Electronic Accelarator Pedal Repair

Electronic Accelarator Pedal Repair - Astra H

Рет қаралды 245,111

3 жыл бұрын

#astrah #astrahpedal #electronicgaspedal
From time to time my Astra H throws out some accelarator pedal related errors. Same it did today, so I decided to finally open the accelarator pedal and inspect what's happening inside.
Error codes were: P1120 and P1122.

Пікірлер: 80

@kentmccroskey3712 Жыл бұрын

Contact cleaner, never rub your finger over the resistive track like that, the acid/oils in your fingers will now wear that part even faster than before. spray contact cleaner on both the pins and the strips, and wipe gently with a lint-free cloth. Also, mark where the screws are in the casing before removing the screws, otherwise, you will need to make sure you can retrain the pedal. most cars have a retrain mode activated via odbII, if you don't retrain and you don't screw it back in exactly the same position as before then the resting position will have a slightly higher or lower resistance than before.

@joeseda8102 Жыл бұрын

Did same work on a car. I recommend using an INK ERASER to very lightly clean the surfaces where contact is made by the small contactors. You have to do it very lightly to just remove any small imperfections in the areas where the contactors make contact. I also used 90% alcohol to clean the parts before reassembly. Car ran perfectly after that!

@miticamunteanu2945 7 ай бұрын

Multumesc frumos pentru informații și va doresc tot binele din lume mitică la toate videoclipuri

@gregdenman2342 7 ай бұрын

Fantastic camera work, very easy to understand

@mrrobertwolfiii1079 Жыл бұрын

Appreciate you helping me finish up

@skydiver4959 Жыл бұрын

Thank's for this, I'm going to try it on my Malibu.

@waleriy116 2 жыл бұрын

За 12 лет работы диагностом-автоэлектриком, я ни разу не встречал неисправность педали акселератора, но всё бывает в первый раз. Гораздо чаще, ошибка по педали имела причину в разъеме UEC, (центр подкапотной электрики). Окислы на контактах разъема, на глаз их не видно. Иногда достаточно просто снять и одеть разъем. Для профилактики побрызгать WD-40. In 12 years of working as an auto electrician diagnostician, I have never met an accelerator pedal malfunction, but everything happens for the first time. Much more often, the pedal error had a cause in the UEC connector, (the center of the under-hood electrics). Oxides on the connector contacts, they are not visible to the eye. Sometimes it is enough just to remove and put on the connector. For prevention, sprinkle WD-40.

@SJSOmar 5 ай бұрын

This helped a lot as the sensor portion is almost the same as a Saab 9-3s

@vpalos 2 жыл бұрын

Great clip! You helped me do the same to my Opel Zafira A accelerator pedal. It was sometimes losing acceleration and was lagging behind (not responsive enough). Everything was fixed after I cleaned it. Thanks!

@icku 2 жыл бұрын

Glad it helped!

@omnilife6660 Жыл бұрын

😢

@mp4338 Жыл бұрын

You forgot to sign before opening the cover because the screw holes are ovales. After close the cover you must to follow the sign.

@nasrahmed6236 11 ай бұрын

Great explanation thanks alot

@balonpromosibalonesia9956 2 жыл бұрын

where can i buy the parts? can you provide the shop link?

@POM4ALLSHORTS 2 жыл бұрын

Great video very informative thx

@icku 2 жыл бұрын

Glad you enjoyed it

@halfpack69 Жыл бұрын

Why did you not reclean the board after you put your thumbs on it? I NEVER chance touching any metal part of the board, unless I clean it after touching it. Better safe than sorry.

@joehoward6664 2 жыл бұрын

Just what I was looking for, thank you, now I will try it and see if it works for me

@icku 2 жыл бұрын

Best of luck!

@avongard1356 Ай бұрын

Did it work? I have the same problem.

@akashluthra9752 2 жыл бұрын

My swift 2009 diesel accelrstor sensor is not working. Can it be repaired. I got it checked from maruti workshop. They don't have this part I'm their store

@EhButU 3 жыл бұрын

Very good - did you repair work - or did you replace part for a new one ?

@icku 3 жыл бұрын

It worked - problem reseolved.

@paulkomn946 2 жыл бұрын

i did exactly this procedure with my opel corsa c and the light with the spanner didn't open again.

@user-du5lt5ij7h Ай бұрын

Thank you for this,I love it.And I understand.

@icku Ай бұрын

Glad it was helpful!

@StratosAsa 2 жыл бұрын

Great video thank you!!

@icku 2 жыл бұрын

Glad you liked it!

@marco45rj 2 жыл бұрын

These black tracks are graphite printed. They are applied in volume controls of various electronic devices. They are delicate. If they show defects in acceleration, change it soon, as the lanes are unrepairable. OK!

@Hi-Tech-Ray 2 жыл бұрын

I agree and I don't think it was wise of him to add tension to the wiping contacts either, This is also a common problem with the Technics SL1200 series turntable pitch controls!

@djokovicboris1162 2 жыл бұрын

Tak treba kúpiť nový? Auto ide ale keď sa šlapne na plinovy pedál tak reaguje ale veľmi málo.Alebo vôbec. Ide na voľnobeh. Je zlí pedál?

@marco45rj 2 жыл бұрын

@@djokovicboris1162 Pri každej práci musíte mať pozorovanie na overenie problému. Takto sa to ťažko hodnotí. Odneste to automobilovému elektrikárovi. OK

@zarularif5466 4 ай бұрын

I will try it to proton persona if it works.. I will update later.. Tqtqvm sir for your video.. Looks more informative and helpful

@sehpengpng7631 Ай бұрын

Kalau cuci plate elektronik paddle sensor , dapat pakai elektronik cleaner ?

