TRADING MY £500 CAR FOR MY DREAM £100,000 SUPER CAR

TRADING MY £500 CAR FOR MY DREAM £100,000 SUPER CAR | PART 18

Рет қаралды 12,341

2 ай бұрын

Is the engine in my new BMW broken? Let's find out after breaking down on it's first drive.
Donate To The Channel Via Paypal HERE: bit.ly/3u2yEMz
Join Patreon HERE: / georgeausters
The following links are affiliate links that the channel recieves commission for
Tools I Use!
Topdon Scan Tool: amzn.to/41esgCk
Milwaukee Impact Rachet: amzn.to/3vwtA9a
BMW Jacket: ebay.us/ZpdbIM
Nitrile Gloves: ebay.us/LehsUZ
Sealey Cordless Ratchet Kit: amzn.to/3bgAsKn
Small Dewalt Impact Wrench: amzn.to/2T4igdi
Big Dewalt Impact Wrench: amzn.to/39NOrEu
Dewalt 5ah Battery: amzn.to/39tRRhL
Dewalt Battery Charger: amzn.to/3dkwlxb
Impact Socket Set: amzn.to/3a8zcpQ
Torx Socket Set: amzn.to/32EbnDV
Female Torx Socket Set: amzn.to/2PzAZMQ
Digital Torque Wrench: amzn.to/3dlCP37
Torque Wrench: amzn.to/2VF0YpI
Oil Drain Pan: amzn.to/3dm00pJ
Rhino Ramps: amzn.to/3zKGiy7
Jack Stands: amzn.to/3pTSKs5
Oil Transfer Pump: amzn.to/3UAYTqX
Smoke Vacuum Leak Tester: amzn.to/3rVN9lG
ISTA D / BMW Coding Kit: ebay.us/Bndqwa
➢ Subscribe For Regular Videos ➢ goo.gl/x0Juyl
➢ Instagram: / georgeausters
➢ Facebook: / georgeausterspage
➢ Email: GeorgeAustersBusiness@gmail.com
➢Amazon Prime Free 30 Day Trial: amzn.to/2v6kVe5
➢Best Place For Car Parts: amzn.to/3DZykGe

Пікірлер: 139

@brianbiker Ай бұрын

Drop the oil and see if it’s full of swarf.. (check the filter too)

@theboltbreaker5829 Ай бұрын

Put crank pulley back on and check crankshaft end float if its manual gearbox get some one to press clutch pedal for you while you use a leaver pushed against the pulley face if you get movement in crank in and out thrust bearings are gone and could also have spun main bearing.

@alanparis7256 Ай бұрын

The thrust washers on either side of crankshaft internally have worn away and causing the crankshaft move side to side and partial sieze . Hence the pulley has no gap.

@daveyb89 Ай бұрын

This

@jetamotorsport8045 Ай бұрын

Yes this

@charliesoffer Ай бұрын

Where was the oil that contaminated the starter coming from?

@davidayling99 Ай бұрын

Oil on starter probably from crank moving back and forth pumping oil out past rear seal

@GeorgeAusters Ай бұрын

What makes you so sure?

@josephinegunning3027 Ай бұрын

Could be hydraulic lock because of a leaking injector

@thetechgenie7374 Ай бұрын

The thrust bearings are definitely done for, which also explains the oil built up on starter as crank play, plus lack of clearance on pulley, definitely pointing to bottom end failure. Also likely rod main bearings are done for or even spun, hence metal shavings. I would drop the oil pan and get access to bottom end would be where I would start. Likely low oil pressure due to ran low on oil, or lack of oil changes and tons of sludge is reason for failure.

@daveyb89 Ай бұрын

N47d20c bottom end failure is common the oil leaks are from crank play damaging them, Take the oil filter out the f series car and check it for swarf

@ramzsheikh9543 Ай бұрын

I ended up buying a new regulator and higher pressure fuel pump and it started and ran smoothly and still running

@meuer Ай бұрын

Well done... not seen that starter motor being the fault well done

@Aurora22586 Ай бұрын

Have you checked the oil filter for metal? I would check out the camshaft for wear. Maybe valves aren't opening properly and causing poor fueling ratio; therefore, the ECM is adding and subtracting fuel.

