Install the PERFECT Subfloor | Ram ProMaster Van Build Series | Van Life

Install the PERFECT Subfloor | Ram ProMaster Van Build Series | Van Life | Solo Female Traveler

Рет қаралды 42,679

Күн бұрын

In this video I share how I installed my subfloor. I cover things like making a template out of cardboard, transferring the template onto plywood, waterproofing the subfloor and more.
Tune in to my next video where I'll be installing my furring strips on the walls of my van with plusnuts!
Until then, be sure to subscribe to my channel and turn on notifications so you don't miss a beat.
For more frequent van life updates, connect and interact with me on Instagram and Tik Tok @LaurenLawliss.
Instagram: / laurenlawliss
Tik Tok: / laurenlawliss
Thank you for your support - Venmo: www.venmo.com/u/LaurenLawliss
What questions do you have for me?
Let me know in the comments below!
Thanks for being here :)
LINKS TO PRODUCTS AND TOOLS BELOW!
Timecodes
0:00 - Intro
0:33 - Making a Cardboard Template
5:11 - Transferring the Template to Plywood
6:35 - Cutting the Plywood
7:43 - ProMaster Floor Lift
9:51 - Removing Factory Installed Tie Downs
11:11 - Fastening Options
13:40 - Sanding & Water Sealing
14:57 - Addressing Subfloor Insulation
16:27 - Closing
Affiliate Links for Products and Tools
Thompson Wood Water Seal - amzn.to/3JysDjr
Jigsaw - amzn.to/3vsO1AL
Skill Saw - amzn.to/3oJojnS
Orbit Sander - amzn.to/3oIFAxf
Belt Sander - amzn.to/3BrZYKN
40 Grit Belt Sand Paper - amzn.to/3cX9Hi0
180 Grit Disk Sand Paper - amzn.to/3cJicgi
Corrugated 36" x 72" Cardboard Sheets - amzn.to/3BvY7Ew
Box Cutters - amzn.to/3zoByPw
Painter's Tape - amzn.to/3Sfxdqv
Safety Glasses - amzn.to/3JlflGF
Disclaimer: I am not a professional. This information is what I have gathered from my own research on the topic and is only intended for reference. Further research should be conducted for your specific project based on your needs. Please note, not everything you see online is the correct or the only way to do something. Contact a professional if in doubt. Following an incorrect procedure could lead to a dangerous and ineffective result.

Пікірлер: 195

@randy909 2 жыл бұрын

I'm impressed by the the amount of research you're putting into this build. Your videos are very informative.

@LaurenLawliss 2 жыл бұрын

Thank you!

@PazmanBC Жыл бұрын

You could also use those 8 anchor points to at least secure the floor down enough to prevent any shifting without adding additional holes & then let gravity do the rest.

@LaurenLawliss Жыл бұрын

Sure can! I made sure to mention that in the video.

@davidofcoburg9279 Жыл бұрын

Hey Lauren, we're an older (really old) Aussie couple with a factory built campervan on order, we would have loved to do what you are doing but for us its way to late to do a self-build. We've been following Jimmy and Natalie with their build and came across your channel this morning so we are looking forward to following you both. Great job on the windows BTW, we reckon its fantastic that you are taking this on alone, clearly you are confident and capable. Downunda - Melbourne Australia

@LaurenLawliss Жыл бұрын

Awh, thank you so much for your kind words. Welcome to the channel and enjoy your camper van when it comes in!

@GustavoDCarro 11 ай бұрын

❤

@LaurenLawliss 10 ай бұрын

🤩

@michaelvinalon3415 10 ай бұрын

The 1st 30 seconds I learned how to get the template and do the cuts around wheel wells and bulkhead ! Thanks !!

@LaurenLawliss 10 ай бұрын

Wahoo! Best of luck with your subfloor. You got this🙌🏼

@gonewiththekale 10 ай бұрын

I feel fortunate to have come across your channel yesterday, been binge-watching since. So glad to see your subfloor idea because I am tall too. Your videos are fantastic, thanks for teaching us how to do this🌟🫶🏼💥💯❣

@LaurenLawliss 10 ай бұрын

Thank you for the kind words! I really appreciate it and am glad you found it helpful. Best of luck with your subfloor, you got this🥰💖

@EcoNeato 15 күн бұрын

Some builders coat the factory painted metal floor with a waterproofer to prevent rust prior to plywood. Maybe there should be at least one drain hole in case of water leak, but would need to have a varmint screen.

