Ride safe Idol

Yes he is from philippines😃

Not sure Idol pero try mo mag tingin sa shopee

long press both the "+" & "-" button until you enter the calibration mode, then you will notice that the kph or mph will blink, then to change it just press the "-" button to change it, after that do not press anything then the flashlight will save the changes automatically after a few seconds of not pressing anything

Hindi ako sure lods, try mo nalang tingin sa shopee baka meron,

usually kase lods dapat may charge siya mga halos d nalalayo sa 50% para hndi masira battery kapag naka tabi

hindi ko masyado kabisado idol, pero madami sa google, dpende din kase sa sukat and kapal ng gulong

Cable tie siguro boss, kaso hindi ko lang sure if maganda tignan boss

wala naman din nasabi lods basta tama ung input ng size ng gulong mo, ung speedometer na ung mag cocompute,

Disconnect niyo lang yung sa speedometer mag o auto standby lang siya idol,

@@boonbox12 idol mara ming salamat po. Tapos bilis mgreply hehe. More power po and more videos, nakakatulong ng marami 😊

@@boltzcorsino7782 thank you po 😊

Ok lang naman kung maambunan lods pero mas maganda kung hindi lalo na sa ports (charging / horn and speedometer) baka kase masira agad, kapag ung mga parts na un ung mapasukan ng water

hindi siya lods basta i ipit mo ng maayos sa spokes

@@boonbox12 oy po lods bak maka bili pp eh salamat sa info

Depende po kung malubak sa dinadaanan pero pwede naman po lagyan ng kahit anong pwede ipang palaman sa gitna, mas maganda kung medyo madikit din para may kakapitan like double sided tape etc,

@@boonbox12 ok salamat po,san po kinakabit yung horn

@mrzombies1868 kahit san position basta comfortable ka na abot mo tsaka kung saan position maganda ung maiilawan ng flashlight

The display will automatically go to sleep mode when no input in the sensor, What i do is disconnect the sensor temporarily.

Yes

ayaw ba gumana kahit malapit na? make sure po na aka connect yung wire mabutj, medyo matigas po kase isaksak yung sakin sa flashlight

Hindi po ako sure lods, pero ung saksakan ng buzzer merob rubber seal lods, and kung sa ambon ok naman siya, wag lang hayaan mababad siguro

@@boonbox12 ah sge po salamattt

welcome po idol

@@boonbox12 pero gumagana pa lods?

yes lods goods pa ung sakin up til now, medyo bumibilis nga lang ma lowbat dahil matagal na din nagagamit

Unplug lang po yung yung pindutan, tama po ba?

Try long pressing the power button until the light come off

Well, there is a separate walkthrough video with the adjustment of wheel size, while this video is only for the mounting of the device itself. But let me help you with it, First press and hold the + and - sign at the same time until the km/h or mi/hr blinks, And then ( - ) to toggle, and (+) to go to the next configuration. After selecting the desired speed unit Press the + button then you will see the 208 (in cm) blinking on the screen, and unfortunately, that is the minimum wheel circumference for this speedometer, and to adjust its size, press the (- )button, you can also long press it to make the increment faster. But just in case you input the wrong size (bigger size), instead of long pressing the (-) sign, you can simply just Dont press anymore button, then after a few seconds it will save the configuration and will go back to its original state, Then just reconfigure it again. This is way faster than waiting for the circumference of the wheel to reset because there is no button for decrement. I hope this helps, have a good one 😁

kzfaq.info/get/bejne/gr-qmdylv9mse58.html nandito po sa isang video yung step by step po na guide 😊

I'm sorry I can't understand your language sir😔

@@boonbox12 he said "THE MOST IMPORTANT THINGS ARE NOT SAID"

Im sorry, the dialect is tagalog(filipino), will add some cc soon to make it more understandable 😊

@@boonbox12 I appreciate it 🤙🏾🤙🏾