Transforming a KIDS QUAD into a 125cc Drift Kart (START TO FINISH)

Рет қаралды 163,866

Күн бұрын

This is the complete build, start to finish converting our 50cc kids quad bike into a monster 125cc budget drift kart! Enjoy
Raceworks goodness - raceworks.com.au
SP tools = the BEST tools - www.sptools.com/
➡️ Two Step Garage Store - twostepgarage.com/
➡️ Instagram @itsmikelake
➡️ DTAC Store: droptheanchorclothing.com.au/

Пікірлер: 144

@itsmikelake 28 күн бұрын

We're doing a 125cc TURBO swap! kzfaq.info/get/bejne/eNF4icSDqaulnI0.html

@itsmikelake 4 ай бұрын

I've ordered the TURBO kit for this kart! Until then, grab yourself a cup of coffee & enjoy the complete 125cc build start to finish ❤

@kriswhite9324 4 ай бұрын

Was about to say that in caps lock with my keyboard so glad your turbo'ing this lil monster of a unit 🤙🤙

@brianmosleyb9104 4 ай бұрын

Hey Mike! I wanna give you a huge tip on the clutch to make the kart lest cluttered and easier to drive. Put a brake lever on the shifter arm and run the clutch cable to that. That way your only thinking about your shifting arm and can keep your feet planted on the footpads! Awesome build otherwise bro! I wouldn't have don't anything different besides that

@brianmosleyb9104 4 ай бұрын

Less*

@kevinclear4007 4 ай бұрын

Turbo kit? Link?

@R.A.W.R.NEWS.T.V.1776 4 ай бұрын

Hey Bubba I'm not like a professional designer or Builder but I want you to step back and take a look at the car and look from your steering point to back behind by the seat. You need some kind of reinforcement between the steering column and the seat running between the steering bar of course and your seat mounts because you will get downward and upward Flex and you will get twisting of the cart because of all the torque on that little Kart frame. You could even go as far as to welding studs Under the Seat bracket on the downside and weld studs near the steering column and then you can make two pieces of pipe flattening the ends and drilling holes putting them on after you get the motor back in it you can just put a washer in a lock nut and basically give yourself rigidity structurally on both sides of the motor at the top end of the frame so you don't get bending and twisting. But you can undo the lock washers add nuts when you have to remove the motor for servicing. Also that top rail mount would work good for a turbo Mount being that your exhaust manifold is right there at the top of the motor you can probably incorporate some type of tubing to the front of the frame of the cart and even take a small radiator of some type to make you an intercooler put a set of small computer fans on it. But yeah man that's what I would do I would definitely take two bolts and weld one underneath each side of the frame mount for the seat and put one on either side of the bar at the front near the steering column and make you two structural bars that go across the top that can be REMOVED for servicing. All in all this is a sweet little bill I wish I could build something like this

@Erle_The_Pearl 2 ай бұрын

Sorry to see this, Glad you’re okay and you can always rebuild. Loved watching the progress

@user-np4zt2bl5j 4 ай бұрын

Perfect video to watch on a night of not being able to sleep

@itsmikelake 4 ай бұрын

Glad I could entertain you during your insomnia 🥰

@user-np4zt2bl5j 4 ай бұрын

@@itsmikelake you're awesome and i hope everything is going good in your life.

@CygnusHomes Ай бұрын

Dude the adhd, the absolute joy in jumping into the unknown. We are twins! I'm building a tiny imported reverse trike and turboing as well check my build out! Cheers

@brendanwebb9840 3 ай бұрын

This is awesome. Definitely inspired to get tinkering

@baeiv1048 4 ай бұрын

Been waiting for this man love to see it, keep it up i think everyone has been enjoying this series!!

