS SI.
@jean-charlesmarty2982 ай бұрын
Bonjour, lorsque l'on ne sait pas affûter un foret à la main, on s'adresse à quelqu'un qui s'y connait.
@adrianvlaicu77633 ай бұрын
D= 4,5.6.8 10????
@stefanklasovity16542 ай бұрын
Pre magorov 😂
@lawrencemacd633 ай бұрын
That’s a long 30 seconds 🙄🙄
@user-zh3hw3wg5v13 күн бұрын
Полное враньё. За одну установку сверло заточить невозможно. Необходима обеспечить затылование задней поверхности.
@user-sm5uq7jy6u3 ай бұрын
Купи новую и всё,...
@nickyu287Ай бұрын
Гайки тільки заважають, все одно, на око.
@user-tb4dh5pg3xАй бұрын
о ко ко))
@user-yz7we7hv1c3 ай бұрын
So you need to build a jig for each size drill????? This is so damned stupid. Just go sit and buy a bid sharpener for 20 dollars.
@tomthompson74002 ай бұрын
I sharpen them in 3 seconds without a silly tool
@cvele6663 ай бұрын
That's not 30 sec
@pjcoetzee47323 ай бұрын
Dont look sharp when driling
@user-zu4qf8tf6pАй бұрын
Я точу свёрла секунд за 20. А если у тебя руки из жопы ,то можешь ещё пять приспособ сделать ,не поможет .Ты крутишь сверло на котором видно обратный угол заточки.
@user-ne2lt7fe8xАй бұрын
Viel zu unpraktisch,schleife ich von Hand besser und schneller 😛
@olivierblochet5720Ай бұрын
Mouay... Bof 🙄 Il y a plus simple et plus efficace
@true51883 ай бұрын
Totally wrong if that drill was sharpened correctly then you drill something the steel spirals shavings should came out both sides of the drill when drilling . Never use a cutting disk and grinding on the side of it . Use a grinding disk .. clearances of the drill aint right and thats why you force the drill in to the metal . Never hold the job by hand and then drill it . Use a vice or clamp it down . No engineering knowledge
@robinmarwick19823 ай бұрын
That's what I like about KZfaq always some keyboard warrior to pour negativity on someone else's work. Granted safety issues holding a work piece by hand while drilling it. The fact the guy produced a pretty reasonable jig somewhat contradicts your remark of 'no engineering knowledge'
@davidshumski4629Ай бұрын
Why doesn't the cutting disk say you not sposed to grind with it?
@user-fp7ze5fp5gАй бұрын
Видимо никогда у криворуких не кончатся видео о заточке сверл с придумыванием разной хрени. Вы на свои руки посмотрите,откуда они растут. Я ЗАТАЧИВАЮ СВЕРЛА ДЕРЖА В РУКАХ ОПИРАЯСЬ НА ПОДЛОКОТНИК НАЖДАЧНОГО СТАНКА С КРУГОМ МЕЛКОЙ ЗЕРНИСТОСТИ.