@vickimathews1970 2 ай бұрын

I'm with you, that's all I do, I don't even have anything attached to the Wallsor ceiling, everything is holding together from floor to ceiling and end to end, and I've driven on major dirt tracks around Western Australia and Tasmania, the windy roads take a toll more than the dirt roads...lol

@LaurenLawliss 2 ай бұрын

Yup! Cabinets will hold then in place and once I added my furring strips that also blocked the floors from being removed.

@scottmitseff4402 8 күн бұрын

Beautiful presentation and very Professional work thank you for sharing your project I learned a lot

@LaurenLawliss 5 күн бұрын

I appreciate the kind words 🫶🏻

@user-pk3bs4mg1t 9 ай бұрын

HI Lauren! your videos are so so informative! As a solo female about to embark on my own diy build, your strengthening my confidence this is something i can actually accomplish!! Great videos, thanks again!!

@LaurenLawliss 9 ай бұрын

Hey! Thank you for the comment and kind words🥰 I am so glad you feel more confident to build out your own van. I have no doubt you can do it. Best of luck🙌🏼

@Diizkraze 2 жыл бұрын

nicely done lauren 🥰 great job doing your floor. cannot wait for another upload. 😁

@LaurenLawliss 2 жыл бұрын

Thank you!!!

@ellaforbes-ackers9104 8 күн бұрын

This is such a god and helpful video!! Thank you so much 😊

@LaurenLawliss 5 күн бұрын

Thank you! Glad you found it helpful.

@edwardcunningham6315 11 ай бұрын

Beautiful, the job and the installer 😁👍. Your right, the end product is only as good as the foundation it's built on. I'm remodeling an old RV and I opted to do the Sub floor in seventeen thousand pieces (😀 just kidding) I split the floor into four sections in the back and two in the front cab. It really was a bear of a job getting the edges just right, but boy it makes the rest of the install so easy when you have symmetrical edges to go to. Keep recording and we'll keep watching and learning 😊👍❤️

@LaurenLawliss 11 ай бұрын

Thanks for the comment, Edward! Sounds like you have a fun project on your hands too. Wishing you the best of luck😄

@glendahill Жыл бұрын

Another excellent video. You are now my official 'go to person' for van conversions!

@LaurenLawliss Жыл бұрын

Appreciate it!

@petegilbert6886 2 жыл бұрын

Another great video for DIY van converters to follow! 😎👍

@LaurenLawliss Жыл бұрын

Thank you!!😊

@leerfarmer 2 жыл бұрын

Looks Great, thanks for sharing‼️

@LaurenLawliss 2 жыл бұрын

Thanks!

@NoStressVanLife Ай бұрын

Great Work! Love the floor!

@LaurenLawliss 17 күн бұрын

Thank you!!!

@larryjackson7027 Жыл бұрын

Great job Lauren! One of the best van build series on KZfaq.

@LaurenLawliss Жыл бұрын

Thanks, Larry! That means a lot🥰

@JJsAttic 2 жыл бұрын

Looks good thank you for explaining everything in great detail. once again good video looking forward to many more

@LaurenLawliss Жыл бұрын

Thank you!

@user-kf9fv1qj9u 5 ай бұрын

Great video Lauren

@LaurenLawliss 5 ай бұрын

Thank you!

@gwb8445 6 ай бұрын

Excellent video. I went without a subfloor - just the factory rubber mat that came with the van and a throw rug over it. Worked fine for me.

@LaurenLawliss 6 ай бұрын

Nice! Glad it’s working well☺️

@regulardude2011 2 ай бұрын

You are incredible! Some of the best videos I have seen pertaining to van builds!

@LaurenLawliss 2 ай бұрын

Appreciate it!

