Idle Relearn - FX35, I35, M35, G35, G37, 350z, 370z, Maxima, Murano, Sentra, Altima, M45, M56,

Рет қаралды 493,331

7 жыл бұрын

How to Reprogram your Throttle Body. The easiest youtube idle relearn video. I show you how to reset your idle to OEM spec at 650 RPM. ENGINE CODES p0507 p2102 p0603 p2118 P0123 and P0233
MAKE MODEL YEAR CYL LITER
INFINITI G35 2003 - 2006 V6 3.5L
INFINITI I35 2002 - 2004 V6 3.5L
INFINITI M35 2006 - 2008 V6 3.5L
INFINITI TRUCKS FX35 2003 - 2009 V6 3.5L
NISSAN 350Z 2003 - 2005 V6 3.5L
NISSAN ALTIMA 2002 - 2006 V6 3.5L
NISSAN ALTIMA 2002 - 2006 L4 2.5L
NISSAN MAXIMA 2002 - 2008 V6 3.5L
NISSAN SENTRA 2002 - 2005 L4 2.5L
NISSAN SENTRA 2003 - 2005 L4 1.8L
NISSAN TRUCKS MURANO 2003 - 2009 V6 3.5L
NISSAN TRUCKS QUEST 2004 - 2009 V6 3.5L
NISSAN 370Z
INFINITI G37
Preparation
Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied. Learning will be cancelled if any of the following conditions are missed for even a moment.
Battery voltage: More than 12.9V (At idle)
Engine coolant temperature: 70 - 100 C (158 - 212 F)
Park/neutral position (PNP) switch: ON (Shifter in Park or Neutral)
Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed-up (Drive vehicle for 10 minutes.)
Operations Procedures
1. Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.
2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.
2a. Fully depress the accelerator pedal (HARD).
2b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
4. Fully release the accelerator pedal (while the CEL is still blinking)
5. Wait about 10 second.
6. Fully depress the accelerator pedal and keep it for more than 10 seconds.
7. Fully release the accelerator pedal (The CEL light will continue to blink).
8. Turn ignition switch to “OFF” position and now you can start the car. The CEL light should be gone.
If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to resetting the ECU.
Accelerator Pedal Release Position Learning
Operation Procedure
1. Make sure that the accelerator pedal is fully released.
2. Turn ignition switch “ON” and wait at least 2 seconds.
3. Turn ignition switch “OFF” wait at least 10 seconds.
4. Turn ignition switch “ON” and wait at least 2 seconds.
5. Turn ignition switch “OFF” wait at least 10 seconds.
Throttle Valve Closed Position Learning
Operation Procedures
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch to “ON”.
3. Turn ignition switch to “OFF” wait at least 10 seconds.
Make sure that the throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume Learning (Throttle Position Learning)
It is better to count the time accurately with a clock.
1. Perform “Accelerator Pedal Released Position Learning”.
2. Perform “Throttle Valve Closed Position Learning”.
3. Start engine and warm it up to normal operating temperature.
4. Turn ignition switch “OFF” and wait at least 10 seconds.
5. Confirm that the accelerator pedal is fully released, then turn ignition switch “ON” and wait 3 seconds.
6. Repeat the following (steps 7a, 7b) procedures quickly five times within 5 seconds.
7a. Fully depress the accelerator pedal (HARD)
7b. Fully release the accelerator pedal.
8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the Check Engine Light (CEL) stops blinking and turned ON.
9. Fully release the accelerator pedal within 3 seconds after the CEL is ON.
10. Start engine and let it idle.
11. Wait 20 seconds.
12. Rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications.
p2102 p0603 p2118 P0123 and P0233
Nissan Electronic Throttle Body (ETB) Re-Learn Procedure

Пікірлер: 954

@hillbobaggins 5 жыл бұрын

Don't even need a stopwatch. You provide one! Haha. I followed everything you did in real time and it worked flawlessly. Thank you!

@MrStonedstickup 4 жыл бұрын

Will this work on a 2012g37 xs??? It's push to start

@turboek2civic6 4 жыл бұрын

Thanks for the big help lol

@destinyachieved4599 4 жыл бұрын

@@MrStonedstickup it should

@MrStonedstickup 4 жыл бұрын

@@destinyachieved4599 worked flawlessly. I was nervous bc I was reading other people's comments that had issues afterwards. Usually that's me. Or it just doesn't work like the videos do. Always a trip to the parts store or something lol. I'my case this time tho. Perfect. Great video. Got my follow a long time ago. Videos are great !