@ramzsheikh9543 Ай бұрын

From my experience on my e90 n47 it was the fuel presure regulator the main culprit mate

@flippy9133 Ай бұрын

maybe the metal on the seal was spun main bearing that oozed out, looked kinda coppery when you took it out

@GeorgeAusters Ай бұрын

I thought that but it was way too thin to be a bearing

@davidayling99 Ай бұрын

Crank endfloat causing it to have spun one or more main bearings is my guess

@paulspeedy4704 Ай бұрын

It's worth compression testing the cylinders (after replacing the front seal and pulley) as it is fairly non invasive but would certainly account for under power especially on a diesel. I fear the slivers of metal you found looked suspiciously like a spun bearing 🫣

@Doobie464 Ай бұрын

I have no idea but really enjoying your diagnostic thoughts and work.

@robc5955 Ай бұрын

Test the injectors to eliminate would be my next avenue.

@sebastianbrooke4534 Ай бұрын

Shine a light inside the tank if you see metal particals its the highpressure fuel pump.

@georgesafc6589 Ай бұрын

Loving the videos mate. Hope they keep coming

@iankirkpatrick6486 Ай бұрын

From experience, if it was the HPFP the car would take a long time to start, and after the starter was replaced, it tried to fire up. Also that wouldn't cause that knocking sound. Check the HPFP control valve (on side of pump) for swarf by all means, just to make sure, it's an easy/quick job.

@Smithy92 Ай бұрын

Ain’t no injector or fuel issue that, diesel injectors clack, knocking indicates bearing. And judging by oil under car it ain’t good… Drop the oil and inspect the oil filter first before anything.

@matty5057 Ай бұрын

It’s technically known and knackered!

@jaaguppung8132 Ай бұрын

This has the cp4. When fuel runs out the pump grenades itself, check the fuel rail for metal shavings

@mariusg6092 Ай бұрын

First thing you should do is to check the timing of the engine. I suspect that bad timing of the engine is causing the correction values of the injectors to go through the roof.

@stefanoES23 Ай бұрын

In the right side of the engine where the high pressure pump is, remove the pump pressure regulator and check if is any metal shavings, that will answer to your question, they are 2X T20 bolts if i remember corectly. the injectors are all bad i recon reman or exchange them all, they need to be as close to 0 value to assure a good engine run.

@markoutinthewild9481 Ай бұрын

feel your pain, ive just went through all that and ended up changing the engine, personally id change the fuel filter to start plus having bits of metal arround the crank isnt a good sign even if it is just part of the timing chain cover, that needs to be addressed by droping the sump, timing cover off and oil filter out to check for any metal, if there is then you know not to go any further and get another engine, if its clean then you need it running to see where the knocks coming from, deep sounding knock is probably the big ends, metal sounding knock could be piston slap or injectors, lots of different things can also cause it too tho, youn really need to hear it! wouldnt run it again untill youve checked the oil for metal tho. ATB Mark

@seangreenwood8331 Ай бұрын

check the end float on the crank,you can normally do it with a pry bar,those bits look like crank thrust washers

@GeorgeAusters Ай бұрын

Thrust washers are usually in the middle of the crank, not on the outside though

@seangreenwood8331 Ай бұрын

@@GeorgeAusters if they break away they can end up anywhere,what i would do is a put a dial indicator on the crankshaft pulley and lever it back and forth and see how much endplay you have..you should be able to get the specs for your model on line but if its a definite clunk sound it will be behond its tolerance

@GeorgeAusters Ай бұрын

@@seangreenwood8331 I don't think that is a sure way of knowing because my Mini Cooper S engine that I rebuilt had enfloat way higher than the specs - even with brand new thrustwashers.

@seangreenwood8331 Ай бұрын

@@GeorgeAusters could you not of used oversized thrust washers?....anyway easiest way to check on the bmw is simply get someone to press in the clutch while you watch the crank pulley,personally i would be draining the oil and taking the sump off to inspect the crank

@ThatOpelVectraC Ай бұрын

i would be checking the oil and filter for any metal swarf and also make sure you have no ''glitter''in the fuel pump and filter

@ski69 Ай бұрын

First you need to start with the leak down and compression test.....then have the injectors sent out for test or rebuilt.....

@charlieoscar09 Ай бұрын

Hope you can sort it George sorry i cannot offer any advice....Everything i know i've learnt from you 😉

@sallyheylen9812 Ай бұрын

I would fit a new oil seal and get the engine running so that you track where the knock is coming from

@jorredegendt5408 Ай бұрын

Take off the sump. See if a rod is bent. I hve an Alfa 1.9 jdtm. Turbo was changed but still no luck. After looking around everything and no fault codes so can it be internally. Can still run with a bent rod or a bent valve without drawing codes. Use an inspection camera to check valves

@mcplutt Ай бұрын

I think you need to remove the metering unit from the CP4 and look for metal particles.

