What is the metal bracket holding the dust hose?

Instead of inverting in the software just swap a couple of wires around!

If you're setting a z offset off of the MT2 65 tailstock, it's ~28mm. The top of the tailstock is 93mm from the bottom and the live center is 65mm from the bottom. At least those are the dimensions of the one that I bought on Amazon.

It blows my mind that trim routers are still used on cnc routers and still recommend as a budget option. We burn these things up all the time at work using them as originally intended.

Ok, Everything I do takes an extra step or two. Some are easy fixes, some I have to pull my hair out for hours. lol Thought this on would be an easy fix. NOPE! Grrrrr I couldn't find an option for tool setter after double clicking input 18, and by default was set to High. Hit the spacebar to change to low. But still didn't toggle from High to Low when pressing the tool setter. Grrrrr! Then I noticed Tool Setter on input 11.... Light Bulb Moment. Thats the default 2 Wire Tool Setter Port built into the back of the Masso. So I disabled input 11 and set tool setter to input 18. Still not working? Looking back inside, looks like they have some trickery going on wiring it along with the Probe on input 12? Pull up resistor? Dont know what going on under the Heat Shrink? Do I need to completely disconnect the factory wires for the tool Setter and Probe, Along with disabling them in the masso setup?

I would recommend some good smoke detectors. I would also install some sheet rock over the exposed insulation and wood studs. I imagine a print farm has a higher risk of fire than most uses in a basement.

You dont find the loss in Z clearance an issue?

What size compressor should I looking at to support the dust boot and a ATC system. I bought the dust boot now but planning on getting a ATC system in the future.

Great videos and setup bud

Could you do an air test for the sidekick like you did for the other dust boots?

Had a Woodworker Onefinity for four years now and the Elite just arrived this week. I'll definitely be investing in some taller tool racks from you after I get the ATC purchased.

I was and am still bummed that the Masso isn't Bluetooth gaming controller compatible. Just what everyone needs, another cord to deal with.

Great video. I like to see videos like this of people starting out with small print farms in their basements or garages. Question I have for you what are you doing about the noise level? I just got my 1st P1S and I was amazed at how loud these printers are. I can only imagine how loud having 12 of them would be.

Question. The ATC is on my short list Can I purchase this and use it manually with a side button maybe without having the ATC yet?

Thanks for a very informative video :) May I ask what plate you use and why?

Very cool. I am definitely interested in adding one of these myself…. My only hang up is worrying about how hard it is to square/plumb and level everything to the router/spoilboard

I haven’t gotten around to installing mine yet. Too much to learn with the cnc alone. This will help. Suggestion… build a dongle loop back plug to complete the alarm loop. When you disconnect the rotary, plug your dongle in!

I have the 44 and the 7 that matches. I’d be happy to work with you on this.

You make our lives easier with your products and I dig it. 👍🏼👍🏼

Could have sworn you said you were retired at some point, look pretty busy to me, amazing what you have done, great content. Keep it up Pat

Man I love your vids. I've been thinking about a simple tower light that blinked for a tool change or when an error has occurred. I'm not smart enough to know if the Masso can do it but I'm sure you are. BTW I have the V10 dust boot from pwn. Someone in the 1F fb group suggested a monitor arm on Amazon. I LOVE it. I can move my masso around and it's so much more convenient.

Great information. Thansk for sharing.

Does the spindle have an internal taper? Does it have a hole all the way through?

I am currently using the commercial license. I will look into the start up license. Thank you for the tip!

I've been using the personal version for years and somehow missed the startup license. Thanks for bringing it to my attention!

AutoCad (F360) is notorious for changing licensing terms. The business model seems to be ... get you to use, it then set the hook. I have used 5+ CAD/CAM packages during my career ... UG NX, Catia, Calma (yes I'm old). As a retiree I use the open source code FreeCad (Ondsel, the commercial version with collaboration added). FreeCad is a parametric 3D CAD modeler. By default, you store all your files on your local machine, and the files are plane text. The CAM module supports: - 3D surfaces, - supports Automatic Tool Changers - introducing REST machining - fixture support .... so you have 4 identical parts you want to make, using G54,G55,G56,G57 it loads bit 1, cuts all 4 parts in sequence, then loads bit 2 and repeats Yes I am a FreeCad fanboy. I am even trying to add code that explicitly supports the Masso controller.

Since it is all in the cloud you are at the mercy of their terms. This may not be important to you, but I think it should have been mentioned.

What machine?

Now thats nice!

You are doing great things for the CNC community. Thanks!!

Nice to meet you

I appreciate your thoroughness on how to install the pendant but you never explained why I need the pendant (title of the video). There are plenty of videos on how to install but I thought you had something else to offer.

@UglyDogWoodshop I'm currently working on a z independent dust boot that is compatible with an ATC for the onefinity elite foreman. I've gone through several iterations of designs, and I can say that it is absolutely possible to create a boot with 360 deg. brushes. Based on my own testing, I can see three problems with this design. 1. The missing brush defeats the purpose. I can't imagine this will be effective. 2. The boot wraps tightly around the spindle, which will greatly reduce air volume as the spindle moves down in the z-direction. I know this from first-hand experience since I tested a similar design. Would love to understand how you solve this. Im assuming you have an air port that doesn't conflict with the spindle? 3. This system makes use of a pneumatic cylinder, which means that the boots' z-axis position doesn't adjust to the length of the cutting tool. While you mentioned the ability to adjust the z height, this is still a manual process, which defeats the purpose. My design accounts for all 3 of these issues. I only mention these because I encountered them while going through iterations of my design. With that said, I appreciate the designs that people are coming up with. Please note that this isn't meant to bash your design. Just wanted to point these out. Hopefully, we'll see improvements in future iterations.

nice set-up!

What bit did you use to cut the holes in the 40x20 extruded aluminum? Feeds/speeds? I've yet to cut aluminum on my Elite, so I'm nervous.

Thank you for sharing the file. I know how much work that is to make. I would love to see how you made the vertical table. There is not a lot of information out there.

in the video you say you use 20 mm dogs. What diameter holes did you cut for the dogs so there is some gap to insert and remove the dogs? The DXF file has 19.82 mm holes for the dogs. Is the DXF file intended to be used with 3/4" (19.05 mm) dogs?

I wish I had seen this video a month ago. I tried something similar to this using Microjig Dovetail fixtures instead of T tracks and made a whole pile of mistakes. Now I know better for the next time.

Very unique and helpful channel content. Thanks once again.

Glad I could help!

For the Masso controller, if you populate the “Parking”, on the F4 screen, Work Offsets to the X and Y of your desired park position, then in the post processor (in Fusion), enter the GCode command G30 at the end of the job, the Masso to command the spindle to your requested park position at the end of the job.

another good tip. thx! btw, wondering which .cps u use, & where located.

awesome tip!

I'm not getting the voice audio, but I"m getting the sound effects for the subscribe click.

What is the function of the clear section?

Just got my atc setup done. This is my 1st cnc, I had to learn a lot just to get it up and going. Now at least I get to play while learn. lol. I got the V9 but before even trying it I was unhappyy with it. Im sure its a great design for non atc systems, but not the best for atc. I wish this came out a bit earlier. I recently bought the Double Barrel boot about a month ago. Just installed it this morning. If its not up to task, this will be the next option. Great designing, with extra credit for originality.

Love the idea I need this for my shapeoko 5 pro with Masso controller is a retro fit possible ?

I don't need a tower light, everyone knows when my CNC is on or off. But, it depends on how noisy the surroundings are really.

Please make one for cncdepot spindles