Installing a TURBO on our BUDGET 50cc Drift Kart!

Рет қаралды 510,655

6 ай бұрын

We're on a side quest to bolt the worlds smallest turbo onto our 2 stroke 50cc budget drift kart build! Enjoy
Find the tiny turbo here - au.maxpeedingrods.com/product...
Use code 'Mikelake' for 10% off!
Raceworks goodness - raceworks.com.au
SP tools = the BEST tools - www.sptools.com/
➡️ Two Step Garage Store - twostepgarage.com/
➡️ DTAC Store: droptheanchorclothing.com.au/
➡️ Instagram @itsmikelake

Пікірлер: 480

@itsmikelake 25 күн бұрын

We're doing a 125cc TURBO swap! kzfaq.info/get/bejne/eNF4icSDqaulnI0.html

@rileywhittle1512 5 ай бұрын

The thrust bearing inside the turbo requires oil pressure to keep the impeller shaft floating in a film of oil otherwise it contacts and wears

@feelincrispy7053 5 ай бұрын

Depends if it’s ball bearing or bush

@aeroflopper 5 ай бұрын

@feelincrispy7053 both designs still need an oil feed

@itsbrendoni3444 5 ай бұрын

weld a nipple on the cap and pressurize it, remove cap for oil change

@BadHarmonics 5 ай бұрын

Journal bearing chra requires unimpeded flow, ball bearing NEEDS a restricted orifice ( on a car). This is almost certainly a journal bearing chra , and won't even spool correctly without proper flow / slight pressure inside the chra, and 270 thrust bearings( like this one probably): are even more dependent than a 360. Either way, the oil flow is also 1000% a necessity to not burn oil and coke up the bearing.... As all oil burns at turbo temps. The video guy is confusing the oil supply requirements as being similar to a roots blower. It's like building an engine without rings. You can do it, and it'll run. Maybe even for 30 whole minutes.

@ACplanet 2 ай бұрын

will filling it up to the near top thread, then screwing the bolt in, pressurize it?

@philliplock9249 5 ай бұрын

I agree the turbo placement looks awesome, but you'd probably find it more efficient bolting it to the intake. That'll give room for the expansion chamber, while offering instant response.

@itsmikelake 5 ай бұрын

I definitely agree with this, but it looks so damn cool 😅. We’ll re engineer some of the setup on the next vid and see how it goes 👌🏻

@Thumper68 5 ай бұрын

A small oil cooler etc used as an intercooler will help

@cxbra 5 ай бұрын

The turbo needs the exhaust for scavenging, then the compressor goes into the intake. If he didnt strap it to the exhaust, it might spin but wont make positive boost.

@Mrshotshell 2 ай бұрын

@@cxbra Pretty sure he meant to have the expansion chamber before the turbo

@itsmikelake 5 ай бұрын

I can't believe this actually WORKED?! 🤣Should we do a part 2 with boost gauge etc? We need to paint the frame too 🤔

@shaneanning180sx 5 ай бұрын

Yes part 2 please love the exhaust lol

@RAM_845 5 ай бұрын

Yes bruh! do both the paint and the boost gauge

@MaddyBoi_86 5 ай бұрын

Soo totally need to give it a bov ha ha. Love it ❤

@armandtventer8855 5 ай бұрын

Yes so keen for part 2!!!!!

@chickenwing071-6 5 ай бұрын

YEAH, I WISH I HAD ONE

@stuartwilson9064 5 ай бұрын

I used to get into 2 stroke rc cars, I would think a bigger expansion chamber would help. You could maybe loose the gasket under the cylinder to get a little more compression (use some goo instead and check the piston isn’t going to touch the top of the cylinder). Not sure how the clutch works in that thing, in the rc cars they were two half’s held by a spring. We would use a heavier spring so the clutch would engage at higher rpm’s. 🤷🏽‍♂️

@itsmikelake 5 ай бұрын

Amazing suggestions! Yep the clutch works the same as you’ve explained and I can in fact get heavier springs!

