Inner & outer CV joint replacement and restoration. GTV restoration part 8

Рет қаралды 10,528

Rick’s Garage

4 жыл бұрын

dTree:
/ david-staunch
/ dtreemusic
kzfaq.info/love/I-S
Music from Soundcloud
Music provided by FRM: / fkrjrkhdq0zo

Пікірлер: 19

@Zion-jw3gm 2 жыл бұрын

Good God! I'm pretty sure you have THE BEST Alfa repair channel on the interwebs.

@d12drw 4 жыл бұрын

Good work again Rick!! Love the POR15 stuff. And the Bilt Hamber Surfex HD (I use it as a wheel cleaner diluted 10:1). Well done mate 😀👍

@_RicksGarage 4 жыл бұрын

d12drw thank you Sir. Glad you liked it 👍🏼

@floydkingi4364 2 жыл бұрын

Great video mate, helpful to my issue with inner CV joint. Well explained and demonstrated

@paulrowe8131 4 жыл бұрын

Great video. Really informative. Half shafts looked awesome when complete. Watching further progress on the car with interest.👍

@silvertaxi 3 жыл бұрын

Again a fantastic helpful vid

@RJ-mr7rj 4 жыл бұрын

Top work

@carbon_gtv 4 жыл бұрын

Thx for this!

@_RicksGarage 4 жыл бұрын

Dani R no problem. Hope it helps 👍🏼

@MalcoTube 4 жыл бұрын

try westfield fasteners for Nyloc nuts :)

@darrellharris5579 3 жыл бұрын

What makes the CV axle lock up

@farinaGTA 3 жыл бұрын

Superb Rick Could you advise what tool you used to tightened the CV boot clamp? Thanks for the upload

@_RicksGarage 3 жыл бұрын

Hi, the best thing you can use is a pair of pincers 👍🏼

@sergeanthorvath 4 жыл бұрын

Great series of videos. I have recently acquired a 3.0 L GTV with 200,000 kms on it so it will be getting the same treatment as yours in the near future. Just wondering how many miles or kms yours has done.

@_RicksGarage 4 жыл бұрын

Joe Horvath Hi and thanks for the comments. My GTV has done 70,000miles so around 112,000kms

@J2105HD 2 жыл бұрын

If you change the driveshaft on a 3.2 GT driver side does it need new oil ? Or does it drain out oil

@_RicksGarage 2 жыл бұрын

Depends what job you are doing. If you want to remove the entire driveshaft then yes, a quantity of oil will come out. If you only want to replace the joints or gaiters then you can just unbolt the drive shaft at the flange and leave the inner shaft inside the gearbox. Check out this link and skip to 8 minutes 20 seconds In the following video: kzfaq.info/get/bejne/m8dgepRo3ta9imw.html If you want to remove the entire driveshaft then check out this video here: skip to 11 minutes 45 seconds kzfaq.info/get/bejne/gaipf6qIv5uVXWw.html

@J2105HD 2 жыл бұрын

@@_RicksGarage thanks your videos helped me a a lot 👍🏻

@chokini2 3 жыл бұрын

well done! but it is worth to have a look at the balls as well. if they show signs of wear and the shell is still okay, you can replace them for a small amount of money.