Intermittent no start, no crank issue found. Freightliner, International, Kenworth, volvo, etc.

No video

Intermittent no start, no crank issue found. Freightliner, International, Kenworth, volvo, etc.

Рет қаралды 44,685

Күн бұрын

The importance of carefully inspecting the fuses, even if they are not blown.
Had an intermittent no crank/ no start issue here on this 2013 Freightliner. Found the problem to be loss in power to TCM caused by a hairline crack in fuse.

Пікірлер: 73

@1slayerfan834 Жыл бұрын

I'm a power company fleet mechanic and this video saved my butt with a bucket truck broke down on the side of the road at rush hour in Washington DC I can't thank you enough thank you

@OscarG6699 Жыл бұрын

Bro idk how too tell you this but my truck is kinda doing the same thing... It wasn't easy like this but I noticed a lot of freightliners are going down right now because of a issue like this 😂😅

@OscarG6699 Жыл бұрын

I only commented because you posted that comment 2 hours ago man💀

@AcousticHills 11 ай бұрын

Glad to hear! Happy to help a fellow tech. Keep fighting the good fight!

@OscarG6699 11 ай бұрын

@@AcousticHills hey man!! Update It ended up being the TCM I was able to trick the BHM and had the truck idling for 2 hours while the TCM was chilling in the Ice Box then turned off the truck. Plugged in the TCM and everything was operating good Ordered the new TCM and Truck is running smoother then ever 😎

@AcousticHills 11 ай бұрын

@@OscarG6699 Good to hear! 🤟

@orlandocruz7975 Күн бұрын

Had the same codes start only after sitting for a few minutes and wouldnt start after till system got cold , found bad fuse f3 , 10amp saved me time thanks

@elnino3488 27 күн бұрын

Thank you so much that was my problem hair line crack 👍🏼👍🏼

@AcousticHills 27 күн бұрын

@@elnino3488 great! 💪🏽 glad to help!

@undertharock Жыл бұрын

Crazy, a simple fuse. Going to go check mine now although not automatic, having the same intermittent no start issue. But I also have a clicking sound coming from my starter area too.

@AcousticHills Жыл бұрын

Sounds like a bad spot in your starter. Should replace the starter if you hear the solenoid engage and still no start

@arceniovalenzuela6590 11 ай бұрын

Great job of diagnostic

@AcousticHills 11 ай бұрын

Well thanks!

@danielclark2864 Жыл бұрын

Very interesting and thanks for sharing that man!

@ronunderwood5771 7 ай бұрын

Very good find. I did not realize that a loss of VSS points to a TCM not powering up. Good to know. BTW I have used one of those Bendix RDU's for a long time. Even built a long extension harness to take it into the engine compartment or under the truck when shaking wiring looking for intermittent power loss to a module.

@vicpetrishak7705 10 ай бұрын

An incandescent light bulb and a headlamp is also handy for placing electrical loads on wiring or fuses . Chinese fuses appear very low quality . Very WELL DONE DIAGNOSTIC CHALLENGE !

@klaromio 8 ай бұрын

Wow. Thanks for sharing

@timstanford3443 Ай бұрын

I had exactly the same issue on one of these a while back ago. Frustrated me because I checked the fuse first thing. Lol

@AcousticHills Ай бұрын

Haha, yea this thru me for a loop 🤣 Good wrenching out there brother!

@roundcornerent Жыл бұрын

WOW thousands of dollars . AND all it was was a fuse . but that was a tricky one .

@rattydon25 3 ай бұрын

I am having the same issue. And the shop changed my tcm but the is still there.

@AcousticHills 2 ай бұрын

Ooof, sorry to hear that.

@TheBmco99 Ай бұрын

I had this exact same thing happened to me

@MahA-pr7kr 6 ай бұрын

Hello. Freightliner Cascadia 2016 Auto. The truck won't start the tractor's ABS light is on and the DEF light is red Flashing No check engine light. The dashboard screen does not show the transmission message and the screen just stuck with Underscore marks.

@AcousticHills 6 ай бұрын

Hey there. See if you can hook up to the ecm and see what the codes are. If you cant and it's not cranking. I would check for power and ground to ecm and tcm.