@kristinasedlacek9530 3 жыл бұрын

Right he's freaking bad to the bone!! Some heroes don't wear capes

@armandomenendez8614 5 жыл бұрын

Yooo I had really underestimated how precise it needed to be, thanks for the detailed explanation. Glad to see helpful channels out there, keep up man!!

@brents5308 5 жыл бұрын

You have no idea how helpful this video was!!! I tried about 3 of the other ones and they didn't work for me. This one worked and the process was easier too.

@letsgetcookin566 6 күн бұрын

Wow man, this really helped a lot. I recently finished fixing up my 2006 g35 coupe and realized that it the idle was being very weird. It jumped from 600 rpm’s to 1000 back down to 600, and made the car annoying at times. I found this video without realizing I had to relearn the idle, since I did remove the throttle body to replace valve covers. This video helped a lot and I just finished the relearn.

@drew0991utube Жыл бұрын

Timing is the most critical step in the relearn process, and your tutorial was on point. I have successfully completed my electronic throttle relearn.

@RicardoRodriguez-pr3wj 6 жыл бұрын

After cleaning the throttle body on my 2005 Nissan Frontier V6 4.0l my idle went out of whack. The relearn worked the first time I tried it. I did it right beside your video and I didn't even have to look at my check engine light blinking. Timing is everything. Thanks!

@depsqu 4 жыл бұрын

You made it so easy to do the re-learn appreciate that. M35 is back to normal🙏🏾

@raidenjr7896 6 жыл бұрын

Boooy u're a star .. I had a high rpm on idle & the check engine light was on. So I followed ur procedure & it worked .. It went back to normal & the check engine light disappeared .. Thank God & thank u .. Definitely thumbs up 👍

@martyvee1641 5 жыл бұрын

Thank you for making this process much more interactive! you made it easy. Thanks for taking time! This would be my 3rd time resetting it and you simplified it. Blessings

@mistros5684 Жыл бұрын

Why did you have to reset 3 times?

@mporterp 4 жыл бұрын

Thank you for the video. I had been fighting to do this from various descriptions, but seeing it made it all much clearer.

@rubencontreras427 5 жыл бұрын

Thank you for your video!!! We have a 2007 Nissan Altima 2.5L. It was having an erratic idle. So we tried your steps and it WORKED!! after doing the steps 4 different times. On the 4th try it WORKED!!! So my son and I thank you!!!!

@nandoa6912 4 жыл бұрын

I had to take the time to thank you for posting this video. I kept following the instructions that you showed on that page and that everybody else has and it wasn't working for me. I did the shortcut procedure you did and my engine is back to spec. Thanks again!

@jonrivera 2 жыл бұрын

Sir you are a brother in arms. I did this to both my Z's - '12 sport tour, '16 nismo. They run noticeably smoother now, and actually identical to a brand new '20 base model one of my buddies just got. That gives me all sorts of peace of mind

@jkthomas1000 2 жыл бұрын

Just bought my 06 Infiniti G35 and had a high idle. After tune-up, oil change, air filter, intake hose and boot. I watched your video and voila!! I'm at spec. Really appreciate the tutorial. Please keep making videos that's very informative. Thanks for everything.

@speedracer2831 2 жыл бұрын

5/4/22 ....and here i'am again, visiting the archives of Motordyne G35 ✊️ just performed the idle relearn, and it went perfect the first time. I just followed you real time on the video. I replaced Bank 2 Sensor 1 (O2) today, and cleaned throttle body, MAF, filter, oil, etc...sooo, did the idle relearn. Once again, THANK YOU for doing all these vids. My 06' Coupe just cleared 50k, and she running like a champ!!!

@howarddavis8748 6 жыл бұрын

Hey motordyne..... First of all I want to thank you for all your dedication you have given into all your various video that have been released! I (we, the viewer's ) have gained a plethora of knowledge from your research! I recently bought a 06 g36 sedan this last summer. I started out installing a 5/16 plenum spacer (yes, reviewed you insight on this) and never thought twice of resetting the idle air circuit...so this whole time ive lived with a higher idle approx. 950-1000 rpm's.and 2k+ cold starts! I excused this problem believing it was the intake that i installed at the same time and was in need of a tune.. when i came across the video i was interested in the idea that i may benefit form this. So tonight after work, i followed the instruction you clearly laid out and....... snap! my idle is right on the money. no more brake lag (harder to stop a vehicle with partial throttle plate opened all the time) and no more exceeding high idle start-up. We appreciate the material you deliever.. keep up the good work!!

