Ignition System Troubleshooting: Honda CB175 / CB350 / CB360 / CB450 / CB550 / CB750

Рет қаралды 82,848

4 жыл бұрын

www.common-motor.com/honda-35...
The first thing to check out when diagnosing a poor running vintage Honda motorcycle engine is the ignition system. A points style ignition system only contains a few parts, thus diagnosing issues is fast and parts replacement easy. All the parts must be working properly in the system for proper engine performance, so it only takes one part to fail to cause problems in the system and engine issues.
These troubleshooting techniques will work for the following families Honda motorcycle models (as well as other motorcycles with points style ignition systems):
-CB175 / CL175 / SL175 /CB200T
-CB350 / CL350 Scrambler /SL350
-CB360 / CL360 Scrambler / CJ360
-CB450 /CL450 Scrambler / CB500T
-CB500K / CB550
-CB750K
____________________________
Parts Used:
Spark Plugs
--CB350 / CB360 / CB450 / CB500T : www.common-motor.com/honda-sp...
--CB500K / CB550 / CB750 : www.common-motor.com/honda-CB...
Ignition Coils
--CB350 / CB360 / CB450 / CB500T : www.common-motor.com/honda-ig...
--CB500K / CB550 / CB750 : www.common-motor.com/honda-cb...
Contact Points
--CB350 / CB360 / CB450 / CB500T : www.common-motor.com/honda-cb...
--CB500K / CB550 / CB750 : www.common-motor.com/honda-cb...
Condenser
--CB350 / CB360 / CB450 / CB500T: www.common-motor.com/honda-ig...
--CB500K / CB550 / CB750 : www.common-motor.com/honda-ig...
Spark Plug Boots:
--CB350 / CB360 / CB450 / CB500T : www.common-motor.com/honda-cb...
--CB500K / CB550 / CB750 : www.common-motor.com/honda-cb...

Пікірлер: 98

@davidrosen5137 4 жыл бұрын

Incredibly helpful video Brenden and Team CMC (on the "internets")! Used it to trouble shoot my 71 SL350 today. Helped me quickly isolate and fix the issue. Cranked on the third kick after sitting for over 40 years. Please keep these videos coming; they are more helpful than you know!

@chrisscott7522 Жыл бұрын

Phenomenal amount of quality info - perhaps a bit quick for dunces like me, but I can always watch it again, and again ….! Thanks

@gregmcfarland8639 4 жыл бұрын

Thanks once again for taking the time to share this with us, good one guys!

@Johnny2Bags47 Жыл бұрын

I have 2 left hands and I honestly have zero idea what I'm doing with my 1981 Honda CB750 F and I think this made sense. I'm gonna give it a few tries in the morning and running through this video a couple more times. Thanks

@petemoe4495 4 жыл бұрын

Thanks Brendan--another super helpful video!

@kamakawiowoole Жыл бұрын

Thanks a ton! This was a perfect breakdown to help straighten out the chaos of troubleshooting! very well done! Can't wait to get cylinder 3 and 4 fixed on my 76' CB750 project

@davidmiller5657 4 жыл бұрын

Excellent! I’m working on a 1973 CL 350 that was in storage for 30 years. Lots of gremlins from sitting so long, but thanks to your video, some sandpaper on the points quickly resolved the no spark problems.

@CypressVintage 3 жыл бұрын

Very helpful. Quick, concise and to the point. Thank you.

@geoffreyjones2000 4 жыл бұрын

Very thorough in under 7 minutes

@seanofoghlu5747 3 жыл бұрын

Thank you sir for this simple and easy to follow explanation, I am in the process of my first restoration project and found this most helpful information .

@johnnyturbo8460 3 жыл бұрын

Excellent video. I have some things to check tomorrow

@bonnjohnston9290 4 жыл бұрын

excellent video. I've been having issues with my bike running poorly for awhile now, even after swapping in new points and a condenser.

@MiriaCambie 4 жыл бұрын

I'm so happy!!! you've given me the confidence to do this ignition service myself. Thanks for saving me a lot of money really Brenden.

@abdullahryan8816 3 жыл бұрын

pro tip : you can watch series on flixzone. I've been using them for watching all kinds of movies during the lockdown.

@keeganplunk6867 3 жыл бұрын

So glad i found your videos!🤘

@shedbuiltmoto 4 жыл бұрын

Nice Looking Scrambler There ! As Always Great Video Very Helpful.

@jbdonnelly19 Жыл бұрын

Thank you! So systematic and clear. You rock

@lazer51 3 жыл бұрын

Never seen a video on this method before. thanks.