@Shaggyxs 3 ай бұрын

I have a mack pinnacle cxu mp8 mDrive that turns off the engine while draving it, and abs, atc, and the ⚡ symbol starts flashing, the rpm indicator star going up and down. I stop on the side of the road, take the key out, give it a break to turn off the cluster and try to start it agan, some times it cranks and starts like nothing happened and other times it takes more tries. It happened to me today like 8 times in the road while draving. You think something like that could caus it? I have no idea whats wrong with it

@AcousticHills 3 ай бұрын

Yea, sounds like you have an intermittent loss in power. Corrosion or rubbed thru wiring. If it gets worse, then you'll have to find the bad power circuit. Start with batter connections and work your way up

@user-nz9lu4br2b Жыл бұрын

I have Exactly the same problem, I check the fuse. Not the ground with the outer place. The new fuses I most of users I change but I have Sam problem. The truck is not moving right now. It's not cranking transmissions, it's not connect. Not communication on the transmission even to the dashboard.

@AcousticHills Жыл бұрын

Check power, ground, ignition power and datalink. Of that's all good, you have a failed TCM.

@robertrichardson1671 2 ай бұрын

So much better than the old manual trucks what a joke

@josueesquivel5336 7 ай бұрын

Is this also for manual? I’ve check ground cleaned them up and also change batteries cables. Still intermittent starts and at some point start to crank for a sec then stops

@AcousticHills 7 ай бұрын

I would check the clutch switch. Also see if it happens when lightly pressing the clutch pedal vs pressing it hard

@donttruckhere Жыл бұрын

.Freight liner cascadia 2018 stuck in manual mode wont start, found no power in the 21 pin connector at 1,2,3,4, and 6. Any idea? Could it be a TCM fuse

@AcousticHills Жыл бұрын

If the display is lighting up then not a power issue. Need to scan TCM to see what its doing. If it thinks its in neutral, codes, etc.

@edensguerrier2655 6 ай бұрын

Where about are you??

@AcousticHills 6 ай бұрын

Ontario, canada

@user-pj9hh9gd3f 6 күн бұрын

👏👏👏👏😮

@torrickbradley2031 Жыл бұрын

What fuse was that, I have a 2018 Freightliner cascadia & I believe I am having this same problem?

@AcousticHills Жыл бұрын

TCM fuse. Hope you get it and save thousands!

@bcm20003 Жыл бұрын

Where you located?

@nickyerally9735 Жыл бұрын

Where u located

@alongwang3582 Жыл бұрын

Hello! How about freightliner shut off while driving and check engine light come out? No crank no start. SPN 625 FMI 14. Fault was MCM system ID has stopped receiving or stopping. Any ideas?

@AcousticHills Жыл бұрын

Sounds like you're losing power to your MCM. with key-on, wiggle your relay/fuse centers at the firewall and harnesses. If you hear clicking and stuff turning off and on then you know you got bad wiring and you'll have to find what wire, fuse or relay causes this while getting wiggled. Good luck man, hope you get it.

@alongwang3582 Жыл бұрын

@@AcousticHills Thank you for replying! I will try it tomorrow morning.

@scottbritt9058 Жыл бұрын

What obd connector is that and where can I get it ?

@AcousticHills Жыл бұрын

The tool is a BENDIX J1708/J1939 data monitoring tool. Can be purchased online thru bendix or thru the parts side of dealerships. Forget the part number but a Google search will do the trick.

@WiseMann Жыл бұрын

We are having similar issue on a 2016 KW T680 eaton 10spd automatic transmission. After replacing batteries with new ones engine wont start with key or even crank but will start by shorting the starter. Then it wont shift into gear. Truck has been parked for over 6 months was running before. We asked a guy who does diagnosis for trucks to check it out with computer, he diagnosed and said that the system is not detecting the TCM, and to replace the TCM. Have checked the fuse and looks fine, the voltage reads 12.5V. He says TCM must not have power. Any suggestions would be appreciated. Thanks!