@yosemitesam283 Ай бұрын

When you fired it up it certainly doesn’t sound like noise from the bottom end, sounds more like noisy injectors, if no faults showing regarding fuel pump I’d say try your E91’s injectors in it. Surely can’t hurt for a few seconds running and may give you a faster answer, hope it’s something cheap and easy for you. On another note I’ve just last Saturday bought an F30 335d M sport, I love it and will now be selling my E91. Keep the updates coming and good luck with it, Joe

@ramzsheikh9543 Ай бұрын

Yh mines did the same and kept thinking it was injectors but it wasn't the code I was getting was fuel rail then it turned out fuel regulator absolute ball ache a simple small part caused a massive headache for me

@NotSoNano Ай бұрын

Use ista to do a smooth/rough idle test then reset injector corrections. Then do another idle test and see if it’s any better

@daviddorado5632 Ай бұрын

Maybe the tips of the injectors are clugged with carbon. Or leaking too

@MaxJames597yompfitness Ай бұрын

timing chain stretched causing imbalance on the end balancer

@Masteranddisaster13 Ай бұрын

There was a noise like a belt squeal. Thats probably your bottom end bearings.

@GeorgeAusters Ай бұрын

Whoops 😅

@Aurora22586 Ай бұрын

If the high pressure fuel pump is the cause, you would need to clean out the entire fuel system before you put anything new in; otherwise, you will clog up the new stuff. Check if there's any metal shavings in the fuel system, check the high pressure fuel pump for wear to rule that out first.

@xenontetra1758 Ай бұрын

Love the n47 content, might get one myself one day with a failed chain to fix and sell on

@user-ep2sx6rp4y Ай бұрын

Check the oil for metal sounds bottom end maybe remove the sump and check

@-sargntclashroyaleandmore-491 Ай бұрын

When you shouted stop got me 😂

@GeorgeAusters Ай бұрын

Almost lost all the oil 😂

@ParzivalPheonix Ай бұрын

My pulley went in a car park once, couldn't move the car, it would start but wouldn't move.

@andrewthompsonuk1 Ай бұрын

i guess you check for swarf in the hp pump. May only be a few bolts to take the bore out.

@KariKorvela Ай бұрын

Those chips behind oli seal could be parts of broken/spun first main bearing, unfortunately…

@karter5351 Ай бұрын

As they say down the BMW Fim Club, Der BearingBigEndun Schitzunselfen

@GeorgeAusters Ай бұрын

Yeah I did think that but it’s too thin to be a bearing and it’s part of the casting

@danmoney9932 Ай бұрын

The presence of those metal.shavings can't be right though and must be something to do with the problems?

@salty987 Ай бұрын

Fuel should not make it squeak like that. That worries me more then the knocking.. Try to change the good injector cylinder 3 for 5, if the numbers change thats good, if it dosent change its a big risk its bad compression, or just do a compression test first then you dont need to change injectors.

@savvaspierides7260 Ай бұрын

Nice work George. Any ideas for a good diagnostic with software access to the car to repair the 360 cameras?

@equiinoxxpvp2718 Ай бұрын

Engine rebuild video would be fun ;) get a good look at that crankshaft and the bearings/timing chain

@GeorgeAusters Ай бұрын

Don’t have the time or space to do a rebuild.. also don’t think it would be economically viable

@911engineguy Ай бұрын

For some reason, playing this at 1.25x sounds better to me

@eusvt Ай бұрын

Does it have a cp4 hpfp ? Remove it and check for metal shavings , they are know to fail if car is ran on low fuel.

@Hancock_nl Ай бұрын

I doesn't sound healthy George, and that piece of metal is concerning. Before touching any fuel related parts i would need to be sure that bottom end, head and timingchain are fine. My first step would be like many already mentioned: Check oil and filter.

@GeorgeAusters Ай бұрын

Yeah think I’ll check the oil filter before I do anything else👍🏻

@Vitus_LRXGA Ай бұрын

can it be that a injector has failed and it just drips?

@gunther5840 Ай бұрын

I’m going with the majority here; at least 1 main bearing gone. (That piece of metal you found is exactly how it would look like; razorsharp flims of metal, also that knock sounds too heavy to be injector related). Confirm this theory bij looking for metal in oil filter, and dropping the sump, it should be immediately clear. If correct, engine swap or rebuild if possible (crankshaft still within specs, bearing rods, cilinder state,…) is the only option, but what was the root cause? Still possible to undo the sale or negotiate something? At least get some insights from previous owner; oil change interval respected or complaints reported?