@maxdelnegro7168 Жыл бұрын

Nice tutorial, thanks. 💯

@billbraxton7192 Жыл бұрын

finally. a useful video on ignition issues. sub'd

@plusblood5101 Жыл бұрын

Very good video Gr8 tips

@gordontainsch2624 Жыл бұрын

That cleared up some things for me. My 360T may have a poor condenser as it is 'arching' for that right cylinder. I will replace the condenser. Stator and coils are new updated versions. Thanks.

@victor_iosi 2 ай бұрын

Very nice and informative video. 🙏

@alphamale7424 2 жыл бұрын

Damn Fine Video My Friend!

@thomaslockley945 3 жыл бұрын

great video very infprmative an easy tp understand

@joshbauer650 8 күн бұрын

Thanks so much for this saved me time and money.

@mikeshobbycorner 4 жыл бұрын

Awesome vid! Thx. Will try this to get my CB250 going!

@Common-motor 4 жыл бұрын

glad to help!

@kentuckyyankee 4 жыл бұрын

Very good! I just made a video a few days ago, about having a bad ground to the coil bracket, so many variables with old bikes

@Common-motor 4 жыл бұрын

Bad grounds are something that many overlook

@RCASSIN 4 жыл бұрын

Excellent. You have explained the trouble shooting better than anyone! Do you have a video on adjusting the points?

@ChrisMillerdoubleplanet 4 жыл бұрын

I really appreciate you guys! Great video. Great service. Thanks man!

@user-qo5hh9bw4w 2 күн бұрын

I gave up on my 72 cb350 because I couldn't get quality coils. Repair genius tried to convince me that single lead new coils would work but they would immediately blow out.

@jeffmullinix7916 Жыл бұрын

Hi Brenden .! I been working on a real bad problem for the last 2 weeks solid . It is a 1975 CB360 , I just cant figure something out . I have replaced coils twice . The guy I bought the bike from had bought a lot of things from you including new coils . Those coils made some improvement for a little while from the Honda coils he said . Then he told me that the bike just would not start or vary hard to start and and if started runs vary ruff . Like a fool I bought the bike because it was really clean and I owned one back in 1979 . Great bike but not my first bike . Back to this bike . Well I check voltage at batt and it charge and hold charge at 13.35 volts . The engine run and off switch failed . Some jack weed messed with or I should say jerry rig it and failed . I replaced that . Hoping that would repair the voltage problem . It did not . So the problem I believe that I am only getting 11.43 volts on the black wire with the white stripe at the coils . Seems strange to me . Because I am getting or think I am getting well above 13 volt out of the stator at idle . Can you advise me where to turn or where to check in order ? Thanks Jeff

@donbrashsux 3 жыл бұрын

Great vid info ..thanks

@alexanderduvill6878 3 жыл бұрын

Thanks for the vid!

@plusblood5101 3 ай бұрын

Awesome info

@chaswood1234 4 жыл бұрын

Great Video

@davidsprague4592 3 жыл бұрын

Thanks for the awesome video. My right cylinder has no spark, I took off the points cover the right point was sparking like in the video. I swapped the wires and had no change. What should I look at next?

@mooser321 Жыл бұрын

Thank you, thank you, thank you!!!

@BobbyDeathboard 3 жыл бұрын

Great video, breaking it down nicely. My 71 CB500 was having trouble running consistently. Ended up caving in amd bringing it to a local shop. They told me my coils were wired up wrong....how would it run at all if that was the case?

@tommyhornsby1897 2 жыл бұрын

I love that bike.

@KevinSmith-gh5ze 4 жыл бұрын

Thanks for another great video. Your videos and parts store have been very helpful on the 71 cl350 I am restoring. Could you do a video some time on how to check if your stator is good? I'm having issues with my battery dying after a while of riding. I know my stator is putting out power, and it is running both coils constantly, but I don't know how to tell if it's putting out as much power as it should be.

@brentcassidy357 2 жыл бұрын

Just discovered your channel, great info! What about when you start bike and only one cylinder is running so I pulled plug wire on cylinder not running and barely let the plug wire hang on the spark plug and then the cylinder runs.

@thomaslockley945 3 жыл бұрын

What if mine is hard to start but when it does fires on both cylinders till it warms up about 15 min then one cylinder spits an sputters

@jims41 4 жыл бұрын

As with almost all of cmc’s videos this is a great video. however i would have reversed steps 1 and 2.

@jakem20 3 жыл бұрын

Great Video. Learning a ton of info from you guys. So.. I swapped my condenser with new ones from you, I still couldn't get my bike to rev at 5K. Any Idea what to look for?

