Install a Rotary

Рет қаралды 924

Күн бұрын

More at uglydogwoodshop.com
If you want to install a 4th-axis rotary on your @OnefinityCNC Elite, here's how to do it.
If you feel the need to support my efforts in some way, I offer two options:
Patreon: / uglydogwoodshop -- includes a bunch of free digital models for the Digital Downloads tier.
CashApp: cash.app/$UglyDogWoodshop -- if you just want to make a one time contribution of any amount you pick.
Here's the parts I used:
80mm 4 Jaw Chuck: amzn.to/3JjcrmI
80mm Rotary w/ 3 Jaw Chuck: amzn.to/4aTMO7w
100mm Rotary w/ 4 Jaw Chuck: amzn.to/3VXn8mw *you’ll need to find the right belt on your own if you use this one
2040 Corners: amzn.to/3Q1VBMT
2040 Extrusions: amzn.to/3PXipNW
M5 Threaded Inserts: amzn.to/4aQcJgw
M5 Lock Washers: amzn.to/3UfM3jL
M5 Large Washers: amzn.to/3UeOcMO *needed to span the slot in the rotary, which are larger than M5
M5x22mm Cap Screws: amzn.to/43Wearo
Heat Shrink: amzn.to/4aQArt4
Soldering Station: amzn.to/4aQAxkq
Helping Hands: amzn.to/3JoCfxz
Ferrule Kit: amzn.to/4aVARi2
Molex Pin Crimper: amzn.to/4ay3mCx *you may need to thin it a bit to keep it from mangling the pins. I used a belt sander.
Nylon Sleeve: amzn.to/440pL8Z
10k Ohm Resistor: amzn.to/3xEEiLG
2.2k Ohm Resistor: amzn.to/3vR3SfG
18/2 Wire: amzn.to/43UeYgJ
2-Pin Molex Connector: www.digikey.com/en/products/d...
2-Pin Molex Back Shell: www.digikey.com/en/products/d... *you need two
Female Molex Pins: www.digikey.com/en/products/d... *you need ten but buy extra.
The 3-Pair Wire: www.digikey.com/en/products/d...
8-Pin Molex Receptacle: www.digikey.com/en/products/d...
8-Pin Molex Plug: www.digikey.com/en/products/d...
Molex Pins: www.digikey.com/en/products/d... *you need eight but by extra.
8-Pin Molex Backshells: www.digikey.com/en/products/d... *you need 4
Here's the model for the rotary guide on Thingiverse: www.thingiverse.com/thing:657...
It's also free for the Interactor tier on Patreon:
/ uglydogwoodshop
0:00 Intro
0:13 Motor
1:15 Chuck
2:14 100mm Chuck
3:35 Dip Switches
4:49 Motor Wiring
7:12 Quick Disconnect
8:16 Masso Wiring
10:32 Power Wiring
11:23 Masso Setup
16:26 Mounting
18:33 Zeroing
*Some of the links above are affiliate links. I get paid a very small amount based on purchases from those links. I appreciate it if you use them, buy I understand if you prefer to source items another way.

Пікірлер: 15

@waltersheehey Ай бұрын

Glad I could help!

@BeaulieuTodd Ай бұрын

I haven’t gotten around to installing mine yet. Too much to learn with the cnc alone. This will help. Suggestion… build a dongle loop back plug to complete the alarm loop. When you disconnect the rotary, plug your dongle in!

@UglyDogWoodshop Ай бұрын

Great idea. There's also a method of wiring it such that it doesn't alarm, even without the dongle. It was floated in the Masso forums.

@EdwardKowalski Ай бұрын

Very unique and helpful channel content. Thanks once again.

@UglyDogWoodshop Ай бұрын

My pleasure!

@kenfloyd6541 Ай бұрын

Seriously, I cannot thank you enough I am up and running my rotary.

@UglyDogWoodshop Ай бұрын

@@kenfloyd6541 I'm glad to hear it!

@waltersheehey 12 күн бұрын

If you're setting a z offset off of the MT2 65 tailstock, it's ~28mm. The top of the tailstock is 93mm from the bottom and the live center is 65mm from the bottom. At least those are the dimensions of the one that I bought on Amazon.

@UglyDogWoodshop 12 күн бұрын

I feel like there must be different versions that they sell. I see some with the motor orientation on the opposite side too.

@rrr92462 Ай бұрын

What bit did you use to cut the holes in the 40x20 extruded aluminum? Feeds/speeds? I've yet to cut aluminum on my Elite, so I'm nervous.

@UglyDogWoodshop Ай бұрын

It’s been so long can’t remember the speeds and feeds. I’m sure I started with the Bits N Bits data and slowed it down a little. I used their 1/8” O Flute.