@anwest728 2 жыл бұрын

Well done Lauren. For someone with little experience you are doing a great job. I've watched all your videos. looking forward to your next video

@LaurenLawliss Жыл бұрын

Thank you so much. Appreciate the support.

@Barry_BredaNL Жыл бұрын

Hello Lauren, I just subscribed to your channel, looking forward to seeing your new home on wheels take shape. I am impressed with how accurately you explain everything in detail! Good luck with the next steps in building, the result is sure to be beautiful and comfortable! Greetings from the Netherlands, Barry

@LaurenLawliss Жыл бұрын

Thank you for the kind words! Excited to have you here for the journey.

@LockerMart 2 жыл бұрын

Always well done. Both the work product and the video presentation.

@LaurenLawliss 2 жыл бұрын

Thank you! I really appreciate it.

@baddog340 2 жыл бұрын

I enjoyed your video and I'm very impressed at how smart and thorough you are. I went ahead and hit that like button and subscribed. Looking forward to seeing more.

@LaurenLawliss 2 жыл бұрын

Thank you for the support!

@christine9604frisco Жыл бұрын

Liked this video.

@iguardian1 2 жыл бұрын

Thanks, Lauren. Very professional, I'm betting Professionals are taking tips from you😂 I love your videos and there's something calming in the tone of your voice that I like. I would've done the same thing with the floor, a "Swiss-Cheese" floor can't be good for the van in the long run, and as you mentioned "Rust" As always I'm looking forward to your next video🥳Stay well until then😘

@LaurenLawliss 2 жыл бұрын

Thank you! Appreciate the support and you joining me on this journey :)

@Ms.Frankenbuilder 2 ай бұрын

Another helpful video, thanks.

@LaurenLawliss 2 ай бұрын

Glad you found it helpful!

@johnlarson4623 2 жыл бұрын

Well you had a lot of thought in the floor and it come out wonderful it's nice to see somebody that thinks things through wish you the best have a wonderful year take care from the old guy 😇🌞☕.

@LaurenLawliss 2 жыл бұрын

Thank you!

@jessieanddavid Жыл бұрын

Really great advice! Thank you for the tip on the lift 😊

@LaurenLawliss Жыл бұрын

Thanks!

@AB-C1 Жыл бұрын

Hi Lauren, Fantastic video! Your explanations are spot on! Great work the measuring cutting and your solutions to this layout issues are great and well thought through! You clearly have an analytical problem solving mind like me which I loved I'm a bit OCD too lol.. Also I love your voice very calming could listen to you all day! Lol (Just a tip for teh exposed metal and holes, I'd have sprayed some sort of Anti rust into any holes and cavities, screw threads, before theyre blocked off! Whether one that dries or a grease to keep moisture and air out) As all vans rust over time! Like where the screws are, you used to fill the holes in the floor, with a thin coat of either paint or something like an anti rust spray or grease, to seal the metal would be a good idea! Also like when you fit your heater and things underneath and also the cavities in the side panels anti rust spray is always a great prevention measure.. ..You may be ok? BUT given you're living in the van there will be more Moisture and also it's going to get used and be your home, so ANY EXPOSED metal inside and outside should be sealed with an anti rust and paint also ideally if it shows/exposed, like when you cut the metal for vents windows etc. Not sure if you have already as I see your windows are fitted and this is the first video I've seen of yours. Can't wait to follow your build! Thanks again for making such a great video! You're very intelligent and easy to listen to! You've really put a smile on my face today and given me extra motivation and tips for when I do my own build! Cheers from London England 👍😉🙂😎🏴󠁧󠁢󠁥󠁮󠁧󠁿 x

@LaurenLawliss Жыл бұрын

Totally agree. I am very paranoid about rust and have been using rust oleum heavily in my van wherever there is exposed metal. I will be sure to add them to the holes as well! Thanks for the insight. Glad to have you along for the journey and appreciate your kind worlds😁 good luck on your own build

@dougsagon2156 2 жыл бұрын

Congrats on the sub floor install. Looking good. Nice that you have a large shop area to work in. You obviously know your way around a shop.

@LaurenLawliss 2 жыл бұрын

Thanks! Learning as I go for sure but enjoying every step.

