Is NEJE MASTER 2S PLUS 40W A40640 the Best Machine for Your Needs? Watch This Laser Engraver Review!

Рет қаралды 16,824

2 жыл бұрын

In this video I will review and test the Neje Master 2S Plus A40640 40W laser engraver machine with my standardized range of tests plus some extra stuff. I have also added some more challenging cutting tests to see how well the machine cuts thicker stuff. This video will help you decide if this machine is the best for you. I will also compare the performance to the popular Sculpfun S9 laser engraver.
Read full review and see detailed test results here:
hobbylasercutters.com/laser-r...
BUY HERE: hobbylasercutters.com/go/neje...
Buy through the link above and use coupon code V010WZ38E9ZN for extra discount at checkout! (Valid until 29.1.2022)
You can also buy the laser module separately:
hobbylasercutters.com/go/neje...
Made possible by: neje.shop/
Buy at Banggood: bit.ly/3q2uwwy
USE PROPER LASER SAFETY GLASSES (O.D 6+):
hobbylasercutters.com/go/best... (you only have two eyes!)
Microscope I use: bit.ly/3y1o3TI
I hope you enjoyed this video.
And click that LIKE button! It helps a lot!
BUT DO NOT CLICK THIS - bit.ly/2BYOIoR
Subscribe for more and tell me in the comments what you like the most or what should I create next.
Follow me on Facebook and Instagram
/ jtmakesit
/ jt_makes_it
for spoilers on what I am currently working on, behind the scenes and other extras!
I get my music from here: bit.ly/2U8HISX
#neje #laserengraver #A40640

Пікірлер: 42

@sammcmoor 2 жыл бұрын

Happy new year JT, nice video again. Wich laser do you prefer, this Neje or the Sculpfun S9? Greetings

@JTMakesIt 2 жыл бұрын

It is up to your personal preference. I prefer narrower focus point and more stable mechanics, so its the S9. But Neje isn't bad either.

@MONKEY-vi7hx Жыл бұрын

Would like to see the neje e40 and e80 modules tested. :-)

@DyudyukVitaliy 2 жыл бұрын

Hello, I saw on one channel a measurement of the optical power of the Neje A40640 40w (which Neje used to call 80 w), and this module produced 8.6 watts of optical power - less than the Atomstask M 50 (with a smaller focus point). Have you measured optical power?

@JTMakesIt 2 жыл бұрын

No, sorry I don't have the optical power measurement instrument. They are expensive!

@andiksuar753 2 жыл бұрын

the difference is striking, the power of the neje is very large but the laser focus seems out of control, burns everything on the side, like it's not clean enough when cutting, I have a 30watt neje and it's not as powerful like video above, so I decided to buy a sculpfun s9 for my chrome stainless steel engraving needs I'm a little disappointed after watching this video, I hope my sculpfun s9 doesn't disappoint ,btw good video i like it

@kurtopalka5201 2 жыл бұрын

Where can I get that test file for the ATOMSTACK a5 pro

@pawerojewski9113 2 жыл бұрын

Great review! How do you think, will it cut 15mm plywood with air assist?

@JTMakesIt 2 жыл бұрын

Thanks! I think it could be done with good air assist.

@surpointtools284 2 жыл бұрын

kzfaq.info/get/bejne/eMiFnbN8utCrlXU.html

2 жыл бұрын

I have the "30w" neje (7.5w is the actual laser output) do you know what the actual output power is of this "40w" model?

@JTMakesIt 2 жыл бұрын

Somewhere is advertized as 15w, somewhere as 10w. I believe its 10w, and the 30w is actually 5w.

@TheRealRoGueMS Жыл бұрын

@@JTMakesIt according to Neje official website the N40630 is 30w with 7.5w optical power, and the A40640 is 40W with 12w optical power or 11w continuous output

@gamingdz1783 2 жыл бұрын

Does it make 3D night lamps ?

@maxic7612 2 жыл бұрын

Hello I have the Neje master 2s Plus N40630 30w. I was told when I purchased it that it would do all that it showed on the website that I got it from. But I cannot get it to even make a dent on the samples, the black anodised tag. I have purchased some different tags. But still nothing. There isn't many instructions with the machine to say what speed etc to use. I am using the Neje software V5.6.4. The burning time can go from 0ms to 100ms. It was set at 10ms when I log in. Do you have any hints. I have some Matt gold stainless steel name badges. It does nothing on these. Do I have to spray paint them with the black paint. I need them to be gold afterwards. Thank you.

@JTMakesIt 2 жыл бұрын

You should check that the laser is focused properly and the dot is the smallest. I haven't used the Neje software. Only Lightburn. For anodized you should use speed 400mm/min and full power. I'm not sure what is the burning time prameter. I don't have that in my software.

@maxic7612 2 жыл бұрын

@@JTMakesIt Hello I did a test on the focus. I also tried one idea I saw on a video, rubbing mustard on the metal and engraving multiple times. It actually works so I will try it again with more passes. Thankyou

@Georgeprospero 9 ай бұрын

Jt can you please suggest me a laser module that produces the engravings of the s9 and has 10w optical power?! because I purchased the s10 and the engravings are not as dark as the s9 and they are fading off.. thank you!

@JTMakesIt 9 ай бұрын

You should try going slower and with less (or more) power for darker engravings. I had great results with the S30 pro max

@Dancopymus 2 жыл бұрын

Although I don't fully understand English, I notice that at 9:45, the stainless steel engraving was better on the Sculpfun S9; Am I right? And the Sculpfun S10 must be even better!

@JTMakesIt 2 жыл бұрын

Sculpfun has smaller focus beam and can make more precise engravings, but the Neje has more power.

@Dancopymus 2 жыл бұрын

@@JTMakesIt Thanks!

@kaptluffy9295 Жыл бұрын

what is your recommendation between sculpfun s9 n neje 3?

@JTMakesIt Жыл бұрын

Haven't tried Neje 3, but personally I don't like the bad air management of thr A40640 laser module. It leaves a lot of smoke stains

@user-im4yn6gy9u 5 ай бұрын

I use neje master 2s plus software laser grbl 5.4.0 Windows 7 The device stops working in the middle of a file. What could be the reason?

@JTMakesIt 5 ай бұрын

Did you try with a different computer?

@jennicajimenez4913 2 жыл бұрын

Good day. What software did you used?

@JTMakesIt 2 жыл бұрын

Lightburn

@jennicajimenez4913 2 жыл бұрын

@@JTMakesIt thank you so much :)

@ricardossantos4198 2 жыл бұрын

can this engrave in metal ou silver ? thanks

@JTMakesIt 2 жыл бұрын

It can engrave stainless steel and anodized aluminium. I haven't tried silver

@gamingdz1783 2 жыл бұрын

Does it make 3D night lamps ?

@JTMakesIt 2 жыл бұрын

You can cut it from wood

@gamingdz1783 2 жыл бұрын

It can't cut transparent acrylic?

@JTMakesIt 2 жыл бұрын

@@gamingdz1783 None of diode lasers can cut transparent acrylic. It is physically impossible. You can only engrave it if you paint it black temporarily.

@gamingdz1783 2 жыл бұрын

What about laser k40

@JTMakesIt 2 жыл бұрын

@@gamingdz1783 I don't like it. It has very poor build quality and very small working area.