@wilsondriver654 5 ай бұрын

@@itsmikelakemight need lower gearing?

@Atris_965 3 ай бұрын

Hpi baja ..

@jamesgrech8295 3 ай бұрын

Put nitrous on it

@LokiMelb 5 ай бұрын

So good, I saw your thumbnail the other day, so Sunday morning got into the garage and finally welded my LCA to my 50cc drift quad. Still need supports and then chop the frame for the seat. But getting there. Love the tiny turbo!!

@waelal7484 5 ай бұрын

Every engine needs a expansion chamber tuned to its timing and rev range an displacement you can do your search.

@itsmikelake 5 ай бұрын

Thanks 😁🤙🏻

@Toxic2T 3 ай бұрын

truth. Once he learns its gonna be a drug to him. Each pipe has a diff result.

@minecraftblockychris8708 3 ай бұрын

its the other way around?

@cxbra 5 ай бұрын

A turbo 212cc 4 stroke would be even more insane! And tap a inlet and drain like that go to the bottom of the block in the oil "sump". Since 2 strokes dont have an oil sump, you couldnt get any heat relief from the hot oil inside the turbo. With. 4 stroke you would even be able to add an oil cooler in theory (which would cool the MOTOR down from the high pressure intake AND the turbo). Im surprised it worked using the same fueling as it did with n/a. Wow VERY cool many!!

@That1E_K1129 4 ай бұрын

Good job busting the myth of being able to turbo a 2 smoker. Me and my dad did it to a twin cylinder 440 jag smowmobile about 9yrs ago. It definitely works and definitely makes power! Awesome job man. New sub from me.

@itsmikelake 4 ай бұрын

Thanks bro! Yep, I’m the type of guy that just gives it a crack regardless of what the internet says haha. Turbo snowmobile would be so good 🤣

@That1E_K1129 4 ай бұрын

@@itsmikelake it was a for sure ripper man I wish I had video of it 🤣 thanks for replying my man! Keep killing i!

@user-ph2vp8uv1h 5 ай бұрын

Another killer vid mikey!! Cheers mate, looked super fun!

@itsmikelake 5 ай бұрын

Thank you bro! Fun little rig 😁

@user-hv6xy7jz9p 5 ай бұрын

Yes you can turbo 2 strokes.. I live in lake havasu city, az, USA and I've turbo charged so many 2 strikes even in the 125f degree weather and they love it. Remember to use a 2 cable throttle cable so it dosent run away from you

@itsmikelake 5 ай бұрын

This is what I like to hear!

@warmfreeze 5 ай бұрын

depends on the TYPE of 2 stroke your putting forced induction on.. but mostly your just blowing the fuel charge strait out of the exhaust..

@chrishenniker5944 5 ай бұрын

You can’t add forced induction to a two stroke, it’ll blow right through. A four stroke, they’re made for it.

@warmfreeze 5 ай бұрын

@@chrishenniker5944 again it depends on the TYPE of 2 stroke.. snowmobiles have an intake valve

@effigy42 5 ай бұрын

I worked on tiny 2 strokes for years just out of my garage and the biggest and best horsepower upgrades were aluminium motors with bigger carbis top speed 80km an hour with my worked 50cc iron and 95km with the 73cc iron but over 110kmph top speed with aluminium lighter has such a significant effect when so small

@itsmikelake 5 ай бұрын

That’s so fast 😅. I’ll do my best to get as higher top speed out of this one 😁

@effigy42 5 ай бұрын

@@itsmikelake good thing would be getting more traction for faster drifting then wouldn’t it

@chrisdocking9255 5 ай бұрын

Mike lake you savage! Look at how many like this video has!!! Bro I’ve been a sub since the bmw swapped, supercharged Corolla! You have grown my boy and my man I am so proud of you! Don’t stop baby don’t stop! Love from Nz

@rocketdragon4855 5 ай бұрын

If you'd want to make a 2 stroke exhaust that actually works well, you'd have to use a 2 stroke exhaust "tool"/calculator to get the correct measurements for the exhaust.

