iPhone 12 Pro Max - How to Solve a Brain Dead Amperage Draw (Stuck Low)

Рет қаралды 10,319

10 ай бұрын

In this livestream I will attempt to solve an i12pm that has been dropped from a rollercoaster. It is currently stuck at .07a on dcps and in this video we will see if it can be recovered.
If you want to send in your own iPhone for data recovery, fill out the intake form here: www.iboardrepair.com/
Join my iPhone Motherboard Repair & Data Recovery Discord Server:
/ discord

Пікірлер: 35

@adammirage4261 10 ай бұрын

Excellent repair as usual !

@iBoardRepair 10 ай бұрын

Thanks for all the support!

@gsmrepairtech5743 5 ай бұрын

big respect ❤ i really like your videos on details

@MicroMageRepair 10 ай бұрын

Outstanding information as always.

@iBoardRepair 10 ай бұрын

Thanks for always stopping by buddy!

@NOONFIX 10 ай бұрын

It's a really good repair man !!! Definitely going to watch this again. Can you make a video about power rails and what to test?? And what is necessary to boot??

@iBoardRepair 10 ай бұрын

I probably won't make a dedicated video but you can kind of pick that info up as you watch!

@joziphstu 6 ай бұрын

Currently have a “brain dead” iPhone 11 Pro Max, I tried to start this checking process you were doing on the caps near the coils, I just gave up cos I didn’t think I was doing the right thing, seeing this video has given me confidence to want to resume my checks, hopefully I’m able to solve it Great job 👏

@iBoardRepair 5 ай бұрын

Give it another shot!

@sharfazhameed6382 7 ай бұрын

My new favourite channel

@iBoardRepair 7 ай бұрын

Thank you bro

@chrisjohnsonnagbe775 10 ай бұрын

very educative

@teamgiveaway3483 10 ай бұрын

Thanks, man. I really appreciate your time and effort put into this. I would have preferred if it was the pmic that was bad so I could learn how you remove and you replace it 😆 My question here is that. Does using the multimeter on voltage mode to measure reading also apply to diagnosing baseband problems? I really just learned how to use that mode on this video now

@iBoardRepair 10 ай бұрын

It's a lot harder to measure voltages on baseband because I am not sure at what point which are supposed to be turning on. You would have to discover that yourself!

@mukeshthakur3778 7 ай бұрын

Veri nice job no swiping ✌️👍

@Med_314 10 ай бұрын

Good 1👏🏻

@yosie73 9 ай бұрын

tnx man

@eLab43 10 ай бұрын

Thanks you so much! Question: theoretically, before you went for pm ic swap, could you see on the schematic v_in line of the ram before it goes to pm ic, and v_out after the pm ic? Thanks you

@user-bx5qh1dz1f 10 ай бұрын

Brat ishlaga omad

@gsmrepairtech5743 5 ай бұрын

love from united Arab Emirates ❤

@iBoardRepair 5 ай бұрын

Thank you!

@alexandermadziva3395 20 күн бұрын

What’s the name of that spray

@malkhafizalmalkhafizal5913 5 ай бұрын

Same with my iPhone 12. Drop from car. Already changed the new lcd glass screen. But cannot power on and no apple logo when put in the charging cable. Im already fast reboot but still cannot on. What is the major problem

@kelvinsmith533 9 ай бұрын

❤❤❤❤❤

@iBoardRepair 9 ай бұрын

Thanks for watching!

@katendemalcom836 8 ай бұрын

I have a12promax with the same issue though the problem seems ti be with pp GPU

@dryjokes608 5 ай бұрын

Same problem for ipxsmax low current what to do? Plz master

@iBoardRepair 5 ай бұрын

It is different every time, it must be diagnosed.

@dryjokes608 5 ай бұрын

@iBoardRepair everything is OK I have measured every line it's normal and stuck upper board at 70-80MA

@dennispowell7719 9 ай бұрын

Hi I have a iphone 12 pro stick on low amps of 0.37 vdd main vdd boost are not short and all caps around nand are not short phone wasn't dropped damaged or waterdamaged can any one point me in the right direction ? thanks

@iBoardRepair 9 ай бұрын

You should check pmic outputs, one is probably missing

@dennispowell7719 8 ай бұрын

Hi araon with regards to my iphone 12 pro I messaged you about I have found a line that is short the 1v06 line does that mean the cpu is short as I've injected 1.2 volts into that line and only a very small section of the cpu just above the letter a on the cpu gets hot am thinking I will have to remove the cpu and check the line again what would you suggest thank you