In this video we convert the Golden Jubilee from points type ignition to Pertronix electronic ignition.
Пікірлер: 37
@davidbunnell756011 ай бұрын
Nice job. I have installed several on cars-trucks and dune buggies. But I'm doing my 641 Workmaster - Propane conversion and Pertronics. Coil and points conversion kit. Finishing up my Nash Fuel propane conversion that I fabbed all of the brackets and plumbed all the hoses. I have owned this tractor for almost 20 years . Bought it off of a retired Firefighter that took very good care of it. This propane thing is someting to behold . Tired of the bad gas sitting in the carb , tank and all that intales . I wish I could show you some of my work. I'm 70 - grew up with hotrods and motorcycles . This propane thing is a challange . Thanks for conferming the installation for the pertronics.
@richardpittman6965 Жыл бұрын
Thanks for posting. The set I ordered on Amazon did not come with instructions. It looked pretty simple but after installing on my 602 it would not run. After watching your video I realized I had it installed wrong (CC rotation). After correcting and installing on the clockwise holes it now runs like a sewing machine!! Hopefully it will outlast the condensers I was having to replace every few months.
@randallsears12533 жыл бұрын
I did the same thing- ordered the positive instead of the negative. It took me several hours to figure it out. Stupid! Yesterday's Tractor refunded my money as well. Good people! Thank you for your video! I learned a lot!!!
@Rdrake14135 жыл бұрын
I installed one on my 1950 IH Farmall Super A. It is a very simple upgrade. I have my IH converted to a 12 volt positive ground. When I installed mine the only issue I had was the tractor wouldn't start. Adjusted the timing and it hasn't missed a lick since. I installed mine about 3 years ago.
@davidmorar7773 жыл бұрын
Great video. Looking forward to converting my tractor
@elixruiz84402 жыл бұрын
The ballast resistor is for the coil and the wire on the coil comes from there by way of the ignition switch. Check your ohm reading at both places and just see what you get. Don't forget to disconnect your battery.
@boatingfisherdude5 жыл бұрын
great job and video
@SakimasRidgeHomestead5 жыл бұрын
Thank you!
@billyelkins4413 жыл бұрын
I remember there was an issue with the dust cover either you left it off or cut the center out to make it fit over the exciter ring.
@dantihon3997 Жыл бұрын
“Capacitors are passive electronic elements with the ability to store electrical charges. A condenser refers to a device that can transform a substance from its vapor state to a fluid state. “
@SakimasRidgeHomestead Жыл бұрын
Impressive you can look up definitions in a dictionary, but anyone who has worked on a pre-electronic ignition vehicle knows the ignition capacitor is referred to as a condenser.
@jeffreygleaves29314 жыл бұрын
Good video. I wish you would have shown how to deal with the ignition key/resistor hookup. That's where things get vague for me. I'm converting a Ford 3000 and the instructions are terrible. There's no adjustment for the sensor even though they include the acrylic gauge. The magnet doesn't sit flush with the top of the sensor when all the instructions/how to videos say it has to. After a call to Pertronix they told me it doesn't matter on this particular kit. It would have been nice if they would have mentioned that in the instructions.
@jacobphelps22103 жыл бұрын
Easier than putting in new points and condenser. I might do that next time instead of new points.
@___PK__2 жыл бұрын
Just ordered one for an IH 300. Thanks for posting the demo. Is it still going after 2 years?
@paulstropkey45164 жыл бұрын
Nice video! Did you have to change the gap on the spark plugs? Someone told me you have to make the plug gap slightly larger than the original spec.
@SakimasRidgeHomestead4 жыл бұрын
I did not change the spark pug gap. I do not recall the instructions mentioning you may have too either. The only grey area is if you need to add the included resistor or not which seems to be a "try it without it, add it if you need to" method. Increasing the gap should give a little hotter spark I believe.
@paulstropkey45164 жыл бұрын
My mistake. Changing the spark plug gap is if you use the coil Pertronix recommends. I found that out after I asked you. Thank you for responding.
@inkbythebarrelandpaperbyth69052 жыл бұрын
Do you have to cut the center of the dust cover out so that it can fit?
@cdlvj10 ай бұрын
The site Steiner highly recommends a change to high energy coil, and spark plug wires. Whey did you not do this?
@georgem.kokindajr.9417 ай бұрын
Nice job! I’m assuming your timing is 8 degrees before TDC. Am I correct? Also do you have a link to ordering the timing light you have there? It’s a lot better than the one I have. One other thing, when you changed your system to 12 volt do you have a video on that? Mine is 6 volt positive ground. Not sure if I have to change the starter and coil for a 12 volt system. Thanks!
@genesisfarmhomestead20173 жыл бұрын
We converted our Ford 640 to a 12v system but can't get it to start. Will the electronic ignition a must to be possible to the resistor as ND not the Coil?
@cdlvj10 ай бұрын
I assume Neg Ground. Check the voltage on plus side of coil. if less than 12, then you have to run that wire back to 12 volt side of ignition key. Also look at the steiner site as they highly recommend the high energy coil, and also have part numbers for plug wires.
@jimbuford41474 жыл бұрын
Somewhere I read that if it is negative ground the wire from the distributor should be attached to the positive post on the coil and opposite that if it is positive ground. Someone else said it doesn't really matter. Confusing to say the least.
@SakimasRidgeHomestead4 жыл бұрын
They make four different part numbers of these units. 6 volt - ground, 6 volt + ground, 12 volt - ground, and 12 volt + ground. I accidentally bought the + ground one and it would not work at all. If I remember correctly they did hook up to the coil differently.
@harveymiller68917 ай бұрын
What do you do where do you find how to operate a timing light I never have operated one
@yamaha1675 Жыл бұрын
What's the difference in the positive and negative ground. I got a negative wire going to distributor from coil. Is that a negative ground? It is a 12v conversion. I don't want to order the wrong one either..thanks
@SakimasRidgeHomestead Жыл бұрын
Which battery cable goes to the body (ground) and which goes to the starter switch? The cable that goes to the body is your ground. Positive cable = positive ground, negative cable = negative ground.
@cdlvj10 ай бұрын
Most folks also say that you should replace ground with that braided type. Makes it easy to identify.@@SakimasRidgeHomestead
@henrysosebee92412 жыл бұрын
How about the plug wires no metal wires
@hillbilly5538 Жыл бұрын
How much did it cost?
@kentrogers1616 Жыл бұрын
How do you determine if you have C or CC rotation?
@Derekmartin20 Жыл бұрын
I took cap off and watched the way the rotor turned
@singhananta81424 жыл бұрын
How can i get that? Im from Thailand.
@SakimasRidgeHomestead4 жыл бұрын
I purchased mine from Yesterdays Tractors, not sure if they ship to Thailand or not. www.yesterdaystractors.com/cgi-bin/store/model_parts.cgi?SearchArea=Ford&&md=Jubilee&cat=Electrical%20System&r=mcats
@michaelcobleigh47342 жыл бұрын
Send me the old one
@James-xo4uv4 жыл бұрын
Why not check the package, to see if you have the right system, instead of destroying a good system to get a new one free
@SakimasRidgeHomestead4 жыл бұрын
I obviously assumed I had purchased the correct part when I installed it. Only after the tractor would not start and quite a bit of head scratching, did I discover that it was the incorrect part. I thought I explained pretty well in the video that Pertronix instructed me to cut the wires and offered to send the correct part after I sent them a picture of the wire cut off the igniter.