@itsmikelake 5 ай бұрын

I was looking at these online! We’ll upgrade the exhaust next vid 😁

@rocketdragon4855 5 ай бұрын

@@itsmikelake cool! I'm looking forward to it👍

@paolocane8875 5 ай бұрын

😂 that's the basic of 2 stroke engine! An expansion! But have to be specific misure!😅 That's not an expansion, that's a swollen pipe!😂 It looks amazing anyway!😎 Good luck!

@itsmikelake 5 ай бұрын

I’m learning as I go 🤣 but thanks for the advice!

@Teagan762 2 ай бұрын

Expansion chambers on 2 strokes can't just be guessed at. There as important as tuning a cars ECU. Length of pipe between the carb and chamber, Chamber to turbo and exit. Cool little build. I've built many.

@itsmikelake 2 ай бұрын

I’ve certainly learnt this with this build 😅. Cheers 👊🏻

@Turbowagon 5 ай бұрын

Very cool looking forward to future progress with this

@itsmikelake 5 ай бұрын

Cheers! Part 2 drops tomorrow 👊🏻

@Ismaak5 5 ай бұрын

You need an external oil system or the turbo won't last. I give it a couple of days before it lets go. There needs to be oil pressure in the bearings in order for the shaft to not come in contact with them. They need to float in oil not just sit in stagnant oil.

@itsmikelake 5 ай бұрын

Yeah that’s something I’m currently trying to sort out 🤔. I have a few ideas. I wanted to figure out if the 2 stroke would even accept boost first before sorting the oiling stuff 🤙🏻

@needmoreboost6369 5 ай бұрын

That’s correct under normal operating circumstances! but for this motor being suspended in oil with will work,And for a lot longer than you think! it’s submerged in oil! It’s not the same as in normal operation on a larger motor running out of oil!

@Ismaak5 5 ай бұрын

@@needmoreboost6369 apparently you are confused on how a journal bearing turbo works. Filling the cartridge with oil doesn't work. For starters the cartridge is not airtight there is a way for the oil to escape on both the compressor and the turbine housing. Secondary the oil needs to be pressurized or the bearings will come in contact with the turbine shaft. It is the same with any motor operating a turbo in fact in the case of a single cylinder engine it is even worse than a multicylinder engine due to pulsating waves of the exhaust pressure. Spinning the shaft at any speed will make it come in contact unless there is pressurized oil flowing through it for both lubrication and cooling. Especially with a small turbo that spools up quickly. The passages of the journal bearings are so small that without pressure essentially the spin of the shaft pushes the oil out of them.

@Madaz 5 ай бұрын

@@itsmikelake maybe an aquarium pump with an external oil resevoir

@rajgill7576 5 ай бұрын

@itsmikelake lol I get the sort one before you sort the other but trust, you want oil going to that turbo asap. I've broken a new turbo before by trying to sort out boost before lube. Not making that mistake again haha

@robertgillin 5 ай бұрын

you can definitely turbo a 2 stroke if your carb is a float bowl type you need to feed boost into the carb vent if its a diaphragm type its not necessary

@itsmikelake 5 ай бұрын

This is the EXACT type of info I’m looking for. Thank you 😁

@havegrinderwilltravel5 5 ай бұрын

Haha that's awesome love flutter ❤ good work mate that's what life about having fun just giving it a go 😎✌️

@itsmikelake 5 ай бұрын

Thank you my friend haha. Fun was certainly had!