@MemosGarageAZ 4 жыл бұрын

Before this vid I was only able to successfully do this maybe once out of 10 times. Now with this vid, I've been able to do it two times in a row, very nice thanks to the poster for making this 👍

@chrisd5758 2 жыл бұрын

4 years later still helping people out! Thank you bro I just bought an 05 g35x had a few issues but all was fixed except the idle, this vid did the trick, thanks again im subbed.

@czurz79 4 жыл бұрын

I tried a couple of other vids on this procedure, and yours is the only one that gave me positive results, wow! Thanks bro!

@PackDaddyOG 20 күн бұрын

Out of all the videos, I watched this was the easiest one to understand and follow.

@herfilms3376 4 жыл бұрын

I wrote down what you did and followed that instead of that paper. You explained it better. Thank you!! :)

@alejandronapoles8554 6 жыл бұрын

Worked perfectly on my 08 infinity g37s with push to start. After deep cleaning both throttle bodies and switching over to cold air nismo intakes the idle was flunctuatuing a lot. Timming is everything flollowes the steps and worked beautifully thanks alot great video.

@zenriddle 5 жыл бұрын

After cleaning my throttlebody and disconnecting harness my idle went upto 825 rpm. I did this idle relearn procedure on my infiniti i35 and it worked. My high idle has gone and back to normal. Thank you very much.

@Basshunter745 Жыл бұрын

I tried this method on my FX35 and it worked like magic. Thank you very very much for making this video!!!!

@happydays2475 5 жыл бұрын

Hey Thank you so much for showing me how to adjust the idle on my 04 g35 I would of never figured it out

@julianpedro4198 6 жыл бұрын

Thanks!!!! The only version that really works, you save me, I bought many car parts to solve it and it was only a simple relearn

@RichardPeraltaC 3 жыл бұрын

Uooo awesome Thank you!!! It worked

@mech4061 3 жыл бұрын

This worked perfectly for my 2007 Nissan Murano V6 3.5 L I watched a few other videos that didn't describe it the way you did the stopwatch worked perfectly because I was able to do it exactly along with your stopwatch while you were doing it. Thanks for the video helped me tremendously

@EmpoweredMovements 4 жыл бұрын

@Motordyne G35 ...Thank you so much for this helpful video! I bought a new throttle body for my Nissan Altima. One repair shop said they would not install it, another shop installed it but did not know they needed to do a relearn procedure (neither did I, at the time). After looking at a few videos and trying the relearn procedure a few dozen times (unsuccessfully) I found your video and did it the way you said to do it and IT WORKS!!! Thank you for sharing!

@rcandrew1996 5 жыл бұрын

This video was perfect! I installed Z1 intake couplers on my 05 G35 sedan, and figured I'd clean the throttle body while I was there. Got the P0507 within about 2 minutes of driving. I queued this video as I did the re-learn. Idle is now around 675-725. no more 1100 rpm idle! Thanks!!!

@chris407x 5 жыл бұрын

Thank you! Great vid and helped me reset the idle in a 2004 Infinity G35

@theSalmaPage 2 жыл бұрын

Thank you so much! My G35 was idling rough/throwing the P0507 code and seeming to be getting worse...enough to where I was putting it in neutral at red lights and stop signs because I felt like it was wanting to stall out. Found this video and 100% fixed the problem. Just followed along with you and done. Saved me a mechanics bill. ❤️

@mrv6uk 4 жыл бұрын

I downloaded this very document from another source after cleaning the throttle body on my 350Z. It now idles just like the day I bough it. Great guide!

@garyantillon5181 4 жыл бұрын

WHOS HERE IN 2020 HELL YEAH BROTHER BACK IN BUZINESS GOT MY G35 RUNNING RIGHT GOD BLESS YOU!!!!!!

@raphael7606 4 жыл бұрын

what were your issues mine kept wanting to die then isles at 500 i did the relearn twice but i was in a rush and it seemed to make it slightly worse but i’m going to try again

@chitos2132 3 жыл бұрын

I did it ab 4 times just now and it worked finally

@PLATINUM2U 6 жыл бұрын

You saved me right at 200 dollars!!!I had replaced my throttle body with a new one. My car has 375k miles.. I was just gonna give up on it. But your video will be the reason I won't give up on my Altima.. Thank You!!😇😇😇

@raft5205 Жыл бұрын

Does your car have 375K miles or kilometres?