@MrDwinstead 2 жыл бұрын

Awesome video as usual, Lauren. Really helps me down the road for when I do my RV remodel. Envious of your baltic birch.😉

@LaurenLawliss 2 жыл бұрын

Thank you :) Best of luck with your RV remodel. And yes, I am so grateful to have found my baltic birch!!!

@themetalmaiden7462 2 жыл бұрын

Awesome video as always. Can't wait for the next one 😉 And that pencil in the stick idea......genius.

@LaurenLawliss 2 жыл бұрын

Hahaha thanks! It made stenciling so much easier🤩

@LorenzoMarch 2 жыл бұрын

Very creative

@DavidHuffTexas 4 ай бұрын

Clear, informative, and well-presented. Kudos! Also hooray for the shoutout to Humble Road!

@LaurenLawliss 4 ай бұрын

Thank you!!

@user-kf9fv1qj9u 5 ай бұрын

Good luck renovating your van Lauren

@LaurenLawliss 5 ай бұрын

Appreciate it.

@Rudy1150 11 ай бұрын

wow. This maybe the most professional diy series ever made. And ever time I wondered "why did she do it that way" you seemed to have answered my question. Thank you for sharing your knowledge!

@LaurenLawliss 11 ай бұрын

Thank you, Rudy! I’m glad you found it helpful. Best of luck with your build🥰

@saleemalamri9719 2 жыл бұрын

Bravo 👏🏻👏🏻👏🏻

@RiDankulous 3 ай бұрын

You are very comprehensive as seen in your electric system install video. Your chosen mod procedures are excellent. I got nervous when i saw the regular videos end I believe about 6 months ago. It was nice to see some shorts about your travels. They are great! I probably won't do such a build i the future but who knows. I don't dislike large spaces but I enjoy living in a small, fairly simple abode.

@LaurenLawliss 2 ай бұрын

Thanks for watching and commenting! More videos to follow… eventually 😆

@RiDankulous 2 ай бұрын

@@LaurenLawliss That's fantastic!

@1fredricka Жыл бұрын

very helpful and informative. Your details are excellent Thank You for a excellent pro master video. I will enjoy following your build and will now subscribe.😊

@LaurenLawliss Жыл бұрын

Thank you! Welcome to my journey😊

@ronaldseitz3677 2 жыл бұрын

Very nice work on your sub flooring lauren

@LaurenLawliss 2 жыл бұрын

Thank you😊

@imrikkibobbi 25 күн бұрын

i'm at a loss, you are literally doing everything I did .... our mindset is so nearly identical and to me brilliant ... i'm at a complete loss as I did these things back in 2017 before taking off on the most hilarious road trip as at the last second while hitting refresh for the 100th time got the Fest Passport and leaft for an 8 day trip and didn't come back till 104 days later

@LaurenLawliss 16 күн бұрын

How funny!

@Eyesis_1 2 жыл бұрын

Very nice and call me crazy, but I actually like the color of that sealant on the plywood. Stay safe and TFS💖

@LaurenLawliss 2 жыл бұрын

Honestly same😅

@josephfalcone9569 10 ай бұрын

I am very impressed with you build you are one smart lady great work.

@LaurenLawliss 10 ай бұрын

Thank you!! I am very proud of it myself😁

@josephj7991 2 жыл бұрын

Very good job! I see so many van builds over build the Floor and insulation! I went the same was as you did, 15/32" OSB 1/4" rubber mat. I mite go w vinyl lam floor but things wud slide around on that? They stay put on the rubber floor so...

@carls4552 2 жыл бұрын

Maybe it's just the camera but that sub-floor looks good enough to be the finished floor. Nice video Lauren.

@LaurenLawliss Жыл бұрын

Awh thanks!

@rickeydenler2385 Жыл бұрын

I had a friend in his dad built boat docks and they used a bug sprayer to spray on Thompson Water Seal fast and quick

@LaurenLawliss Жыл бұрын

That would be handy!