@mopadrider6012 4 ай бұрын

This takes me back to the time i shaw a turbo gy6 scooter racing and winning against faster cars like whaaaat

@kanalagamer 5 ай бұрын

The homemade expansion chamber is not very good because the shape, curve, length and every other factor has to be considered for it to work. They are specially designed so that the exhaust gasses push any remaining fuel from the exhaust back into the cylinder. I suggest you get an expansion chamber of like a 50cc 2-stroke moped and use that. Expansion chambers can like triple the power output at high rpms.

@Bullwinkle39 5 ай бұрын

100% this. Every mini moto I've built for more power, the engine mods did virtually nothing but put a Leo Vince TT chamber on and the engines instantly come alive

@Toxic2T 3 ай бұрын

Indeed. 1/3 of the power comes from the pipe. The rest comes from compression, intake/carb and porting.

@Just-A-Guy-Learning 2 ай бұрын

Oil cooler, diesel fuel pump, very light weight oil, and oil catch can. Also a 12v source to power the fuel pump. Fill the catch can with oil. Bottom drain of catch can goes to fuel pump. Fuel pump, pumps the oil through the turbo. Drain of turbo runs to oil cooler inlet. Outlet of oil cooler goes to top port of catch can. Since you are adding a 12v source to power the fuel pump you can also add a small 12v oil cooler fan to the oil cooler.

@thatjdmkid8170 5 ай бұрын

I’m great at tuning those engines! I want to build one now

@777Spooky 5 ай бұрын

May God Bless And Be With You All Throughout Your Journey And All Throughout All Of Your Time Building Cars 💙

@frankz1125 4 ай бұрын

I build chainsaws and .020" squish is usually good to boost compression and port work. Nitros works as well. Cheers

@olivermain5078 5 ай бұрын

Cool dude this go kart rocks🤘

@IAM2CAN 2 ай бұрын

did you play around with the ignitiontiming and colder spark plugs?

@einhase6924 5 ай бұрын

If you really want to increase the power, you need to port it. Something like a wieder exhaust port and a higher exhaust Timings. Then you need a different expansion chamber. In general the champer should be shorter, but it must be tuned for your setup. You can also bore out the carburator or get a bigger one.

@Toxic2T 3 ай бұрын

This, no need for turbo. Just porting, better reeds, bigger carb with proper intake tube and a custom pipe will do the trick.

@TURBOTRISTO 5 ай бұрын

SOUNDS GREAT

@itsmikelake 5 ай бұрын

Knew you'd love this one Tristan! Haha

@MicahBell_1860 5 ай бұрын

Happy trails, Cowpoke

@itsmikelake 5 ай бұрын

🤣🤣

@jake3085 5 ай бұрын

Cheers for dropping this on my birthday 👌 few ideas, put a dose pipe on the intake of the turbo, fiddle around with the length and maybe we can hear some vl turbo dose noises coming outa this thing Also, see of you can hook up a wideband to this thing, its probably leaning out as I imagine the boost will push the fuel out of the carb, maybe add a vacuum line from the charge pipe to the fuel tank so that there is no pressure differential in the carb Make a new dump pipe where it separates the wastegate opening then have a muffler and a screamer pipe Im half tempted to go buy a little pocket rocket and try this stuff now 😂

@itsmikelake 5 ай бұрын

Happy birthday my bro! Haha crazy that everything you’ve suggested is exactly what I have planned 🤣🤙🏻

@jake3085 5 ай бұрын

@@itsmikelake cheers bro! Great minds think alike hahaha

@Fk8td 2 ай бұрын

Larger expansion chamber on the exhaust should help it rev a bit more because total exhaust volume will be larger allowing more total exhaust out but at sacrifice of lower rpm and mid range power

@user-qz6mr9iv4e 5 ай бұрын

Well done lad

@InternetGangster420 5 ай бұрын

STUUTUUSTUUSTUU!🔥

@themartian1148 5 ай бұрын

i made a small turbo for a rc car and they run like a 2stroke and it worked i was supprised because alot people say you cant turbo them but it seem that you can

@jmrides777 5 ай бұрын

Great job bud...sheesh I had just as much fun watching this vid as you did building it. Where did you get the mini turbo from? I wanna put one on my kit bike.