@Twiggsz 4 ай бұрын

Been loving the series man can’t wait for the future episodes.😁

@murk1352 2 ай бұрын

That thing is friggin cool! You gotta get you hands on a KX80 2stroke engine or a CR125 Honda 2Stroke engine & install one of them & then you’ll really be loving that little kart……✌🏻🔥🏁

@Thegreatabissofhell666 2 ай бұрын

i love the mad max vibe of the drift cart next you should try putting a supercharger on it

@haydensmith6809 4 ай бұрын

For everyone watching, gas & clutch pedals I made home made ones on my first build which were good but time consuming, next build iv used cable brake levers from a bmx and welded abit of handlebar to the frame to mount! Super simple 😁

@S3brandon Ай бұрын

Could you make the frame longer? I think it would be more comfortable to drive

@PatonMachines 4 ай бұрын

Enjoying your videos! Mikemas got me hooked! I have a little build coming up with my sachs rotary. Just have to finish my oil drum mini ute first!

@itsmikelake 3 ай бұрын

Thank you bro! I need to do a Sachs rotary!

@TJAMES747 2 ай бұрын

i run the same welder, my uncle who is a certified boiler maker recommended it to me to start out ages ago and I'm still using it, mint little unit.

@Altie8 4 ай бұрын

ive been waiting for this moment to come yes i love engines tbh

@TheCybrKnyf 2 ай бұрын

Well done on the entire job - Smiles for miles. Set yourself a task and crushed it!!! Well farking done!!!

@TheCybrKnyf 2 ай бұрын

You will also need to mount the foot platforms ABOVE the bottom frame rail - or at the very least even with it. Below as it is now will cause dragging constantly.

@BenHut69 4 ай бұрын

I wonder if it would be possible to adjust the steering ratio so you have more control in drift. It seems a bit touchy, might help quite a lot tho. Thank you for the long video Mike! Love this cart so much

@itsmikelake 3 ай бұрын

We can definitely mod the steering to make it easier to drift. I'll fiddle around with it a bit in a future vid :)

@rinkinkel 2 ай бұрын

If you don't have a proper pipe bender, what you can do is stuff the pipe full of sand and close the ends with a weld or wood or whatever. That will make the bends look a lot better, specially if you heat it up a bit. After you're done, just let the sand drain out.

@skyfreakwi 2 ай бұрын

Can't wait to see how this goes. Personally I would be going there opposite in most regards. Maintain the rear swingarm and suspension. And put all the weight forward. You gotta think front weight rear spin and slide rear weight means it'll hook like nothing else. You did say drift cart not wheelie cart. I gotta be concerned that this will flip easily and often. We'll see, prove me wrong. Regardless it looks fun as hell!

@user-de7qh4hs2m 2 ай бұрын

Put wheelie bars on it. With a set of roller blade wheels on them. Before you bust the seat back rest.

@mcanderson0 2 ай бұрын

bro put kinked tube in place when you can just weld multiple straight pieces together to accomplish the curve? Imagine pie-cuts on an exhaust... but just 3 or 4 'pie cuts' to make a choppy curve. IDK if that makes sense but you dont have to bend pipe to accomplish this task, just use multiple angles to make the shape

@chuckkeeler1112 2 ай бұрын

you could cover the x braces with expanded metal still see the x braces but will make it much stronger

@Scottwillow1 2 ай бұрын

Battery needs a bar to protect it

@JokerInk-CustomBuilds 3 ай бұрын

honestly I'd put a wheeliebar on it... Watching the testrun was nailbitingly fun! :D Great work and great video! -Don't end yourselves! :D

@itsmikelake 3 ай бұрын

Haha absolutely agree, wheelie bar incoming!

@Thatfordguy1973 4 ай бұрын

That’s ke70 in the background is sick

@cottontop2756 3 ай бұрын

that thing looks like so much fun

@itsmikelake 3 ай бұрын

The smiles per dollar are well high!

@user-ds6ur2og5p 2 ай бұрын

Welding over paint? No metal prep before welding? Even made emt conduit pipe look at strong and sturdy. That welding machine is worth every penny!!!

@matthewharsaghy6555 4 ай бұрын

Once that motor blows put a cr85 in it cmonnn, 2stroke gang😂💪

@chuckkeeler1112 2 ай бұрын

put a triangle gusset on the outside of your bent pipe on each side

@gordonpotter3943 3 ай бұрын

Hi Mike.. hey the kart rims you got do you have any info on the sizes and if they were front or rear rims. Thanks mate…

@vxrlorxnxrreal 4 ай бұрын

this serires was so fun to watch!