@twalpine 10 ай бұрын

Absolute money 💰!!!! I had run through multiple cycles from other videos and they weren't working, this one fixed it first time. You are the man, and probably saved random people from getting screamed at today.

@rishirammoonesar3171 3 жыл бұрын

I tried everything but take it to the dealer and that's something I don't want to do after watching this video it really gave me instant results thank you so much and I know I speak for a lot of people when I say thank you thank you thank you!!!!!!

@alcon6531 6 жыл бұрын

Great video best on KZfaq for the Nissan relearn

@8989Capo 5 жыл бұрын

Worked on my 08 G35. Thanks!

@lgarla23 3 жыл бұрын

Is yours push start? If so how did you do it?

@Alvlol 2 жыл бұрын

How?

@apaquarius 4 жыл бұрын

This worked great! Just installed nwp throttle body and the other relearned were working a day or to. This relearn is awesome!

@Fresh8208 Жыл бұрын

Just replaced a crankshaft and tranny, and couldn’t figure out why the car was rough idling. Remembered your procedure, and she’s fixed! Thank the Lord, she’s fixed!!!

@alexg8460 4 жыл бұрын

I had to go through 5 videos to find yours, thanks so much !! Like👍👍👍

@ald1292 6 жыл бұрын

Your bad ass man... keep uploading vids bro

@enochbos1on 4 жыл бұрын

I sometimes get very rough/jumpy gear changes in automatic (G37X) The car has no get up, limited power etc. Have to use manual mode to get it somewhere to park, where I inevitably find a high idle, and sometimes an engine warning light. This usually only happens in extremely wet or snowy conditions, maybe once every few months or so. This video, the idle relearn completely fixes and solves the issue everytime. Thanks!

@djredrover 6 жыл бұрын

I tried 3 other videos all crap.. THIS is the only one that worked!!! Thanks mate appreciate it!!

@moneygrip4464 5 жыл бұрын

Brother I think the almighty parted the clouds from his throne look down on me and said you know what I mean to send this man and his video your way to help you with this extremely difficult Nissan thanks a whole bunch brother I really appreciate it thank you

@natividadramos4689 4 жыл бұрын

James Burns ridiculous comment

@VisualAnalog 7 жыл бұрын

Ive had a rough idle for almost a year now and i never could fix it. Thank you man!

@MotordyneG35 7 жыл бұрын

Yeah the instructions can be confusing to do all timed up exactly right, the stop watch approach I show makes it much easier. Thanks for letting me know it helped you!

@notafraid551 7 жыл бұрын

I dont have a check engine light in my g35 from 04, help?

@MotordyneG35 7 жыл бұрын

What is the issue? Rough idle? Did you get the check engine light to blink and then to turn solid like in this video?

@notafraid551 7 жыл бұрын

No I mean there is literally no check engine light on the dash of the older g35s, so idk if this idle relearning would work for those years. It only has the service engine soon light in the gauge cluster. When the car idles, sometimes randomly there is like a tiny deep pop and the car shakes a little more when that happens

@MotordyneG35 7 жыл бұрын

This works for all G35's. The check engine light in my car says the same thing, service engine soon, is what it actually says word for word when it lights up. Did you try to do this with no luck?

@Chubbycat747 4 жыл бұрын

Used the vid after I worked on my G35 intake. The light blinked like you said. Car still works, thanks.

@rodrigogarcia8917 3 жыл бұрын

Tried this on my 06 maxima, I was having low idle issues and it totally fixed the issue, thank you! Didn't even need a stopwatch 😂

@goseup 5 жыл бұрын

that stop the jerking on my 05 max dud thanks..!

@ahyungrocks5509 6 жыл бұрын

Let me give the most valuable advice. Just play this video and follow it exactly in your car. Not need to mess with paper instructions or additional timers. I got it to work in my first attempt. Was a bit nervous at first worry that I have the procedures mix up. Now the idle is down to 600-650 rpm. Thank you!

@chupapimunanyo0108 6 жыл бұрын

Just did this Idle relearn and the ECU reset to my G35. IT WORKS! 👍 much needed help.