@marcustaylor9210 Ай бұрын

Does it have petrol in by mistake, that would give a similar effect,

@jrn6471 Ай бұрын

Hi George. The timing might be slightly off, causing knocking due to slight contact between valves and pistons....These engines are notorious for timing chain failure, but often stretch slightly before it finally snaps or that the guides collapsing. Don't replace any injectors before you determine if the timing is correct is my advice. As you know you can throw parts on a BMW and still face the original issue...;-)

@GeorgeAusters Ай бұрын

Timing chain was done in 2022

@jrn6471 Ай бұрын

@@GeorgeAusters But done correctly and by whom?

@maxspace24 Ай бұрын

My thought so too. But maybe the plastic from the timing cover is made of chinesium ;)

@Vitus_LRXGA Ай бұрын

hey george, what is if you measure the pressure of the rail bar. If its good when the engine is turning it cant be the high pressure fuel pump.

@PaulRansonArt Ай бұрын

Could this be diesel knock? If its worse when cold then clears up when warm - that would be my guess. Two dead injectors and maybe injector timing will cause that sort of symptom. They sound terrible if that's the cause. - Good luck 😃😃😎😎

@chrisgermann6658 Ай бұрын

That from my end looks like some the casing has chipped away around the crankshaft. Is it a tapered/extruded diameter to help seal the o-ring?.

@BMWBAS Ай бұрын

Careful turning the harmonic balancer with just one of the bolts. Try to use two tools to distribute the stress or get the BMW tool that fits over all four. Love your videos. Hello from Portland, Oregon.

@GeorgeAusters Ай бұрын

Not really needed, especially when I’ll be replacing these bolts

@BMWBAS Ай бұрын

@@GeorgeAusters I guess that’s more of a concern when you are putting the belt on with a new harmonic balancer.

@keithfraser5910 Ай бұрын

Main bearing seized and spun out

@ThomasClifton-sk6br Ай бұрын

It is a tricky one but with the timijg chain being at the back of the engine taking it appart is going to be a challenge. Personally I think your best taking the engine out of the car getting it on a stand and giving s full going through.

@GeorgeAusters Ай бұрын

Money will start adding up if I rebuild it and leave me with no profit in the car

@allandalton7350 Ай бұрын

its bottom end pull it out crank regrind shells possible conrod and it'll be all good I've done a couple off these now and bottom ends are weak due to long service intervals

@GeorgeAusters Ай бұрын

What makes you think it’s not the injectors?

@inguss4891 Ай бұрын

I owned f30 !hope to get some tips!😉What code reader using mate? I will keep on eye!All the best mate🤘🏻

@GeorgeAusters Ай бұрын

My scan tool is linked in my description👍🏻

@marcelh2341 Ай бұрын

This engine is done. Sounds like crankshaft or piston rod bearing damage.

@andrewthompsonuk1 Ай бұрын

My feeling is fuel system. It appears to have even compression but runs badly.

@user-gz8ou2sl6x Ай бұрын

great bit of content hope you get to the bottom of the problem soon stunning looking motor all the same

@steveng5503 Ай бұрын

Is it a knock? Played it back a couple of times. Maybe start with simple things like check fuel, pressures etc. then maybe swap 2 with 4 and check codes again. Clearly you’re keen to move on but this car isn’t gonna allow that. Madness running engine with seals removed. When next running maybe check blowby and oil pressure. Compression? Last thing… I had similar poor running experiences and was leaking injector… my opinion derv destroys synthoil. No doubt the chain gang will pipe-up! 👍🏻

@andyblood8497 Ай бұрын

Have you checked the crankshaft end float?

@GeorgeAusters Ай бұрын

No I haven’t

@hansenyeo2117 Ай бұрын

Running out of fuel is not good for the high pressure rail pump, since diesel fuel also acts as lubricant to the pump mechanism. Also, there is a procedure in ISTA to bleed out the air trapped in the fuel line before one tries to start the engine again (might had hard time to start tho)

@GeorgeAusters Ай бұрын

Already bled the fuel system when I went to pick the car up👍🏻

@NinpoUK Ай бұрын

I don't think you can ignore them running out of fuel completely before the problems started to occur. Crap/air/both still in the lines perhaps? How old does the fuel filter look? I'd def make sure I'm happy the fuel system is clean before looking at a new block George mate. I might be misremembering but I'm sure a slight mistiming issue can sound like a knock which you'd get with delayed compression/firing on a line with crap in it.

