@TheBTRGarage Жыл бұрын
*Install the lip nuts and bolts opposite of how I did to avoid cutting bumper support plastic!* (nuts on the outside)
@iRAGEeveryWEEKEND Жыл бұрын
Great install! I mounted the bolts opposite of the video and used a 7/32 drill bit to make it easier to push the bolt from the inside of the bumper. The washers didn’t fit under the front three mounting holes because they were too close to the curve of the lip on mine and I believe the newer version have 3M in the center too.
@TheBTRGarage Жыл бұрын
Thanks, and appreciate the feedback!
@patrikcent1 3 ай бұрын
Good tip! Wouldn’t the bolts stick out too much over the lip/bumper to the ground though?
@nicklauher9323 Жыл бұрын
Got this lip last week and will install this weekend. Thanks so much for the play by play BRT Justin
@TheBTRGarage Жыл бұрын
Awesome! Install the nuts and bolts opposite of what I did and you can avoid cutting the plastic bumper support!
@Fuddermucker47 10 ай бұрын
Going to be installing one of these today on my car and I’m a bit nervous but this video is super helpful. Really appreciate the tip to put the bolts/nuts the opposite way!
@redkatana7450 4 ай бұрын
Your video helped a lot in my installation of Aeroflow lip. Thanks!
@miguelm3676 2 ай бұрын
At 140 miles per hour mine exactly after following your video came off in one side and tremendous feeling when I hear the flapping noise.
@artblackwood7936 Жыл бұрын
You have a nice balance of bling and performance. Cool.
@TheBTRGarage Жыл бұрын
Thanks!
@forlier5325 Жыл бұрын
looks good! the 86 is really coming together 🔥
@TheBTRGarage Жыл бұрын
Thanks! Got a few more upgrades in the plans :)
@NoHoHank 9 ай бұрын
Very nice lip!! This should go well with a Racebred front splitter
@sikrip Жыл бұрын
Nice job!
@TheBTRGarage Жыл бұрын
Thanks!
@GP-fc7jv Жыл бұрын
Looks great are you going to put on a splitter
@TheBTRGarage Жыл бұрын
Not planning on one anytime soon.
@rhkean Жыл бұрын
That looks amazing!!! I have some questions... 1. The 2 extra clips... I couldn't tell... Are the new bolts holding the shields in correctly now? Ie. Did the bolts completely replace those clips? 2. Would shorter bolts prevent the need to cut the bumper piece? Those bolts looked much longer than needed.
@TheBTRGarage Жыл бұрын
Yes, the bolts replaced the 2 clips and it is even more secure with the bolts. Shorter bolts would help, the provided ones were indeed way long. I still think you'd have to trim a little bit of that bumper plastic shroud, because it butts up against the nuts/bolt ends.
@rhkean Жыл бұрын
@@TheBTRGarage thanks! It's back ordered 😭😭😭
@rhkean Жыл бұрын
I mean... Not that I IMMEDIATELY went to order it or anything... 🤣
@rhkean Жыл бұрын
My 19yo, who is sometimes more practical than I expect (for being 19), asked, "but why" I said, "bumper condom... All your scuffs will go to the lip, and for $225, it's easily replaceable... Plus, it looks amazing" 🤣
@TheBTRGarage Жыл бұрын
@@rhkean 😆 well that's a bummer it's backordered already.
@zenkijoe9022 2 ай бұрын
What size tire were you running here?
@zenkijoe9022 2 ай бұрын
And were you on spacers? Any rubbing with the springs?
@TheBTRGarage 2 ай бұрын
@@zenkijoe9022 those are the GT Radial 235/45/18's. 12mm spacers all around, no rubbing, but I also have shaved fenders.