@ashishpatel1685 6 жыл бұрын

I tried this to 2004 altima 2.5s and it work at a first trial. and car is running great wroom wrooom. great video

@syedhussain3810 4 жыл бұрын

just did my FX45, idling was around 1000RPM lots of gas smell from the exhaust, now everything is normal idling around 700RPM no more gas smell

@_vislow_7307 4 жыл бұрын

My car is idling at 1000rmp I thought that was normal and I smell gas from the car. Hopefully this will fix the problem.

@homxr2493 3 жыл бұрын

@@_vislow_7307 did it fix it?

@_vislow_7307 3 жыл бұрын

homxr no it didn’t I’m not sure what I did but I’m good now after I got tuned around may

@mcncheese1235 5 жыл бұрын

Mine blinks till it stays solid when I turn it back on the service engine light stays on still

@lornesburnphone2474 4 жыл бұрын

It may be a code for something else or the new throttle body you have is broken

@kales003 4 жыл бұрын

It's most likely the old code. Just clear all the codes with the OBD2 scanner and it shouldn't come back

@ManuelHernandez-zl5cx 3 жыл бұрын

Dude it worked! Thanks I have a 2006 fx35 that just had some work done and the idle was high. I Followed your instructions as you we’re doing them and it worked! 👍🏽

@kidryanpz 3 жыл бұрын

BLESS YOUR SOUL! It's been one thing after another with my 2018 Q50 .. and seeing the check engine light had me worried ordered an Ob2 scanner did it and one less stress! Thank you

@Witthevibez 7 ай бұрын

This has to be the most helpful video on a 350z on the internet ! Perfectly said

@user-db8vg1fo7q 5 ай бұрын

Homie has been helping me out for years. This video is perfect. Thanks man

@isaiahshearin 6 жыл бұрын

Watched like 2 min into the video first try . Didn’t even have to use my stopwatch or nothing just followed first what you said the first time and boom my car is idling perfect . Thank you for your videos and your organization and the time you put into this . Need more people like you . Thanks again

@DanielShepherdjr 2 ай бұрын

Thank you so much for this video. I feel very blessed to have a special person like you in the community. 💯 This has helped my car very much. My Infiniti feels great after this! 🚗💨

@Matrex47 6 жыл бұрын

This is the only video I've came across that actually worked. First try too, awesome video bro

@ryanfranco9185 11 ай бұрын

I love you!!!!! I was stressing so much I was idling at 1200 after installing bigger TB and intake after your help now I’m idling at 650

@funningoffroad 3 жыл бұрын

Thank you for giving the steps in the description! Very helpful video

@Cab895 3 жыл бұрын

No need for a stopwatch because of your awesome video, Thank you!!!

@speedracer2831 2 жыл бұрын

Right!!! I just did it, and followed in real time. Worked perfectly on the first run!

@Nolan_Harley 4 жыл бұрын

Thanks dude pretty clutch quick fix on my 06' g35, pretty sure you've helped me before too. Cheers from Canada brother.

@Ootgreet1 Жыл бұрын

Thank you for this video. I resolved the P0507 code on a 02 Maxima. I'd tried using the procedure in other videos that have you doing the entire throttle position relearn sequence, and not breaking off the actual airflow recalibration as its own sequence. I never got the flashing engine light with other videos because the sequence was so lengthy that I screwed something up. Like others here, I watched your video along while I did the same actions in real time. So easy! And the idle speed dropped noticibly from crazy fast (lurching when I put into drive) to normal subdued, showing around 700 RPM on the tach.

@BlxckSoL Жыл бұрын

🙏🏾 thanks! I cleaned the throttle body the other week and didn’t know this was even a thing!

@NaidaLon 2 жыл бұрын

I followed every steps in the procedure. I got lucky the 2nd time of tries Thanks for the very good content. It helps a lot to avoid costs. Haha.

@kevinphan9907 11 ай бұрын

This video deserves a million views, thank you.

@sugarraysmith5450 5 жыл бұрын

Thanks! Been using the other guys methods and no luck. Used the 15 second method and problem solved. First Time!

@nantiabezani8466 4 жыл бұрын

Hi, thanks a lot !!! It worked for me, I have an Almera 1,5 N16. I cleaned my throttle body and then the idle speed was 950 rpm. I tried other ways to make an idle speed learning but nothing really worked, until I found yours. Thanks again my friend.

@alexandercastillo87 6 жыл бұрын

Thank you , life saver , gas saver lol . Your video worked great . I will save it for when I swap out the throttle. Thanks a million . My o6 SeR is back to normal .

@franciscoreyes771 7 ай бұрын

I just got a check engine after cleaning the throttle body and this fixed my idle! Thank you so much!

