70!!!! Wow!!! When you put the edge you did under the microscope I said "That's gonna go through a deer without it knowing it was even hit!".

You’re a fantastic teacher. Amazing how well you broke this down. I appreciate it.

Great video Ron. 70 on the sharpness tester is amazing.

Awesome video. Learned a lot, thank you

Great content, look forward to each one... Can you post a tanto tip and tip sharpening for single bevels...? I’m a fan of and use Tuffhead and Iron Will . Mahalos!

Hoping to see a Kayuga Pilot getting worked on your channel soon. Great channel you have here! 👍

Pls do a tutorial on all the edges. You kind of did it in your last video but skipped over the front edges pretty quick. Please make a full tutorial sir!! Lol

Wow!! Great Video sold on both!!

Impressive head. Any guidance on sharpening the front angle/tip? As simple as turning the blade in the sharpener?

Do you sharpen the tanto tip also?

How long did it take to reach the first burr with 240 grit? I thought I had a burr at each step but I’m starting to doubt myself after testing with a rubber band.

How about sharpening the tip? I see it asked Alot but didn't see the answer. Thanks

If treated with Hornady one stop will the heads need to be resharpened over time if not used but only remaining in quiver exposed to the elements both indoor and out?

Apparently, my timing was spot on this evening. Incredible job sharpening that head to a razor's edge. Have you considered selling your sharpening services? As in reselling broadheads that you have sharpened to your high standards? Just a thought. Thank you for the fine video

What grain diamond plate is best to start with after shooting into foam target a few times

How do you sharpen the front edge? The part that makes first contact?

How do you sharpen the tanto tip

Ever seen one of those jigs w the TPU plastic corner touching before the roller? One side of mine seems off but I’m brand new ever trim the frame to make sure roller is even?

Very nice. I know it’s not a single bevel but anyway you could do a video showing a tooth of the arrow head? Great stuff.

Is the kme sharpening system steep enough to sharpen this head?

How would a whetstone do with these? Thanks,

How do you resharpen the tip and bleeders?

Where you get the 2500grit diamond

@Innovative Outdoorsman, I know diamond plates are not completely necessary but I was wondering if you could offer the grit ranges you go through and what brand diamond plates you prefer.

Another great video as always! I've never shot or owned single bevel broadheads.... im thinking about trying them sometime. What single bevel broadhead do you recommend?

Ron, I ended up ordering the single bevel one with the bleeder blades before reading your comment on the bleeder blades. I’m mainly shooting whitetail deer with them and figured the bleeders would give better blood trails. I don’t know if it’s a myth but I had heard that the single bevels leave less of a blood trail. That doesn’t make sense to me. Anyway. My questions after rambling is on sharpening the bleeders. Is it worth doing and can I use the same guide. I believe they have the same angle bevel.

Love your videos! Have you ever shot Right Bevel, right helical even though your shaft rotates left. I want to shoot iron will single bevel but they do not make a left bevel. Any insight. Thank you

Awesome video. Do you have a Maasai sharpening video?

I bought this along with the set of 5 diamond plates, and went down to a piece of cardboard , but am still having trouble getting shaving sharpness. Without any tape, it’s only taking material off the back end of the bevel, so I had to put Lots of tape on the roller to get it angled properly to sharpen the leading edge. It probably took 40+ strokes to get a little burr, and it’s difficult to hold the blade flat to knock the burr off without removing the blade from the jig, and then re-aligning it again. I just can’t seem to duplicate the results in the video, no matter how long I spend on it. - frustrating!

Man idk what I'm doing wrong but cannot get these blades sharp

I’m sure it’s been asks before but where does one purchase that rolling jig you used to hold the blade?

What could i do if i wanted to remove that line from breaking off the burr??

Looks like one of those sodium bulbs you have for the roller.. They will hone a knife ..

Holy shit 70 thats. Nuts

A great system for those in the USA. It is not sold anywhere else.

Where did get the steel sharpening plate from

Sorry, forgot to add. Compound bow.

Your iron will came sharp? I'm highly disappointed in mine, I've been sharpening it for over an hour and still won't even cut paper. Like they forgot to put an edge on it. Out the box I could apply pressure and drag across my finger and it not do anything.

I had vented 100gr not single bevel come unscrewed as it passed thru a small deer/spine. Dead deer no broadhead on end of arrow. Iron Will won't replace my lost broadhead. Oh well!

Why the "no need for bleeders on a single bevel." Single beveld is totally new to me. Just wanting to learn all that I can.