iPad Mini Charging port flex cable Soldering and Replacement

Рет қаралды 15,933

5 жыл бұрын

⭕ Ask questions and Engage in our Forum at northridgefix.com/forum/
⭕ Need a repair? northridgefix.com/mail-in/
⭕ Visit our ecommerce shop and buy all your tools at northridgefix.com
⭕ We are an Amtech Flux Distributor. Buy AMTECH NC-559-V2-TF Flux
northridgefix.com/product/amt...
Microscope northridgefix.com/product/mic...
UNI-T UTi260B thermal Camera
northridgefix.com/?s=thermal+...
Grinding pen
northridgefix.com/product/gri...
Low Melt Solder
northridgefix.com/product/low...
NorthridgeFix T-shirts
northridgefix.com/product/nor...
Weller Soldering station ebay.us/1mvgt5
=================================================== If you are local, drop in and say hello
NorthridgeFix
19365 Business Center Drive, Unit 7
Northridge, CA 91324
Phone: 818-668-7058
NorthridgeFix.com

Пікірлер: 28

@MikeSmith-qw9ow 6 ай бұрын

Great vid. Wish me luck! 3:53 That was brilliant 😮

@amanda.bowers 4 жыл бұрын

I just wanted to thank you! I’ve never soldered anything before and you made it look so easy! So I tried on an iPad with a broken charge cable and I just fixed it! Super excited! Definitely liked and subscribed! Please keep making videos!!

@bobbymoreno2452 2 жыл бұрын

great job easy and simple and right to the point explanation

@sapirpro7321 3 жыл бұрын

bruh u deserve a gold medal for your vids they are so good , thank you u earned another sub :)

@donnierobertson3088 4 жыл бұрын

Great job again

@balaa7053 3 жыл бұрын

Great job sir, awesome.thank you for video

@justinspiredfallout 5 жыл бұрын

Great video as always, man! I've avoided iPads so far, opting to take in only Android based tablets that don't require heat and adhesive kits to open/close them. I'm pretty nervous about working on these and I haven't been able to find any cheap dead ones that I can practice on yet. :(

@ashrafbashreef3523 2 жыл бұрын

good job

@p.r.5306 5 жыл бұрын

Nice work, Nice video! Which cam do you have on your microscope? Salam and greetings from Germany!

@pawelpodlesny2366 Жыл бұрын

super!

@diegom7771 4 жыл бұрын

Hi my friend. Great video. I´ve done same repair than you in my Ipad Air and the flex charger port is already installed. I´ve checked the connections and it seems all are correct but once I´ve connected the charger to the new USB port (5.2 volts.), I´ve detected 1.4 volts. only in the motherboard battery pads (without the battery fitted). Which voltage should be in these pads? 3,7 volts? I cannot fit the battery as it´s gone. It´s dead. Before to purchased new one, I need to know if the repair is properly done but that 1,4 volts make me suspect that something is wrong. Can you help me? I´ll appreciate a lot. Thank you.

@MansoorMansoor-lx1re 5 жыл бұрын

Good

@bigdowglb 3 жыл бұрын

Did you poke holes on the connecting pads are did you buy that from somewhere like that?

@88bayar 3 жыл бұрын

Which type of microscope you are using ?

@BTBAB-yj1cn 5 жыл бұрын

Thanks and keep up the great work! Is the technique for this basically as you have mentioned before: 410 iron when mixing unleaded with low melt, 350 air when removing connector, 350 iron to solder connector back with leaded?

@WarrenGuan 3 жыл бұрын

Are you talking about Celsius or Fahrenheit?

@justinrussell3495 2 жыл бұрын

What is the gel like substance you apply when you say you are applying low melt solder at the beginning of the video?

@smdsoldering 2 жыл бұрын

Flux

@tomsommer54 Жыл бұрын

I was wanting to know how to fix a broken cable. I can see a broken wire on m cable mini side.

@Cjdust 2 жыл бұрын

accessory not supported problem while charging can u fix it?

@danielyancey9356 3 жыл бұрын

Do you have any videos on how to fix a lifted pad from one of those iPads? Thanks!

@melikeymalarky4460 Жыл бұрын

Did you ever find out? I’ve got that issue right now.

@scxr1526 2 жыл бұрын

How much will this cost

@melikeymalarky4460 Жыл бұрын

What happens if you pull a pad off?

@MorrisLiveProductions 4 жыл бұрын

where do you get the microscope from? Thank you!

@johny1220 3 жыл бұрын

His website has it man lol, I got it from there and it’s pretty awesome ngl 😄

@floridaapplemacprosinc.2224 2 жыл бұрын

With respect, the reason you had problem with seeing the alignment windows is because you filled in the alignment X with solder. next time if you use care not to fill in the alignment X with solder, you will be able to see the X through the window, and align the cable perfectly without making holes.