@MrJpagan2 6 жыл бұрын

Ha ir worked to think I almost bought a new throttle body I tried all of them and nothing your way worked thanks man cheers from providence Rhode island 👍

@dsmred6575 2 жыл бұрын

Man ive tried sooooo many videos they didnt work. Yours worked flawlessly!!!!! Thank you soooo much you definitely gained a subscriber!!!! Cheers

@richmedina2324 6 жыл бұрын

Finally did it after so many attempts wow. Thank you very much very helpful..

@hp9457 Жыл бұрын

Thanks for your video. Helped me after I cleaned the throttle body. Saved me time and money having to go to the auto shop.

@jkrebuiltenespanol9264 3 жыл бұрын

Thank you so much! I did it along with you and it worked! It hadn’t worked before!

@Shinigami_Kishi 4 жыл бұрын

Just got my 03 G35 in a trade and had a high car idle your video helped thanks

@whitesharkdiver Жыл бұрын

Seriously, honest thank you. Did this on 2005 FX35 and there was a little variance in how the engine light blinked, but it worked great.

@tomparanzino 5 жыл бұрын

Worked beautifully. 2004 G35x sedan. Thanks!!

@MrSmookebreak 3 жыл бұрын

Work when I did my g35 2 yrs ago. Now I’m in a G37x and did it and it worked. Thanks

@gunyvw 5 жыл бұрын

this worked fx45.. was easy... i watched it from my phone... followed the steps n real time...

@FOREVERaPILOT 3 жыл бұрын

Hell yeah my idle has been running about 950 just did it and it went to 650 . Was running a little rough. A lot smoother! Thanks!

@jacobmarshall48 Жыл бұрын

your video is the only one that worked I had to watch like four of them before I finally found the one that work thank you

@sammyavtayev608 2 жыл бұрын

Worked perfectly. No more engine light 👍👍

@gfordeable 4 жыл бұрын

Thanks man out of all the videos on KZfaq on this topic this is the simplest and only one that work for. It is amazing WOW👍😁

@ThatzMikey_G 2 жыл бұрын

Appreciate this video! Fixed my issue within 5 minutes 🙌🏾

@kimbell111 5 жыл бұрын

Man you are a life save the shop told me I need a new throttle body man you save me this the only one that on point thank you

@ventureskater336 4 жыл бұрын

thanks so much for this i had a high idle after replacing tb and watched so many videos then saw yours and got it first try!

@gemmariser4714 2 жыл бұрын

What make and model do you have ? I have an Infiniti fx35 and had the throttle body replaced and I feel like it doesn’t idle correctly. If I’m at a complete stop and let my foot off the break i roll up to like 30 mph without even touching the gas pedal!

@Jamesisamazig123 2 жыл бұрын

bro i been trying this for a week on my 3.5l v6 altima, thank you. it was driving me crazy

@MrSamshows 5 жыл бұрын

Perfect, Thanks worked well, now my car performing well

@joellemartin7283 5 жыл бұрын

Thank you thank you thank you. This was so much easier than the others.

@tibbymat 4 жыл бұрын

Awesome video man. I just followed along with you live which made it really easy.

@bernard-francoistaylor4205 6 жыл бұрын

THANK YOU, THANK YOU, THANK YOU. IT WORKED! The dealer wanted 200 bucks to do it. Your brilliant

@majdiababneh1125 4 жыл бұрын

I have a 2007 infiniti g35 3.5 its a push start i need to relearn the tb was changed can u help me please

@jameskikuoka4863 4 жыл бұрын

This works! I changed my stock throttle bodies in my 2016 45th Aniversary GTR to Curt Brown’s 36 mm polished and bored-out throttle bodies, which required the throttle body relearn. No P0507 code and the idle speed is back within spec.

@pollysek 2 жыл бұрын

Thanks so much for the easy to follow process. This helped me immensely

@hardkore360 6 жыл бұрын

Thanks for this video, for those that cant get it to work the timing is VERY important. By using a stopwatch I was able to get it right in the first two tries

@CamboK1ng 5 жыл бұрын

Thanks u!!! U just saved me from spending money on Throttle body!!! My car rmp jump up and down from 1500-2500... Now after watching your video and did after u my car turn to normal.

@howesthename 5 жыл бұрын

Cass Shu this is happening to me right now, mechanic says needs either throttle bodies or a new ecu. Going to try when I get home from work and try to save myself 800-1000$