@itsmikelake 5 ай бұрын

Thanks! So glad you enjoyed it. Link is in the description for the turbo 😁

@robivlahov 5 ай бұрын

build an airbox that houses the whole carb, and boost into the airbox, you are having trouble with the pressure differance as its not a blow trough carb. pull the piston out cut it up to remove the piston port and make it reed induction, so that the turbo has more time to fill up the cranckase and cylinder.

@Clippy_1 5 ай бұрын

You can probably make even more power if you use a real two stroke exhaust pipe from a moped. If you want to make it faster and I would recommend to engine swap it with a Yamaha yz 80 or Honda cr 80 engine and make a shifter drift kart.🤔 Very cool project!

@itsmikelake 5 ай бұрын

Part 2 is LIVE here! kzfaq.info/get/bejne/r-BlptejsdWwZ4k.htmlsi=IQ3l11eAPhsYyCTL

@user-fc1zs1wh9g Ай бұрын

not the the worlds smallest turbo

@Bimmerfan7849 5 ай бұрын

Epic mate 🤙

@itsmikelake 5 ай бұрын

Thank you bro 😀

@Ingo3112 5 ай бұрын

did you add the boost sound to the video or make it realy the sound ?

@lincolnking9039 5 ай бұрын

Hey Mike u will have to change the needle position too to get some more fuel in will run better too since u turboed a 4 wheeler

@scottybutterworth666 5 ай бұрын

Thats wicked you've inspired me!

@itsmikelake 5 ай бұрын

Cheers Scotty. Bloody good fun!

@Donvito-vk8vq 5 ай бұрын

He did to me to I’m looking for one to build up now

@steelearmstrong9616 5 ай бұрын

That turbo on there looks awesome

@itsmikelake 5 ай бұрын

Cheers!

@diyathomevn 5 ай бұрын

a new car. turbocharged motorcycles. I agree that the turbo placement looks great, but you'll probably find it more effective to mount it to the intake. The turbo needs oil pressure to keep the impeller shaft floating in the oil film, otherwise it will become exposed and worn.

@fabio77809 5 ай бұрын

Hi Mike, thanks for posting this video

@itsmikelake 5 ай бұрын

You are very welcome

@fabio77809 5 ай бұрын

@@itsmikelake A thousand thanks

@thatjdmkid8170 5 ай бұрын

I’m bout to pick up the same quad just because of this

@rishujatav5585 5 ай бұрын

OP modification bro 👍💪🥶

@itsmikelake 5 ай бұрын

Thanks!

@chug_n_toke8849 5 ай бұрын

That's so awesome!!

@itsmikelake 5 ай бұрын

Thanks!

@420AuFalcon 5 ай бұрын

Cheers Mike ,, I reckon throw the other carby on the front of the turbo, , twin carb turbo drift cart🏎💨💨💨

@mick00000000002 5 ай бұрын

Could you put a oil system of the crank. Tank radiator and pump of the shaft. To cool down the turbo? More guys. Please. Thank you. Do the Max. Think out of the box guys. ❤

@grimairbrush 5 ай бұрын

hey mike, the turbo flutter on the 2stroke was pretty awesome lol

@itsmikelake 5 ай бұрын

Thanks bro. So cool hey 🤣

@Altie8 5 ай бұрын

thats insane

@JoshPhoenix11 2 ай бұрын

Can you use reed valves on the intake with a turbo? Also you might want to run it slightly on the rich side so it keeps the engine cooler

@seanluna5956 3 ай бұрын

ive wanted to throw a turbo on my 2 stroke jet ski this gives me hope it might work

@SkyfighterZX 5 ай бұрын

Next video: "We slap a turbo on a ROCKET SHIP" 😂😂 Also i absolutly love that tiny air filter, adorable

@glock19cgen5 5 ай бұрын

you earned a sub from me dude I need a turbo go kart to get around on

@itsmikelake 5 ай бұрын

Appreciate that homie! I think everyone needs one of these bad boys 🤣

@Scxjunkie 5 ай бұрын

The little waste gate sound is much needed

@paydroku 5 ай бұрын

The world's cutest turbo 😂its a key chain bro

@itsmikelake 5 ай бұрын

Haha exactly right 🤣

@markkmchugh 2 ай бұрын

Nice work. Your not a nob either which is great :) New subscriber.