@itsmikelake 4 ай бұрын

More coming soon! 😁

@user-jh8jh9up3v 3 ай бұрын

Before you put your plate in across the bottom of the frame under the motor think about oil changes. You know so that way you don't have to pull your motor to get the oil out of it

@Tyresong 4 ай бұрын

Now for a drift Mobility scooter? I have a 6.5hp stationary engine that is worked to 16hp on my go-kart that I crashed and messed up the font end. I'm really tempted to put the engine on a tiny little kids Minibike... but that just wouldn't be safe. I would have to extend the rear end, put some longer risers on the handlebars, and upgrade the rear brakes as well as fit front brakes.

@sondrenymark6916 3 ай бұрын

you should change the seating position, that will destroy your back if u hit something hard or a bumb in the road, and if you have time add a handbrake as back brake and a own frot break for stops

@user-jh8jh9up3v 3 ай бұрын

Okay if you have to go over a speed bump you're going to be high sided but the profile look sweet

@NoSubGAMMIG2144 3 ай бұрын

Yeah, dude, that's sick. Work smarter, not harder. 🎉 😊 🎉

@Gold469 2 ай бұрын

Put some wheelie bars on that thing... ride till the wheels come down.

@rogertrip74 4 ай бұрын

Fill the tubes with sand tape the ends and they won't kink when you bend it with out the correct die size

@ChristopherAdams-tl3me 3 ай бұрын

Why didn't you use solid round bar for the base so that the waight is low in the frame

@spookypoopy6036 4 ай бұрын

Hey I’ve been watching this series for a while and I’m building something similar, I’m also starting with the quad bike frame but I want to build it for speed and aesthetics rather than drift I was wondering where I can get tiny turbos like the kind on your old 50cc engine. I understand that you were gifted it from a friend (as you said in an older video), but are these commercially available anywhere? I haven’t seen them yet. Would I have to design one myself and get it cnc milled?

@itsmikelake 3 ай бұрын

au.maxpeedingrods.com/product/high-performance-rhb31-vz21-mini-turbo-small-engine-quads-rhino-motorcycle-turbocharger.html :)

@spookypoopy6036 3 ай бұрын

Cheers, that’s a little out of my budget though :/ I love the skyline btw

@cuberznl 3 ай бұрын

turbo and 2 stroke dont go well together :) the exhaust and intake are open at the same time so a turbo wouldnt do much for actually getting more in the engine cuz you cant hold the boost pressure

@MrMecano 3 ай бұрын

Check on the jetting or at least adjust air screw because thoses backfire are sign that it's running lean and that's no good!

@vegaskidgsxr600 3 ай бұрын

If you don’t have a bender and want a nicer looking pipe you can fill the pipe with sand cap the end best if you weld something on the ends then bend it make sure it’s full the the brim

@glennnikkelson1140 4 ай бұрын

Now you need to cut them bars off on the front and order some mini coilovers for the front

@michealdebono4432 4 ай бұрын

That thing is sick you should put push bike handle bars with a thumb eccelerator from a quad bike

@User62719 17 күн бұрын

Where did you get the motor from

@hatton992 4 ай бұрын

Arh good old kart such a good build

@itsmikelake 4 ай бұрын

Just wait till we take it to the next level 😈

@watahyahknow 4 ай бұрын

there quite a few things i wouldve done differently first of all fill the pipe with sand or with water and freese them solid before bending them , they whont kink when you do that , is harder to bend though i wouldve mounted the rear bearings upside down so the bars wouldve gone under the axle , this wouldve given you an (allmost?) straight shot intoo the bottom part of the frame and wouldve done away with at least on bend , wouldve meant changing the bracket for the diskbrake caliper around a little as that hangs under the frame too (likely cut the bracket loos and mount it vertical in the front of the disk wouldve made the part strengthening the steering part and bottom piece out of one bar mak ing a 45 degree bend and weld it at the top and in the bend at the bottom using a plate likely only need a crossbrace under the seat as long as the chain can pass through the plate holding the engine in should prevent the bottom tubes from moving