@jamescraven5540 Жыл бұрын

there is a 30 amp fuse ( breaker) metal looking. by foot panel,, loose connection or it fell out .or it is bad. top right of panel

@AcousticHills Жыл бұрын

Definitely check your power and grounds at the TCM, they'll be on the front connector if its an ultrashift tranny, the big round terminals on the corners. Then check ignition power circuit at TCM and j1939 datalink for CAn +/- voltage. Kenworths need a special adapter to hook up to the TCM or any other module (other then ECM), its a dumb idea on KW side. If all is good at the TCM, then yes you have a fried TCM.

@AcousticHills Жыл бұрын

@@jamescraven5540 Oh nice, you found the problem? sorry I didnt see this reply till now.

@JAMESLCRAVEN Жыл бұрын

@@AcousticHills wonder if he read our comments and if it's fixed, mine did exactly what he was saying .and got fixed asap .stupid fuse.

@Rico77777 Жыл бұрын

What if you don’t have power to either side of that fuse but all other fuses have power?

@AcousticHills Жыл бұрын

Then you'll have to chase that wire to a power junction. Check the batteries and cables at the batteries.

@Rico77777 Жыл бұрын

The only weird thing is that there’s no power to the one fuse F10 5AMP on the same box and I would hate to replace the whole wiring harness because that box does not want to come apart so I can see where the fuse connects so I can trace the wire continuity. Thank you for your help.

@AcousticHills Жыл бұрын

@@Rico77777 make sure you're testing with key-on. Check any power junction or buss fuse that may provide power to multiple circuits. Yea you don't want to be replacing harnesses if you're not 100% sure. If you don't know, it's best to take it to a dealership

@markwilliamson5207 10 ай бұрын

Repercussion of low pay techs for dealers top charge. Techs have productivity rates they should meet or have to meet..... in a tech world it makes it difficult.

@sardorodilkhujaev-ok6db Жыл бұрын

How we can contact u?

@KenMorelli Жыл бұрын

I have the J1708/J1939 diagnostic thingy like you have and I also have the Ancel diagnostic tool and the first tool doesn't have any ECU and the Ancel shows no communication. Bit it acts like a start inhibit issue. I can jump the stater relay and it will crank but won't fire. Could it be the TCM like you say or power to it ? I've checked and double checked everything. Am I missing something ? It's kicking my ass for sure. Any info will be helpful....

@AcousticHills Жыл бұрын

With no TCM on the datalink, it will not start. It needs the TCM to tell the engine it's in neutral to crank. So if you have no TCM showing on datalink or you cannot connect to the tranny, I would definitely check for power and ground at the TCM. If you have good power, ground and datalink, then you have a bad TCM (which isn't uncommon).

@KenMorelli Жыл бұрын

I assume that even though the shift indication on the dash works to tell you which gear your in the TCM could still be bad ? Thanks for all the info greatly aides me in repairing this beast.@@AcousticHills

@KenMorelli Жыл бұрын

@@AcousticHills One last question I promise....Do you buy a flashed unit or does the dealer jut reflash it ? Sorry to be such a pain in the keeester...

@AcousticHills Жыл бұрын

@@KenMorelli if you have a 3000/4000 allison, you will have 'cat eyes' on the display shifter in the truck if there's no comm to the TCM. Should still be reading -- or n/a in the dash with 1000/2000 Allison's. Just double check your power, grounds and datalink to the TCM before condemning it. Check the fuses, etc. If you buy a new TCM, you will have to remove your old one and give it to the dealership where you'll buy a new one. There's a calibration code that they will have to have allison program in it when they order. Best of luck!

@KenMorelli Жыл бұрын

@@AcousticHills Thanks soooo much for the info.....I believe it's a 3000 series with a push membrane not a t-handle shifter....I saw the TCM mounted right above of the driveline where it comes out of the trans....Must be an engineering thing to put in the open like that instead of in the cab where there's no water intrusion etc. I'll double check the grounds and voltage to the TCM.....

@gerryr8400 Жыл бұрын

SOS I NEED YOU HERE IN DAYTONA BEACH FLORIDA I got 2018 freightliner cascadia dd15 won't crank or start. Got new Sam cab and new pndb block and new starter and still won't start 🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬🤬

@AcousticHills Жыл бұрын

Check for codes in all modules, make sure they are communicating. If no codes and all modules are communicating, you need to see if your getting power to your 's' terminal on the starter solenoid while someone cranks. Then go from there