@vickimathews1970 2 ай бұрын

The tie downs are a perfect way to hold the sub floor down

@LaurenLawliss 2 ай бұрын

If one would like to go that route they certainly can. I don’t see the point in securing the subfloor down since all the cabinetry will go on top and hold it in place. But to each their own 😊

@bknnacerch2m721 2 жыл бұрын

You are great and brilliant keep on

@LaurenLawliss 2 жыл бұрын

Thank you for your kind words!

@bknnacerch2m721 2 жыл бұрын

@@LaurenLawliss 💪

@LaurenLawliss 10 ай бұрын

🤩

@NotMe-st8qc 3 ай бұрын

Baltic birch has fewer voids in the wood and is a good choice for a floor.

@LaurenLawliss 2 ай бұрын

It’s the best!

@albertofernandez6814 2 жыл бұрын

Great video!! Are you sure you are not a professional at this kind of work? Keep it up and your viewers crave more frequent videos..😜😜😜

@LaurenLawliss 2 жыл бұрын

Hahaha thanks! Learning a lot as I go and I’ve done tons of research😄

@jamesray3920 9 ай бұрын

I got Lucky my van had some kind of removal mat i wil, use as a template to build my floor 😊

@LaurenLawliss 9 ай бұрын

That is perfect! Slightly jealous😉

@smokey6885 2 жыл бұрын

THE FIT OF YOUR SUBFLOOR LOOKED PERFECT. I DON’T THINK IT COULD HAVE BEEN DONE BETTER. GOOD JOB, LOOKING FORWARD TO NEXT UPDATE

@LaurenLawliss 2 жыл бұрын

Awh thanks!!

@arevalo8804 Ай бұрын

Love your videos. Wish there were more women out there like you. Hands on and not afraid to get dirty. Kudos to you Lauren!

@LaurenLawliss 2 күн бұрын

Appreciate it🫶🏻

@amyf5948 Жыл бұрын

As a solo female about to start her Promaster Build I’m so happy to have found you!! So appreciate your attention to detail in your videos when explaining things!!

@LaurenLawliss Жыл бұрын

Best of luck with your van build!!

@josephj7991 2 жыл бұрын

The floor isn't a problem, a bare metal floor wud be Cold but wood solves that! Just sear socks and or slippers if chilly?

@christinamann3640 Жыл бұрын

Depends on the climate you are in

@jasonjones5213 2 жыл бұрын

Good video, and good information.I never understood why you would insulate the floor anyway.Especially being as tall as you are.

@LaurenLawliss 2 жыл бұрын

Thanks! And yes, I’d much rather have space to stand up than insulate for a marginal temperature difference. Socks will have to do😄

@rickeydenler2385 Жыл бұрын

A raised panel router bit would take care of that little raise on the back of your plywood

@LaurenLawliss Жыл бұрын

For sure!

@katekaos Жыл бұрын

I’ve heard insulation doesn’t do much so good choice I’m not doing the floor. Some people don’t even do the walls and ceiling. My van came with a factory floor I’m leaving but I came here to figure out how to get the stupid tie downs out. My drill bit won’t work and Allen key doesn’t have a handle. They’re so hard. I try a socket today. If not I’ll get a Allen wrench with handle. Good job on your floor!

@LaurenLawliss Жыл бұрын

Hey! Thanks for the comment. I am so glad I didn’t insulate my floor and left more headspace. The tie downs in a Ram ProMaster requires an M8 torx bit. They can be challenging. I struggled with a few of them for some time but got it to eventually budge. The socket should help. Good luck with your build!

@katekaos Жыл бұрын

@@LaurenLawliss thanks! I got the impact bit - it’s a T40 or 3/8 thingy but the drill isn’t an impact drill so it was spinning on me. I need a handle for Allen key - 4.5 size but the socket bit arrives today so maybe that’ll work. If not the dealer can do it cuz mine are so tight 😭. Thx! I can’t wait til the van is functional!

@LaurenLawliss Жыл бұрын

@@katekaos Glad to hear you got it figured out☺️

@neilfishingcamp Ай бұрын

Wear some mask. You dont want to inhale those sawdust. Too late but for your future projects. I love your content. First time seeing an intensive camp van build. ❤

@xart23x 3 ай бұрын

Impressive work and execution. Cute girl with ocd driven work?…all for it. If you’re gonna do something, might as well do it right. And looks like you are. Inspiring work, thank you for sharing.