@hopdjandy 5 ай бұрын

Love the sound of it dumping

@itsmikelake 5 ай бұрын

Same 😍

@mechanicfromeurope 2 ай бұрын

It sounded like it was edited in

@bosscalam4463 Ай бұрын

i need to buy a mini turbo for my kart too

@aaronjnrnichols4642 5 ай бұрын

lets go mate u told me it would be here today thanks for being honest. great Vid

@itsmikelake 5 ай бұрын

Thank you bro! Doing my best to pump out quality content haha. Cheers

@aaronjnrnichols4642 5 ай бұрын

You should do a meet and great next weekend while im down there.@@itsmikelake

@anubisblack521 5 ай бұрын

you should have a carbon seal installed in the turbocharger for a draw through carburetor system ideally!

@itsmikelake 5 ай бұрын

This would certainly be the ideal setup!

@mattdaniels2798 5 ай бұрын

If you think that's sketchy try doing the down hill drift trike on Okemo mountain! VT💪🏻

@itsmikelake 5 ай бұрын

Haha yep, that's sketchy asf!

@descent8275 5 ай бұрын

hey my dude, won't the boost push the fuel back into the fueltank, since a carb works with the venturi effect, what builds a slight vacuum to pull the fuel into the carb?

@itsmikelake 5 ай бұрын

I have a boost line running to the fuel tank which seems to be working at this stage 🤔

@captcade2913 5 ай бұрын

You should make coloured smoke on the wheels, that would be sick

@someweeb3650 5 ай бұрын

I wanna see 2 of these on a little 4 cylinder

@CamdenIglehart 3 ай бұрын

might wanna add an airfilter to the front of your turbo so you dont dust your engine!

@domcxz8643 5 ай бұрын

THIS IS SO COOOOOL :)

@itsmikelake 5 ай бұрын

Thanks!

@f.450d.c6 5 ай бұрын

Hey brother, the only thing I would say is it’s a beautiful thing I would do is one I’ll get a different engine and make it a little bit more powerful I understand you like tiny motors. It’s really efficient and everything else but you’re doing the turbo outside, throw much bigger engine on it For stroke 110 engine so you can get rid of toppers and probably make something a lot better but you do have to worry about the field mixture and everything else then but if you need some help with that. Just talk to me.

@smoothwalrus9354 5 ай бұрын

So good!

@itsmikelake 5 ай бұрын

Cheers!

@icanseeyouallfromuphere 5 ай бұрын

Next you need to manufacture for sales 😂

@itsmikelake 5 ай бұрын

👀 imagine haha

@icanseeyouallfromuphere 5 ай бұрын

@@itsmikelake class bro ! ✌🏻

@BoberSmink64 5 ай бұрын

put some normal tyres on it and do a max speed test with and without the turbo to see the power gain

@itsmikelake 5 ай бұрын

Deal! I’ll use mobile gps to track speed 👊🏻

@discipleoftheword1785 5 ай бұрын

100% passion projects are so much more interesting to watch. Kind of feels like I’m a part of it.

@itsmikelake 5 ай бұрын

Absolutely agree! Thanks for watching 😁. Part 2 coming next week 👊🏻

@ericmuhlbeier8023 5 ай бұрын

They do turbo 2 strokes.. for snowmobiles.. I suggest u build an oil system for iT with a pump or the turbo won't last

@itsmikelake 5 ай бұрын

We’ll keep upgrading it as we go 😁

@collinkaufman2316 2 ай бұрын

Will a compound turbo improve performance?

