Satisfying footage of using a lane shark limb/brush cutter. I review the lane shark as I use it cutting shooting lanes for deer season.
Пікірлер: 43
@davidleblanc77828 күн бұрын
We are thinking of getting a lane shark. Your video helps me decide.
@andygeorge75510 ай бұрын
By far best Lane Shark vid I have seen, and I been looking at them for about 3 years. Thank you
@jimmerrithew4535 ай бұрын
It would be wise to strap the hose to the loader arm. Otherwise, you may snag the hose and snap it. Good video. Amazing work.
@bbkkssv11 ай бұрын
Looks great. I could see that hose getting ripped off if you don't pin it up
@worldsokayesthunter11 ай бұрын
Yeah definitely have to keep an eye on it. It's not a perfect setup but it's worked so far
@thecreeklifeoutdoors585511 ай бұрын
Great video! I am looking to buy a L3560 cab and pricing a lane shark to go with it. This is one of the best videos I’ve seen for the lane shark.
@worldsokayesthunter11 ай бұрын
Thanks for the compliment
@heathalford4721Ай бұрын
My uncle bought the L3560 cab. He wishes he would have got the 40 or bigger but it’s different for every one
@heathalford4721Ай бұрын
My uncle bought the L3560 cab. He wishes he would have got the 40 or bigger but it’s different for every one
@timothywoods8170 Жыл бұрын
Yes Sir it looks good!
@worldsokayesthunter Жыл бұрын
Thanks for the comment
@davidbergagnini204511 ай бұрын
Only tip I have is slow down some and it'll cut better. Your moving pretty good mine has done great. I'm not sure when you got yours but I would call lane shark give them your serial # and see if yours is the updated shaft and blade carrier
@worldsokayesthunter11 ай бұрын
I can't go slower without lowering rpm. Are you saying it will cut better at lower rpm?
@briansmith840511 ай бұрын
That can’t be the lowest gear, seems like the tractor is flying!
@worldsokayesthunter11 ай бұрын
@@briansmith8405 I promise. Turtle mode. 1st gear.
@brantyoungblood484111 ай бұрын
Can you please provide more info about the updated shaft and blade carrier? I’m about to purchase one and would like to know what to ask. Thx for the help
@heathalford4721Ай бұрын
@@worldsokayesthunterwell you know what gear your in but man it looked like you were hauling butt going through there I’d have guessed 5-6 mph
@edenfieldjared02 ай бұрын
Did you do the actual bushhoghing with it or just the trimming and finish with a pull behind? I didn't see that part only the limb trimming
@worldsokayesthunter2 ай бұрын
Pull behind
@mcgregorpiper29 күн бұрын
@@worldsokayesthunter That was my question also thank you for the answer
@stevenpringle78135 ай бұрын
How well does it work on hardwood limbs, like sugar maple etc.? Pine is pretty soft.
@worldsokayesthunter5 ай бұрын
The more brittle the limb the better. Flimsy limbs sometimes sort of get swatted out of the way. But to cut them you just have to crank up the rpm's and make sure your blade is sharp.
@everettware346611 ай бұрын
Bad ass, I’d probably zip tie those hoses.
@worldsokayesthunter11 ай бұрын
I originally had. But not quite the right spot so they got ripped off
@crawford32310 ай бұрын
I am having one installed on a Kubota L2501 this week ( 2023-9-7). We will see if this medium sized lower powered tractor and the LS-3 is compatible.
@worldsokayesthunter10 ай бұрын
Good luck. Let me know how it goes
@scag5210 ай бұрын
How do you like the lane shark ? I have a l2501 also.
@crawford32310 ай бұрын
@@scag52 As for the power, the L2501 seems matched and adequate. I usually run it a 1500 rpm or a tad more. Mainly is I want to keep the push into the woody type brush slow. I have a manual transmission and I can control it nicely. It is like a Swiss Army knife. You can't expect to use it to carve a yacht. Another words a Brush Hog (TM) type is going to be able to clear more but that is not what this tool should be used for. My house is in the city limits and backs up to a creek with a few acres of unimproved rolling gully mess which a rear mounted implement cannot venture. So it is the tool I need for this task. After I get it knocked down then perhaps a flail mower or Brush hog can maintain it but a rear mower cannot do what this can do. Having said this, I have cut though 2 inch plus Youpon and it leaves a mess. Some of this land has not been touched in 100 years. I have a back hoe which will have to be used to remove the stubble. Cutting and trimming lanes and paths is wonderful. I am 70 and retired. I cannot see me up on a ladder with a chainsaw or pole saw ever again when I can configure this cutter to take care of it in a matter of minutes. Two items I will have to say is, you have to respect the potential hazards of being around equipment of this type. Hose management is an issue. Watch dangling hoses. Pulling in and out of heavy brush, lose hoses can get caught on debris, branches whatever. I have come very close to cutting my hydraulic hoses. I have tried bungee chords and the issue is when the cutter is raised higher it exceeds the limit of stretch and they pop. At least wrap the lines with plastic wrap hose protectors. I have gotten debris wedged in the cutter enough to stop it. Nothing to do but shut it down quickly and deal with it. This was obviously at the limit of how thick a limb it could cut. Also how much length can you cut. A piece of 18" long could kick back and jam the blades. This has happened twice and I modified how I use it. It is a learning process. So to wrap this up, I really like this tool for the job it is intended for. Same goes for my grapple,backhoe and flail mower. The creek property defeated the flail mower. The Lane Shark will not be defeated.
@chickenhawk9264 ай бұрын
@@crawford323 Nice! Looking to get one for my L2501. I already have the 3rd function, they quoted me around $6000 for the laneshark. What did yours cost if I may ask?
@crawford3234 ай бұрын
@@chickenhawk926 I think the unit itself was around $4500 and although you have a third function there’s some other hydraulics that need to go with it. The deal is that blade doesn’t stop or it shouldn’t stop with hydraulic fuel in the line so they they have to have a circuit open up so the fluid and the blade can circulate and slow down on its own and that cost a little money.
@dwaynegaskin857011 ай бұрын
Did it make your hydraulic fluid in rear end run hot ?
@worldsokayesthunter11 ай бұрын
Yes, definitely. Doesn't set off any lights but it gets hot and you can tell the cutter gets a little weaker.
@douglasvine25163 ай бұрын
Dude you didn't show the lane shark in the video?????
@flynnanderson3736 Жыл бұрын
we have a row of pine trees and they are about a meter wide😅
@worldsokayesthunter Жыл бұрын
Gonna need a different cutter for that. Lol
@jbob12745 ай бұрын
Can you run your bush hog while running the lane shark?
@worldsokayesthunter5 ай бұрын
Yes. I've got that in another video
@anthonywalls328110 ай бұрын
I hope you got a bush hog going behind you to take care of the grassy run over also.
@terrysmall63379 ай бұрын
Do you run your bush hog at the same time ?
@worldsokayesthunter9 ай бұрын
Yes. Not all the time, but if the terrain is relatively flat I do. You can't lift the cutter if both are going.