@nicolasfremont Жыл бұрын

Hello what was your ODB error message please ? I do not have any error message but my ODB show me a 16% value when the motor car is just switched ON. I think it is because of the "slow motion motor "...what is your opinion Sir ? Thanks you

@crusinscamp 2 жыл бұрын

Very good video. This what I was looking for. Has the problem occurred again?

@icku 2 жыл бұрын

Nope, its working like charm for now.

@Flowerchild778 2 ай бұрын

@@icku A question: Did it need to be reset after this?

@waelawad6566 11 ай бұрын

V good work

@user-wt7wl8qn3f 8 ай бұрын

OK HE CLENED IT BUT WHAT WAS THE CAR PRBLEM DOING THIS DO I HAVE TO RESET IT AGAIN OR JUST PUT IT AND WILL IT WORK OR TAKE IT TO DEALER SO THEY CAN RESET IT AGAIN PLEASE REPLY THANKS

@lastservant Жыл бұрын

Hi AllHandmade, does your acceelarator pedal still work after you did this? Please give me a reply and thanks for sharing, great job.

@icku Жыл бұрын

Yes it's still working. I didn't expect the repair to be such success.

@johngibson4641 Жыл бұрын

@@icku,, ok thanks for awesome video you put on KZfaq. I have a gmh Holden Commodore sv8 5.7litre V8 here in Australia. It is going into safety mode yet its not throwning any codes when it goes into safety mode. I have been told by heaps of other people and other mechanics that it may be a pedal could be the issue as this was the first fly by wire that holden ever made and the pedal was a huge problem. I do luv the car as i bought i from my mums inheritance and luv driving it but due to it going into safety mode it is getting annoying to drive and this goes into limp mode anywhere it feels like it (but mainly at bus stops though , haha) and can be very embarrassing too. Do you know where i could seach for the part or could give me an idea on what part number to chase up so i can fix it. Thanks in Advance and Cheers from John , in Australia.

@icku Жыл бұрын

@@johngibson4641 If you can find your car here: 7zap.com/en/catalog/cars/

@danielntuli3313 4 ай бұрын

Hi, I own a 2003 vw sharan 1.8t,accelerator is very hesitant and slow, do I have to clean it as shown on the video but with electrical parts cleaner?

@suatkaleli5075 2 ай бұрын

good info

@ivanthebig 11 ай бұрын

So, did it work?

@faisal3374 2 жыл бұрын

If electronic accelerator pedal have play (loose gap) then it will effect the fuel average or not?

@icku 2 жыл бұрын

No, it won't.

@SifisoMaphalala-vh3zs 2 ай бұрын

Toyota Quantum 2.7 petrol eccelarate sensor how to replace it

@octavian5548 7 күн бұрын

1.7 101 cv zth?

@KOSTSAV68 2 жыл бұрын

WD-40 Specialist contact cleaner spray.

@chriswing5187 3 жыл бұрын

Mine is also doing the engine check light and goes into limp mode. So I will try this first

@icku 3 жыл бұрын

Before that connect the car to Opcom and read the erros codes just to be sure :)

@Tela-gv8rh 9 ай бұрын

Si,did it Work

@icku 9 ай бұрын

Yep :)

@kalipso7577 2 жыл бұрын

Короче всё в краце разбираешь чиштишь старательной резинкой контакты и вуаля всё хорошо работает!

@yoanfeliz4350 Жыл бұрын

Thanks boy I can solved my problem 🎉

@thekrustykrabrestaurant Ай бұрын

It's variable transistor

@ricsajpeti Жыл бұрын

Hello, at how many km did the error occur? I'm curious because we manufactured this sensor in 2007 :).

@icku Жыл бұрын

Around 160 000km.

@primozhrastar Жыл бұрын

203 000 km

@schwuzi 6 ай бұрын

340000 with my Zafira B

@cornelivan6812 8 ай бұрын

Whatever, i will b esplaining

@fingerprint8479 Жыл бұрын

Hi, nice video, thanks. If I want to buy this sort of circuit board what should I search for? Thanks

@icku Жыл бұрын

No way to source it. At least I didn't manage to find any :(

@julezbarham9907 Жыл бұрын

I'm a week away from calling my astra a reef 🏎️💨....... 🐬🐙

@juanpena9386 13 күн бұрын

That's a new pedal, I see no dust or wear anywhere

@icku 12 күн бұрын

Damn, you got me 🤣🤣🤣😒

@juanpena9386 12 күн бұрын

@@icku don't get me wrong, what you say might work sometimes. I'm about to disassemble mine so wish me luck

@johnnyperry3149 Жыл бұрын

Watch the cost of one of these

@marcusmpiana2967 Жыл бұрын

Honda Pilot 2007

@carldock5223 Жыл бұрын

Cleaning helps but does not solve. Clean and use a pencil 6B or 8B afterwards. The grease pencil will restore the contacts. ONLY these way you can fix FOREVER the problem. Is it possible that no one understands how these potentiometers really work?

@icku Жыл бұрын

It seems your are one of these guys not understanding how they work. Applying graphite will change the resistance of the potentiometer paths. You can never apply same amount of graphite on the pads/paths - those are layed by machine. So if you do it by hand will end up with one path having more of less graphite then the other/more or less resistance. The ECU is monitoting the voltage drop on two paths if I remember correctly and due to different resistance you will get different voltage - resulting in ECU spewing error codes. A really bad idea ;)

@carldock5223 Жыл бұрын

@@icku yeah yeah, do whatever you want, I use graphite

@cornelivan6812 8 ай бұрын

Nice effort fell asleep

@icku 8 ай бұрын

Well not my fault your not taking your medication ;)