@doridex 5 ай бұрын

Lol this is so much like my budget drift kart! Same base quad too lol. Ive just swapped a gx200 clone motor. 100$ for 6,5hp

@Justin-DA-Monkey 5 ай бұрын

u should get one of those scooping filers for the turbo and maybe make a better expansion exhaust and intake or probably upgrade the engine like a big bore kit or sum for the turbo to work better cuz i lowkey wanna see the limits of that engine

@Justin-DA-Monkey 5 ай бұрын

and if u need a pump for the turbo just make a mechanical pump thats connected to the engine so it would be like a supercharger but a pump and make sure to gear it down too cuz its just a lil pump

@itsmikelake 5 ай бұрын

I agree with you bro, I’d like to see the limits of this motor also! We’ll be making upgrades, don’t you worry 😁

@dirtbikeboy8794 5 ай бұрын

Does it feal faster? I am just wondering for a vary simular project.

@itsmikelake 5 ай бұрын

Absolutely feels faster. Once we dial on the fuel and expansion chamber it should be even better!

@persvang90 2 ай бұрын

12V oilpump with a tiny oil cooler should work great

@_CryptoNoob_ 2 ай бұрын

Making a small oil tank would have way too much work eh? Lol

@RollinMyOwn 5 ай бұрын

You should talk with 2strokestuffing....he is nothing short of genius about 2 stroke motos...

@randywhite7434 5 ай бұрын

If you can somehow make a smaller exhaust straight pipe it may create more compression I did it to my Yamaha banshee it added compression and sounds good

@user-hz7ku6ji3o 5 ай бұрын

i wonder if u could put either daul motor or super charger

@ManiacRacing 5 ай бұрын

How does that carb not spew fuel everywhere when the bowl gets pressurized under boost? My understanding is that carb turbo applications need a sealed carb and boost referenced float bowl and/or fuel pressure to contain the boost so it doesn't simply blow the fuel back through the jets into the bowl, which is vented to atmosphere. The only thing I can think is it's simply not even making enough boost to cause fuel problems, which means not much at all considering how little the carb is....any thoughts?

@joshydoy 5 ай бұрын

you should get the 19mm carb with the uprated intake for this so the carb isnt a huge restriction

@buildaboiworkshop 5 ай бұрын

Maybe even 21, unless you want speed then you can go up to 32mm; but it won't be good for much beyond full throttle all the time

@craigbaker1071 5 ай бұрын

Slap a BOV on it!!😂

@user-cm4sq2lz6f 5 ай бұрын

You should take the covers off the back tires and record a top speed run

@christopheramoroso6801 2 ай бұрын

Look at snowmobiles ya there's Turbo Kit's we put on 2strokes

@woihoi4901 2 ай бұрын

Drift kart ❌ Mosquito fogging machine ✔️

@GregCo 4 ай бұрын

¿Que turbo es ese? Por favor el link de compra 🛒!

@bryannakvinda8411 3 ай бұрын

Why not get a pump and tank for oiling the turbo not a hard system to build fyi best to put carb behind turbo and using starter fluid to bump it off on first start

@Abhishek_Ranidu 5 ай бұрын

Awesome 😮❤🫡

@itsmikelake 5 ай бұрын

Cheers!

@blizteredthumbs7911 5 ай бұрын

Not a turbo drift kart, it's a tirbo drift kart. 🤘

@hughstonfeg9872 4 ай бұрын

How dose it sputter how did you get it to do that

@chadcramer4024 5 ай бұрын

My chevy cruze 1.4t 2016 has a 31mm opening on the intake of my turbo, stock

@jamescollins4833 5 ай бұрын

Have thought about a small oil cooler on the turbo and I've been trying to find someone to help me build a sleeper to take on a favorite vehicle of everyone