@LaurenLawliss 2 ай бұрын

Thank you! Exactly, doing my research, using high quality products and taking my time. It paid off in the long run.

@laurelanderson-rostami109 11 ай бұрын

Thank you Lauren for putting the work into creating this! For the lip issue you cut that inch off the board so it would lay flush? Then you did what with the inch of remaining board? I looks like it was glued down beside it.

@LaurenLawliss 11 ай бұрын

Thank you for the sweet comment! Yes, in hindsight, if I had to do the subfloor over again, I would cut an inch off on both sides. Even after routering the sides, it still didn’t sit flush fully - which I didn’t realize until after I posted this video. You will likely have cabinetry that will cover it up anyways - my bed boxes do - so you wouldn’t even be able to tell. Hope this helps! Best of luck with your build. You got this🤗

@laurelanderson-rostami109 11 ай бұрын

@@LaurenLawliss Thank you Lauren that is very helpful and seeing you do this is helping me to get this. I am very grateful for you!!

@LaurenLawliss 11 ай бұрын

@@laurelanderson-rostami109 appreciate it🥰

@MeikoEliasXavier 5 ай бұрын

Hey there! Which jig blade did you use to cut the birch?

@LaurenLawliss 4 ай бұрын

Hey! I used a standard wood blade from a local hardware store😊

@davidterrie7661 Жыл бұрын

Why did you use an M8 bolt instead of the factory bolt? I'm about to go pick up a T-40 torx bit that of course didn't come with the bit set I purchased. First panel cut, but still needs a little shaved off here and there. 3/4" sanded birch is heavy. BTW, I painted the interior with ceramic insulating paint that's used on commercial buildings. Should help.

@LaurenLawliss Жыл бұрын

Hi David👋🏻 I’m trying to remember my exact reasoning. I think the factory installed bolt couldn’t be detached from the tie down or it sat too high and interfered with the subfloor. But I could be mistaken. Nice work and good idea. Thanks for sharing!

@alaskalogcabinyoga7050 Ай бұрын

Great job! I was wondering about the Thompson Water seal. I used it on my subfloor and furring and now I’ve been reading that it’s only for exterior and it could be harmful to health in interior wood. So now I’m worried. What are your thoughts?

@LaurenLawliss 2 күн бұрын

Appreciate you sharing your findings. I am not aware of this, but don’t doubt it could be true. I hope it’s safe 🤞🏼

@newman_LaRue_Jr 2 жыл бұрын

Remember to check pockets in the walls and doors for any loose items from previous owner you won't be sorry

@LaurenLawliss Жыл бұрын

Thankfully I purchased this van brand new but great call out for those with used vans!

@user-oi1cl1km3t 10 ай бұрын

💚❤

@LaurenLawliss 10 ай бұрын

💖

@ya472 3 ай бұрын

Thompson's Water Seal has been a product I was told to stay away from. Apparently it is emulsivied wax, which works against using any other product. Durability of wax is limited.

@LaurenLawliss 2 ай бұрын

Thanks for sharing!

@wchrisg0528 2 жыл бұрын

Is that 7 ply furniture grade Baltic birch for the subfloor?

@LaurenLawliss Жыл бұрын

Yes, it is 1/2 inch baltic birch plywood with 9 layers. Pricey for a subfloor, I know, but durable and less likely to warp🤩

@Van-life-4-Jesus 3 ай бұрын

Hey Lauren, my promaster came with a fitted black matt can i use that? Its like 1/8 of an onch from the edges idk if that matters or not

@LaurenLawliss 3 ай бұрын

Lucky you! I’d recommend removing that and using it as a template. Will save you a lot of time 😄

@Van-life-4-Jesus 3 ай бұрын

@LaurenLawliss is ir the 100% exact size I need? Cause it dont seem to go to the end? Or maybe im tripping Thanks for the reply

@LaurenLawliss 2 ай бұрын

I have never seen the fitted floor mat in person and assume it varies year to year of the vans make but if it is form fitting around the edge of the floor, I don’t see why you can use that and then make minor adjustments as needed 😊

@shelly2024blessings Ай бұрын

Would placing strips of Thinsulate in the channels help with insulation?

