Install a Byrd Shelix Cutterherd on 8 inch jointer

Рет қаралды 11,847

2 жыл бұрын

Пікірлер: 40

@bradleytuckwell4881 2 жыл бұрын

They make such a difference and they are a little quieter on the ears thanks for sharing hopefully you might make another build for us. I so enjoyed watching your channel

@charleswilson8915 Жыл бұрын

I have watched every video on your channel, and loved every video. Your patience and attention to detail is amazing. I did not comment on all the videos, but they all got a big like. Hope to see more in the future.

@69kaveman 2 жыл бұрын

Nice work! You are amazing in all you do! Thanks for the video.

@timhyatt9185 2 жыл бұрын

I put one of these on my delta lunchbox planer -- it was like a whole new machine! Sure, it cost 2/3 the price of the planer itself, but the difference was WELL worth that price. Before installing, it was difficult to get a good smooth surface with little ripple. and it was constantly blowing the breaker, even when on it's own circuit. Took me a couple careful hours to install it (was taking my time; more than a little nerve wracking!!! ) but once installed, it was a whole new machine. I could take a MUCH heavier pass and it barely even slowed. and the final finish was just stellar.. if you haven't gotten one of these yet for your machine, GET ONE.. you will not regret it!!

@jcsrst 2 жыл бұрын

You're going to love that new cutter head 👍

@andredionne7769 2 жыл бұрын

j aime beaucoup vos vidéo tres instructif

@jorgeconcheyro 2 жыл бұрын

Congrats on the new head Je!!! Nothing feels better than new ball bearings huh ;)

@275jesuss Жыл бұрын

Knives and cases, the process and finish are certainly different. When I watched it while thinking about its meaning, I felt like I was sharing time with the creator. Have a nice day. /new🔔""

@krenwregget7667 2 жыл бұрын

great choice. I installed a Byrd Shelix head on my Dewalt 735 planer and it made a big difference in noise and finish quality as well as blade longevity.

@YoungJe 2 жыл бұрын

thanks

@alanwasserman8176 2 жыл бұрын

Mr. Je Really nice install on the Shelix cutter, and no parts left over lol

@ianvicedomini2648 2 жыл бұрын

Great job and a very interesting video. It's opened my eyes to what is possible when it comes to machines like this. I hope it pays off effectively my friend 😉👍🏻👍🏻

@ohasis8331 2 жыл бұрын

Looks like you're going to have a lot of fun.

@YoungJe 2 жыл бұрын

thank you~

@MCsCreations Жыл бұрын

Hey, my friend! I hope everything is good with you and yours there! Just passing to say hi and to tell you I'm missing the videos. 😊 Stay safe there with your family! 🖖😊

@aleks9147 2 жыл бұрын

Congratulation, nice equipment!

@chebalad7729 Жыл бұрын

Inspiratif kang mas 👍🏾👍🏾

@jorgeconcheyro Жыл бұрын

long time no see, my regards to you Sir!!!!

@uncannyvalleywoods7248 2 жыл бұрын

Very rad!

@jimurrata6785 2 жыл бұрын

I have a similar 8" Grizzly jointer and was very interested to see your take on the Shelix cutter head.

@dougshaw9701 2 жыл бұрын

if you replace it will be a great time to tune up your jointer reset plane(both in feed and out feed re square your fence took me a few hours but well worth the time .

@jimurrata6785 2 жыл бұрын

@@dougshaw9701 it certainly looks like you'd need to reset the outfeed (but only once as opposed to resetting the knives every time they need sharpening) The 90° fence stop is a janky pivoting piece of iron bar. I need to check with a small machinists square every time I loosen it, unfortunately... This tool has been great value for the $. I rarely wish I had gotten a bigger one. Yes, it is always worthwhile to do proper maintenance and tuning in the shop. 👍

@dougshaw9701 2 жыл бұрын

@@jimurrata6785 I bought a machinist straightedge to reset both my infeed and outfeed to where they were as close to parallel as i could very minor adjustments and yes the outfeed is important that it is parallel to cutter head but if you really want to check get the straight edge.(about 90 bucks for one)found i needed to shim one side of my outfeed to get to even with my infeed(same plane) Since i had to disassemble my jointer it was worth the effort.

@metamech7383 2 жыл бұрын

I waited 10 years to flip the squares ONCE. Those things last F O R E V E R!

@MCsCreations 2 жыл бұрын

Pretty interesting process, my friend! Fantastic work! 😃 Stay safe there with your family! 🖖😊

@YoungJe 2 жыл бұрын

Thanks, I hope you are safe too.

@Marcenariahobbyearte Жыл бұрын

Show de bola meu amigo parabéns pelo seu trabalho ganhou mais um inscrito e deixo aquele like valeu👍🏻👍🏻💯💯🤝

@taejinlee5556 2 жыл бұрын

부럽습니다^^ 조만간 자동대패도 헤드 바꾸셔야겠어요ㅎㅎ~

@YoungJe 2 жыл бұрын

어쩌면요~ 감사합니다~

@SEOYOONJAE Жыл бұрын

선생님 늘 잘보고있습니다 건승하시길 바랍니다

@sergedurand9905 2 жыл бұрын

I am very happy that you can use these pads. BUT... I'm sure they will be less efficient than your own planes that make me dream for so many years 😉 greetings from France

@YoungJe 2 жыл бұрын

The precision is much more accurate with a hand tool, but when you do a lot of work, you need the help of a machine. Thanks~

@ksross08 2 жыл бұрын

I added a Shelix to the same model a year ago. Only issue I seem to have now is getting the beds to be fully co-planner. Did you have to shim the head at all (or the beds)?

@xoxo2008oxox 2 жыл бұрын

Will you give us feedback on why you did this and the comparison how better the finish is now versus past blades? I'm thinking of doing the same to a planer.

@YoungJe 2 жыл бұрын

The noise during machine operation is very low, the machining surface is very good, I am very satisfied