@copiertech101 2 ай бұрын

Maybe you should make a video

@sebby_cnc 2 ай бұрын

how about using a pipebender so you dont have those kinks init makes it more strong aswell

@xMLRxDaFupa 2 ай бұрын

its like a honda grom in a cart

@UnRated314 3 ай бұрын

Bro definitely keep the frame exposed double x life

@User62719 17 күн бұрын

Where did you get the frame from

@Sicwhipz 3 ай бұрын

Where did you buy the motor

@michaelkolosey5756 3 ай бұрын

Why not straighten up that front steering so that the front tires are straight?

@hectorjauregui3404 3 ай бұрын

you should put 2 skate board tiny wheels on the back so when you do wheles don't go up

@itsmikelake 3 ай бұрын

Wheelie bar install?!

@treya2403 2 ай бұрын

It needs stretched about 3ft and it would be way more fun way more controllable

@rinkinkel 2 ай бұрын

After about 25 minutes, my tows are sufficiently curled.

@NoSubGAMMIG2144 3 ай бұрын

You can buy a link extractor very cheapl and it works much more efficiently. There is no😢 risk of damage or hoop loss. ❤

@robsmall5155 3 ай бұрын

The Ship Of Theseus Kart lol

@Bob39965 4 ай бұрын

You should have put the shift on the steering wheel and put a hand brake on it?

@roypatterson9910 3 ай бұрын

You should have added a finger lever throttle to the steering wheel.

@Ofca_PL 2 ай бұрын

Wicked

@roypatterson9910 3 ай бұрын

You should have lengthend the frame by 6 inches.

@Milk-lm7zy 3 ай бұрын

If you really want to get some power out of a 2-stroke adding boost will do pretty much nothing since it doesn't have valves and the exhaust will always be open too while the intake is open. Instead you could add a proper expansion chamber to help with scavenging, there are plenty of tutorials online on how to do this and with a properly designed one you can gain between 10% and 40% more power.

@itsmikelake 3 ай бұрын

The boost worked well! The expansion tank would help for sure also

@Milk-lm7zy 3 ай бұрын

@@itsmikelake Then maybe the exhaust restriction from the turbine was enough to build some boost pressure. I personally didn't have so much luck with turbocharging 2 strokes. If you really want to build more boost you could maybe add rotary valves or similar to the exhaust, although that would be a lot of work. Anyways, It's really cool to see some actual Turbo 2-strokes working. Good luck with the project

@C_Stylezzz 3 ай бұрын

Oh jeez thanks dude idk why u all are hating it's really a working update that can really be done you just have to have a very specific ps3 and it's only the models that slide open but certain one hell I'll even give to secret it was the first 15000 units that were scattered through us states only so if your sn has 15k or below yoy can do this really but there is another thibg he isnt showing tho

@michealwardle6526 Ай бұрын

Why not a 3 speed centrifugal with reverse motor heaps more fun for drifting

@itsmikelake Ай бұрын

I just really like being able to shift through gears 😁

@deeblood438 3 ай бұрын

Should add weights to front end

@loganhenry3322 3 ай бұрын

Need to take some skateboard wheels and make a wheelie bar

@itsmikelake 3 ай бұрын

Wheelie bar video coming real soon 😁👀

@loganhenry3322 3 ай бұрын

Just thought it might help with taking off quicker Shout me out in your next video

@CostaONEsixONE 4 ай бұрын

The durability and stability of kinked tubing. 😂😂😂

@itsmikelake 4 ай бұрын

Still works mint 🤷🏻‍♂️ don’t hate the player haha

@CostaONEsixONE 3 ай бұрын

I did work.. I’ll give ya that one..

@user-le9dh7if3b 2 ай бұрын

broo you earn my subscribe

@itsmikelake 2 ай бұрын

Thank you bro 👊🏻

@chuckkeeler1112 2 ай бұрын

leftover wires probably lights

@Cbt_boys_on_125s 4 ай бұрын

Is that a Datsun 240/260z 🤤

@itsmikelake 4 ай бұрын

280 😛. Dropping a new video on it tomorrow!