@GeorgeAusters Ай бұрын

They said they replaced the fuel filter and I did a bleed of the fuel system straight after I collected the car but still the same

@NinpoUK Ай бұрын

@@GeorgeAusters maybe gunk killed an injector/is still in there then. My next move would be putting all back together and using topdon to test each injector or at least be able to turn it over more and zero in on that knocking noise while not having to worry about the oil pissing out maybe?

@florinlepadatu5648 Ай бұрын

enine out, tear it apart see the damage than decide if worth repairing or not. That piece of metal shouldn't be there, you cannot sell this car until you know exactly what you are selling imho...

@GeorgeAusters Ай бұрын

May not need the engine out if it’s just fuel related

@paulspeedy4704 Ай бұрын

Engine earth strap?

@steviem2224 Ай бұрын

Well personally George I’d go and get a beer it looks a bit dark mate then sleep on it and start again😀

@GeorgeAusters Ай бұрын

😂

@pauljbusby Ай бұрын

It could be anything...literally everything on a BMW fails and I mean everything. Ive owned 2 of them. I now own 2 Toyotas....Pot #4 is toast BTW..Low compression. Engine out. The injectors is compensating for low compression on CYL 4 particularly

@ianjenkins4641 Ай бұрын

It’s spun a shell or two. 2nd hand engine time

@GeorgeAusters Ай бұрын

What makes you so sure?

@ianjenkins4641 Ай бұрын

Drop the oil and look at what’s in it. Also filter. That knock is not fuel related it’s bottom end. Plus you would have fuel pressure codes if it was pump etc.

@toonmag50 Ай бұрын

You enjoy your diy work with BMW's. I've been driven mad with my wifes unreliable BMW, and given up "fiddling" Paid a big chunk of change to the "man" in a Sheffield BMW specialist and its all fixed.... for now.

@thejudge-kv2jk Ай бұрын

Now its 'fixed' for the love of god move it on.

@toonmag50 Ай бұрын

@@thejudge-kv2jk I would drop it down a pit shaft and walk away, but unfortunately it's the wife's car and for some reason likes it.

@Jonbuildz Ай бұрын

You'll only end up black bagged and kicked out the house if you get rid mate haha, maybe bin the mrs off ?

@SteveDull Ай бұрын

I enjoy messing around with my e82 with the same engine, but it's not the main wheels - or the misses runabout 🙂

@tomasis7 Ай бұрын

remove oil pan

@BmwCCCrepairsUK Ай бұрын

😢

@Beaulocks_ Ай бұрын

Crank has "walked".......shagged thrust washers?

@GeorgeAusters Ай бұрын

What makes you say that?

@zainsajjad9930 Ай бұрын

Bottom end bearings gone

@GeorgeAusters Ай бұрын

What makes you say that?

@flippingcarsrepairs Ай бұрын

As much luck as im having on my trading series 😂😂😂😮

@craigrice1960 Ай бұрын

Is it a injector clamp 🗜️

@italianjob-vx6hp Ай бұрын

New starter motor , Get i all injectors refurbished first

@GeorgeAusters Ай бұрын

So you think it’s injectors causing the knocking?

@italianjob-vx6hp Ай бұрын

@@GeorgeAusters Well i know they can do this and on a bmw 6 cylinder it is nearly always cylinder 3 !

@KingDavid9999 Ай бұрын

peice of metal in engine, drop oil pan to find it before it blows

@AlDidit-tf1zo Ай бұрын

2 liter 4pot, built in Birmingham by ex rover employees. Should have brought the straight 6.

@GeorgeAusters Ай бұрын

Straight 6s are a lot more money

@AlDidit-tf1zo Ай бұрын

@@GeorgeAusters Yeh but they usually do more miles without imploding. If you ignore the main dealers advice and service it yourself, they’re good for at least 400.000. My last two did on the same turbo and timing chain.

@mini_special Ай бұрын

Bottom end failure for sure.

@matthewcoombs6085 Ай бұрын

this is 99% sure the n47 engine absolute worst engine ever i grantee the chain has snapped to very streched

@GeorgeAusters Ай бұрын

Timing chain was done a year ago

@user-lt5co8qq1b Ай бұрын

It's to old .scrap the car and move on .

@GeorgeAusters Ай бұрын

Too old? It’s the newest car I’ve ever owned 😂

@maxspace24 Ай бұрын

You clearly don’t know George ;)

@styz8312 Ай бұрын

At all. But should of stayed 2009 and older lol 😂 I had a e91 330d m57 sold it, 6 months later iv brought another one but got the m sport high spec and I'm never selling it 😂