@donaldcameron8909 3 жыл бұрын

Cool bike

@jasonbishop7356 2 жыл бұрын

Having issue with s charging system got your rectifier/regulator combo so trying to determine if charging system working on my 71 cl450k4

@kingsman4L 3 жыл бұрын

Which continuity test light should I buy???

@Ivanskrakow 2 жыл бұрын

What if you don’t get power ? no lights etc, when turning on the key?

@nicholashall4639 4 жыл бұрын

thanks for doing this! Question.... is this video showing a step by step process? I can pull the spark plug out, like you do at 5:27 , and it still runs, so is that straight coil issue and I dont have to check the other parts? Or should I start from the beginning. 1973 Cl350. Thanks!

@wackawolff 3 жыл бұрын

my test light turns on with the alligator clip on the positive and the probe on the negative, but not the way you showed. why is that? i’m also deducing down to a bad spark plug coil but wanted to figure out that first and most basic test. smh

@itfc3 Жыл бұрын

hi in the last test if you remove the cap and the bike dies what does that mean

@gregwolters2 3 жыл бұрын

So I’m assuming when u ck the coil pick up wires the electronic ignition has to be on dead top center for the light to glow on 1and 2 (yellow) wire and dead top center for 3and4 (blue and yellow wire). Correct?

@meganreichenbacher1441 3 жыл бұрын

I just replaced the points on my 1975 mt250 and have been trying to use a method with a micrometer to set the timing. Even when I can see that the points are visibly open, I am still getting the same ohm reading as when they were closed. In a video I saw using this method on a 76 MR250 they showed the ohms dropping slightly as the points begin to open. My bike has spark but is nearly impossible to start and runs super rough when I can get it going. Any advice?

@jackyyeung7903 3 жыл бұрын

do you guys have the ignition switch holder for a CB500k2?

@rene-yvescote3954 4 жыл бұрын

One thing that I do is, when checking the battery I use a multi-meter the confirm that I have 12v and connect the negative lead to the frame this way I make sure that I have a good ground connection. I also rev the bike to see if my charging system/generator is working. Voltage go up around 14vdc.

@Common-motor 4 жыл бұрын

Great recommendation. However just a note on the the CB175 / CB350 / CB360 / CB450 typical charging voltage is between 12.5 to 13.2 volts.

@Common-motor 4 жыл бұрын

Yes a healthy battery is key to a good running vintage Honda. The typical charging voltage you will see on the twins is about 12.5 to 13.2 volts.

@davidrosen5137 3 жыл бұрын

Suddenly no spark. Running through this video again. Silly question; where does the engine pick up its ground? I check my coil wires to the negative post of the battery, I get 12.4 VDC... I check them to the engine, I get 0VDC!

@dannyallen1082 2 жыл бұрын

I have a 1982 CM450A. The bike will kickstart and run and drive great, with the key turned to on and switched to run. But none of the lights or push button ignition works. Basically none of the electronic elements of the bike works but it runs and drives when you kickstart it. Any idea what the could be? All of the fuses and battery are good.

@darkcustomxxx7252 3 жыл бұрын

does a faulty condenser cause the coil to get hot, which leads to a lack of or jumpy power once the coil is hot? I have a c77 that's doing this. I replaced the coil and now the new coil is getting hot like the old one. It cant go more than a few miles without the coil getting hot and then hesitant power.

@danielpearson4525 5 ай бұрын

I have a 72 cl 175 and I don't have any spark on the timing points does anyone know what is up with it?

@snakedoc6812 Жыл бұрын

If there was a double like button, I'll press it 👍👍

@czapskibusinessgroup Жыл бұрын

I get power to my ignition switch but when I turn it on its not working. If I move some of yhr wired around it it flickers dimly but does not power on. Any ideas?

@mickeynicholson4054 Жыл бұрын

Cleaned points but Light is staying on after manually opening points. Any idea on what’s going on? Any tips?

@austinmonahan7022 2 жыл бұрын

I have a 1974 Honda Cb 200 & the electric starter won’t turn over. I hear it clicking though. Any suggestions?

@eFFunt 4 жыл бұрын

I bought a set of coils from you guys. I think one is bad because my dynamic timing light won't strobe on that coil when the RPMs get above 2k or so. It's fine on the right coil....No condenser as I'm on electronic ign. It did the same thing on point though. Bad coil?

@Common-motor 4 жыл бұрын

reach out to our support line on the website, they can troubleshoot you a little more than I can on youtube and see whats going on for you and how we can help.

@johnrolon3577 3 жыл бұрын

On my 1975 Honda CB 200t, I have replaced the battery then installed your regulator/rectifier combo. I have no lights or horn what so ever. The electric starter is functional however. Doesn't seem to be getting spark either. Where should I start my diagnostics?