@LaurenLawliss 2 күн бұрын

I did to help limit thermal bridges. Although, the insulation won’t fully eliminate thermal bridges, I’d like to think it still helps, especially with sound.

@fernwehchronicles193 10 ай бұрын

What length and thread would you recommend to put those bolts into the holes in the floor?

@LaurenLawliss 10 ай бұрын

Great question. They are an inch and a quarter long, M8 bolt☺️

@fernwehchronicles193 10 ай бұрын

20 thread? @@LaurenLawliss - 20 thread?

@LaurenLawliss 10 ай бұрын

To be honest, I don’t recall😕

@davidterrie7661 Жыл бұрын

How has your decision to skip insulation and not glue down floor worked out? Any rattling/squeaks?

@LaurenLawliss Жыл бұрын

Hi David! Thanks for your comment. My subfloor is so quiet. There are no noises when I walk on it or drive. I don’t regret my decision not to insulate the floor. Heat rises so the floor is always going to be cooler. To combat this, I am installing a 12v floor heat pad under my final flooring, I’ll wear socks, lay a rug and turn on my heater in the winter months. These “extra” steps (which I would be doing regardless if my floor was insulated or not) are worth saving the headspace and not insulating since I am tall. Hope this helps. Let me know if you have any other questions🥰

@davidterrie7661 Жыл бұрын

Lauren, I've been driving around with my 3/4" sanded ply and small coin top layer on and my floor rattles a lot. I've even cut out a spot where an uneven rib was causing the floor not lay flush at the seam. This, of course is with no weight on the floor. Did your floor rattle before you put weight on it? I'm concerned that my van's floor is not even enough to make your approach work, and I really want it to. Some 80/20 for the power system bed platform and storage is on the way and my Explorist components and batteries have arrived, so there will be no going back soon.

@LaurenLawliss Жыл бұрын

@@davidterrie7661 Hi David! I am sorry to hear your floor is rattling. My subfloor has never made a peep. Just a few thoughts… maybe it is too tight to the the van - add at least a 1/8 inch gap around the entire perimeter of the subfloor. Is the coin top glued down? Is the subfloor touching the M8 bolts underneath? I am trying to think of other ways to troubleshoot the floor but nothing is else coming to mind right now besides those possibilities. I hope you find a solution soon. Best of luck!

@jeremyhaye5759 Жыл бұрын

👍🤟😊

@vinceocratic 4 ай бұрын

Does you Promaster have high and low spots on the floor or is it even? If there are varying heights in the ribs, how did you handle this?

@LaurenLawliss 4 ай бұрын

Yes, there are ribs that run across the floor. But the high spots are all equal so I just rest my boards on that and have had no issues ☺️

@vinceocratic 4 ай бұрын

@@LaurenLawliss just finished my subfloor. What a headache… question for you: did you van come with a cockpit/cargo partition? If so, did you have to purchase the trim pieces to fill in the spaces beneath the ceiling storage piece and aft of the side airbags?

@LaurenLawliss 2 ай бұрын

Glad you got it done! I did not order my van to come with a partitioner so I’m not entirely sure what you’re referring to… sorry.

@johnadams673 11 ай бұрын

I can't even imagine how loud this is. If you are watching this video, don't do it this way. Construction adhesive wood straps between the floor ribs. Then Wood glue and nail the subfloor to the straps, won't rattle when driving or sqeek when walking

@LaurenLawliss 11 ай бұрын

Honestly, my subfloor has NEVER made a sound. It is so quiet when I am driving and walking on it. I opted out of doing wood strips and adhesive in the floor ribs because that limits air flow under the subfloor which is essential for any moisture that will inevitably end up under there. Also, there is no need to screw the subfloor down to anything - it won’t move once you have the cabinetry installed on top - even in a car accident, that’s how much confidence I have in the way I secured my cabinetry. Thankfully there are multiple ways to build out vans and this is one of the many ways to do your subfloor. If it would give you a better peace of mind to install it with wood strips then go for it. But the added weight, time and money to do it that way for no added benefit wasn’t worth it in my option☺️

@marquisdesade6191 2 жыл бұрын

I insulated from the bottom of the van. I spray glued panels up and spray foamed around the edges to be sure they won't come off. I left the shiney side out. It makes a noticable difference, more in the summer on parking lots to my surprise.

