I'm only 14 but I watch your vids a lot because I feel like it helps me learn incase I want to pursue hvac as a carrier

Your pressures look pretty good for what it is. I would had done the same if I saw my superheat heading towards zero

Great job. Another good video!

final vapour line temp at 46 F was good, 10 lbs as per factory charge is good, + additional charge for lineset length over 15 or 25 ft. best to look at manual by looking up model # online. Good job , Badmans, they love to leak.

Most Goodman txvs are adjustable and they are a pain. You have to put an adjustable wrench on bottom of txv and open or close depending on where your superheat is while you're checking your pressures. It helps having wireless probes.

Thanks for getting the people air and thanks again for the video

job well done.. good job..

Hi, this is Jermey McGuire. From Lake Corpus Christi, Texas. You did good plugging up the leak on the air conditioner, I recently got 2 brand new air conditioners installed back on Wednesday 4/10/24 and Thursday 5/11/24 I personally had a 5 ton Lennox XC16 air conditioner from 2009. And a 4 ton Goodman from 2018.” The Lennox air conditioner went out the blower Moyer had to get replaced last July. The 1st fluke I had with the old 5 ton Lennox was the high pressure switch it tripped. In July 2022, then a year later. 7/7/23 the blower motor went out. I finally got it fixed on 7/17/23, it was time to get the air conditioner replaced.” Before I was going to get my upstairs air conditioner replaced my downstairs air compressor broke down. And the Lennox gas furnace was completely shot, it was rusted out very bad. The heating exchanger was cracked the only thing was working was the variable speed blower motor.” Before my old upstairs air conditioner wouldn’t cool under 80 on the thermostat.” Now I’m keeping cool!! I don’t have to worry about any air conditioner break downs.

Awesome content brother

Good stuff brother. Keep killin it 🤙

BTW your camera is fine. Don't worry about these "latest and greatest" pimps. Good content always beats technology. 5 minutes ago they didn't even have what you're using.

Good work

Great job bro

Nice one🎉

New to the Channel, Nice Job!

It's funny hearing somebody thinking out loud the things I would think

Just subd, brother Keep doing ya thing brother

Aruf don’t have txv installed from the factory. Aspt and avptc have factory installed txv.

Ur doing a great job for ur company.. Sounds like an additional problem on the dry side. Air filter or coil. Could also b an improperly sized coil and or txv.

Ayeee buddy was jamming! Love to see us men out doing what we supposed to! 🙌🏽🙌🏽🙌🏽 What's a voltage meter you recommend for a homeowner for diagnostics? Subbed! 🤞🏽💯

Great job... yeah, personally, I like to see the sub cooling up a little higher .. but without adjusting the txv.. you did a frwat job... glad that you take pride in your work.. Next time make sure the removed the piston ... I have came acroos same situation...txv externally mounted... but the never took piston out.. 😅

I heard badman and thought tenant. At the company there was a brand that starts with M and ends with G that everyone used to call icemaker.

It takes time for the expansion valve to open and close. the data tag states the amount of refrigerant in the condenser but not the line set and evaporator. 160 oz is 10 lbs. if you had a 50 foot line set you may add 1 or 2 more lbs to be fully charged. total charge on that unit would be around 12 lbs. good job sealing that leak but man it looked terrible.

Txv Goodman subcool is usually 6-8 degrees, but your 10 target is a pretty safe bet for most mfgrs. I dont want to say superheat doesnt matter but you cant control that too much unless the txv is adjustable; most Goodmans are. Make sure that bulb is tightly secured and is sized for the condenser as well. I cant tell you how many times Ive found the bulbs loose and thats all it took for my superheat/subcool to normalize. They are usually 1.5-3 ton txv or 3.5-5 youd have to check. They also make them individual size as well for the tonnage. Add the juice after ensuring your bulb is tightis good practice 👍, good job, doesnt help that this always happens on a friday

Nothing but the good JUNK 😂

Not sure whih AHUs they are but I ran into a lot of Goodman units that had Txvs and wanted SH/SC between 7-9 degrees and wad necessary to ajust the valve on a lot of coil changeouts. It was annoying sometimes even had to remove and add as needed

The txv regulates the super heat it will ramp up/down make sure coils are clean and u should be good

Good work man, just: - wondering how exactly was the txv bulb located? Could possibly be not in the right position so it’s allowing too much liquid refrigerant filling in the indoor coil. - then, how was the airflow? Blower fan was spinning at good RPM? would’ve also checked the blower fan cap. Just wanted to share some ideas and keep up the good work. Best!

Sometimes adjusting the txv we help

What do you think caused the puncture hole? I figured that it would be around the high pressure switch tap.

Wrap the txv with foam.

I work with thermoking truck/trailer units I know nothing about the super heat portion or really any HVAC but is there not a sight glass to see when it’s full or not.

I was a child myself once. I would have broke night. To make sure a woman and her child do not suffer.

I believe if they are properly mounted and covered, they should be reading correctly. I mounted my bulb on the inside and don't have any issues. It's also a Goodman. So maybe you're on to something. Keep up the good work.

I would have just brazed it up, you put enough nitrogen in it to not do any carbon contamination..

So crazy how much Freon those take down south. I’m in Kansas and never had more than 4 pounds in apartment condensers. You have to realize apartments change air filters twice a year if that so all coils are filthy and require more Freon to compensate because they ain’t paying to clean coils. Not in the budget. I can’t even believe they hiring you guys to work on them because that would never happen around here. 30 bucks an hour plus cost of equipment is very cheap labor at apartments to fix or replace units as an hvac apartment maintenance tech. When I was working at an hvac company that would have been 1500 to 2000 grand for that repair with 10 pounds of Freon and apartments will not pay that here. Good job anyway

10 lbs is a huge amount for a little 2 ton unit.

Like the video but would like to watch profanity

I have found that most of the service calls for a Goodman unit is due to poor quality work by the installers. Leaks at the burned up schrader valves, poor braze on the line sets. Not the machines fault, installers fault most of the time !!!!! Goodman's are excellent units, simple to operate and fix, unless you are one of the MANY poorly trained installers in this trade !!!! SEE WHAT I MEAN, POOR QUALITY BRAZING BY HACK INSTALLERS !!!!!