@ChristopherAdams-tl3me 3 ай бұрын

If you leave it open it will be able to run coller

@nemo500 Ай бұрын

i have the same engine on my atv

@dxjxrose 2 ай бұрын

fill the tube with sand next time before ghetto bending and it wont kink

@T-HobbiesG45 2 ай бұрын

Put the turbo back on

@bencrosbie6003 4 ай бұрын

Yeewww! 😎✌️

@itsmikelake 4 ай бұрын

😁👊🏻

@itsmikelake 3 ай бұрын

My latest vid is here! kzfaq.info/get/bejne/rsmqfsSim-DNinU.html 😁

@wyelandlebeouf7202 2 ай бұрын

Lol mine is probably much lighter with 212cc😂😅

@MrAntett 2 ай бұрын

imagine putting on a lonicin 250cc lmao :D

@adamorsini4585 3 ай бұрын

You just created a major failure point in the frame with those kinks in the tubing. Bracing it ain't gonna do jack.

@itsmikelake 3 ай бұрын

Nah, she holds together great! We’ve thrashed the heck out of it and no problems at all 👊🏻

@adamorsini4585 3 ай бұрын

@@itsmikelake over time that spot will probably develop a crack.

@establisha 3 ай бұрын

using kinked pipes for frames gotta be a new thing

@itsmikelake 3 ай бұрын

Nah nah it’s been around for ages 🤣

@midunk5811 3 ай бұрын

Im from indonesia we use that engine on motorcyle so please put turbo on that engine so maybe i will make my motorsicle use turbo😂

@briancovington5870 Ай бұрын

Due to the fact it was pink it sounds like a bubble mower I would name it the bubble gum mower

@auscarphotography 4 ай бұрын

My go kart motor is the same brand

@itsmikelake 4 ай бұрын

They go harrrdddd 👀

@user-de7qh4hs2m 2 ай бұрын

Don't ever run a small moter with out an exoust. You will burn a valve.

@Nash12372pash 4 ай бұрын

How is it possible

@itsmikelake 4 ай бұрын

Hard work and determination 😛

@user-lu2zg2hz2l 3 ай бұрын

Sup bro i think you should make a car like body for the go kart give a supra skyline any car body sorry if bothered you annoyed you bye have a nice day

@JelatoAkitas 4 ай бұрын

Me:dude ur wife just filed for divorce Him: nothing a little wire brush cant fix

@itsmikelake 4 ай бұрын

🤣 hahahaha

@patrickbuddenhagen5607 2 ай бұрын

You Might Want To Add A Heat Shield Of Some Sort, might scorch your nuts or legs in the engine

@itsmikelake 2 ай бұрын

You’re not wrong about this 😅🤣

@Dogman21 2 ай бұрын

MOTOR= electric ENGINE combustion!!

@WilliamMcPherson-qz9qx 4 ай бұрын

First

@TheCybrKnyf 2 ай бұрын

Sheet metal would look better, but you are running an air cooled engine. Leave it exposed...

@2dog_bronco_livin768 3 ай бұрын

News flash, that frame does NOT look awesome with the kinks in the bends

@itsmikelake 3 ай бұрын

Looks rad all braced and painted! And has performed flawlessly thus far 😁. I’m always learning, next will be better 👊🏻

@jamesthebond0072 3 ай бұрын

You do realise it’s got a clutch for a reason it’s supposed to be used you’ve probably already ruined the motor

@TalibandzFromDaBz 3 ай бұрын

He’s using the clutch

@k4fbrandon147 3 ай бұрын

Get a weelie. Bar😭 and do weelies

@itsmikelake 3 ай бұрын

That’s the next video coming 😛😁

@user-jh8jh9up3v 3 ай бұрын

Okay if you have to go over a speed bump you're going to be high sided but the profile look sweet

@Sicwhipz 3 ай бұрын

Where did you buy the motor