@LaurenLawliss 2 жыл бұрын

Very interesting. Thanks for sharing!

@user-kn4mm8tx6y 8 ай бұрын

Living in heart.shamim zahuri,ban🤴✌🤝👏

@LaurenLawliss 8 ай бұрын

👋🏻

@stefanomartano4032 6 ай бұрын

good, but you should have insulated the frame before the floor

@LaurenLawliss 6 ай бұрын

You certainly can but it didn’t make sense for my wants and needs. Currently in 19 degree Fahrenheit and don’t regret my decision - but that’s me😁

@clarekelsey2774 2 ай бұрын

HOW About an update on well the floor is working - any underlying moisture issues - w/time comes more info. thx.

@LaurenLawliss 2 ай бұрын

No issues with the floor! If I had to do it all over again, I’d do it the same exact way 😊

@clarekelsey2774 2 ай бұрын

@@LaurenLawliss thanks!

@jcnredpizzawindow2219 7 ай бұрын

No insulation?

@LaurenLawliss 7 ай бұрын

Nope and I explain why in the video☺️

@lawrencepartington8448 7 ай бұрын

Lauren, with a year to reflect back on your decisions, do you have any regrets about not insulating the subfloor? Your reasoning makes total sense to me but I wanted to give you a chance to re-consider before I copy your no-floor-insulation strategy. Thanks.

@LaurenLawliss 7 ай бұрын

Great question! And my answer is zero regret - I’d do it the same way over and over. I am currently up north where there is snow and it’s 30 degrees Fahrenheit and I have no complaints. Save the time, money and headspace!

@tracker9 2 ай бұрын

I have no idea what you did with the pencils and cardboard.

@LaurenLawliss 2 ай бұрын

The cardboard was a stencil of the floor to trace onto the plywood once I had it fined tuned. The pencil in the board helped me get the curvature of the van floor 😄

@Michael_Francis_Gray Ай бұрын

Are you still in the van life? want a companion for the road? 😘

@LaurenLawliss 16 күн бұрын

I am still solo van lifing!

@samsungtaco11 2 ай бұрын

So, if you're not insulating the floor, why have a subfloor? I would just go with a bedbug and be done with it.

@LaurenLawliss 2 ай бұрын

To have a flat surface to work on and to secure my cabinetry to the subfloor with screws along with the furring strips on the wall.

@samsungtaco11 2 ай бұрын

@@LaurenLawliss awesome build. I'll be referring to your videos when I build mine. 👍

@LaurenLawliss 2 ай бұрын

@@samsungtaco11 appreciate it! Good luck on your build ☺️

@AprendizDeLoQueToca 10 ай бұрын

You seem to like quality. You need a microphone attached to your clothes to improve the audio.

@LaurenLawliss 10 ай бұрын

Yes, quality is a top priority for me. Thanks for the feedback. I agree and have been using a microphone for the new videos to come. Big difference🤗

@EcoNeato 15 күн бұрын

Promaster has the lowest interior height and since I'm 6'4", I could never deal with a ProMaster and therefore have had a Sprinter and now Transit (high roof). I think the 2024+ ProMasters now have higher ceilings, but are still not as refined as a Transit or Sprinter and therefore cheaper.

@user-yg8tq6cd1m 5 күн бұрын

😂 You're just paying extra for everything because it's a Mercedes

@TradeCrypto 11 ай бұрын

how are you cute!?

@LaurenLawliss 11 ай бұрын

My dad would you tell I get it from him🤷🏼‍♀️

@ronniegarcia3885 7 ай бұрын

You are beautiful, Lauren. I am not sure if you are married

@LaurenLawliss 7 ай бұрын

Thanks

@ricusserfontein1086 Жыл бұрын

So weird to see young people being able to do this and afford vans like these. Here in South Africa these vans are million rand vehicles few private people can afford.