@Common-motor 3 жыл бұрын

We are currently working on an updated add-on video for the 175/200 family of bikes when replacing the reg/rec. The stock rectifier actually doubled as the harness ground so when you upgrade to the modern reg/rec you need to re-ground the harness somewhere on the bike. This is as simple as making a short length of green wire that has a bullet on one side and a ring terminal on the other. Bolt the ring terminal anywhere on the frame and connect the green bullet into a green connection on the wiring harness. I'm guessing this will solve a lot of your issues if not all of them. A good place to do this is the green connection where the old regulator used to plug into. The wire can easily reach one of the battery box bolts to ground it.

@AsherCB350 9 ай бұрын

Wait is the muffler

@lmc_motorsports 4 жыл бұрын

I have a 1979 CL175 and parts are hard to come by where do you recommend i get my parts from? Id like to replace all the electrical system components.

@Common-motor 4 жыл бұрын

We are working on parts for the 175's currently. Depending on what you need we may already have the parts in stock. Btw check the year on your bike again as '79 was not a production year for the 175's.

@JohnnyTaytor 4 жыл бұрын

i'm hoping someone can help me out, when i check for power at the points, i've got nothing on the left side. testing the dual yellow wire socket, i get nothing unless i unplug the left side point wire, then i get 12-13V. Keep in mind this is a brand new coil, i'm pointing to the condenser now but not sure. any help would be greatly appreciated

@Common-motor 4 жыл бұрын

The contact point must be open for a reading to be present. Rotate the engine till it is open and test. If it is an issue still the wire connecting to the points may be incorrectly installed.

@crisdraaisma5680 3 жыл бұрын

Hi, any idea why and how my timing light on the pickup coil can burn constantly? eventhough the ponts gap has enough space.

@Common-motor 3 жыл бұрын

Email our support with what you've done to troubleshoot and we can help you out a bit more there!

@lazer51 3 жыл бұрын

Will that load test work on a four cylinder as well ?

@Common-motor 3 жыл бұрын

Yes!

@tylerhander23 4 жыл бұрын

Hey man! I have 1972 cb750 and I’m have brake return issue. The brake pads are so tight to the rotor the wheel will not move. Do you know what it could be? I already replaced all the brake hoses ,pads and master cylinder.

@Common-motor 4 жыл бұрын

I'd clean and lubricate the caliper swing are. See our brake rebuild videos for more information.

@Ohvurr_leveraged 3 жыл бұрын

Can coils be fine at idle and fail at higher rpms?

@Common-motor 3 жыл бұрын

What rpm range are you failing at?

@acolonnh1 3 ай бұрын

What a bad condenser cause a no spark issue????

@kelsiebn 3 жыл бұрын

So what do you do if your battery works but the power is not reaching the points and headlight, horn and everything else doesnt turn on?

@rontoops2781 3 жыл бұрын

Sounds like fuse

@richardmuniz3441 3 жыл бұрын

Hello, did you resolve this issue? I am currently experiencing the same thing. I cleaned ground at the coil and two grounds in the headlight, but still nothing.

@pacmanpaquette 4 жыл бұрын

You should really be covering Spark gap, Dwell and timing chain stretch which can also cause ignition problems. Speaking from experience here.

@MiriaCambie 4 жыл бұрын

Please make a you tube video to help out. #visuallearners

@Common-motor 4 жыл бұрын

We, cover all that in other videos on our channel.

@theryanjester7209 4 жыл бұрын

Good stuff. Didn't help me with my issue though :/

@chrissmith7400 4 жыл бұрын

I would have thought you'd get a shock at 5:45.

@andrewhammer4375 3 жыл бұрын

F* it. i should just buy one of every part you sell at this point. I bought a cb360t not really knowing what to look for. i've already spent more on parts than i took out for the loan to buy the bike! never should have bought this particular one, but at least i'm learning a lot??? i suppose that makes it a worthwhile endeavor. Still waiting on a lot more parts from common motors. i wish there was an option to expedite shipping, but i looks like it'll be another 4 day wait for parts.

@andrewhammer4375 3 жыл бұрын

basically, i've owned this bike a few weeks now and have been fixing lots of stuff here and there in that time. just discovered today that this whole time it's only been running on One cylinder. ugh. seems the ignition coil is the culprit. just bought 2 of them (since they look original and the other one probably won't last long anyway), and the condenser, and boots, and new plugs, cause what the F?! why not just replace it all at this point? this bike is gonna be the death of me! or at least my credit score lol.

@andrewhammer4375 3 жыл бұрын

i'm officially Beyond the DIY / fix-it-at-home repairs now. i'm just buying one of everything mentioned in this video, replacing them all, crossing my fingers and hoping for the best