Jeep Liberty Project Pt. 7- Front Suspension and Brakes

No video

Jeep Liberty Project Pt. 7- Front Suspension and Brakes

Рет қаралды 3,457

Күн бұрын

In this video I replace the front brakes and several small suspension parts as well as install the front piece of the lift kit and replace differential fluid. Enjoy!

Пікірлер: 22

@homeforhomies8415 11 ай бұрын

So glad I found your channel. I’m doing a lot of this for the first time (I’m not a “car guy”) and this has been crazy helpful.

@atouchofhutchad 11 ай бұрын

I’m very happy you found this helpful! Us non car guys have to stick together lol

@toonyseph7561 Жыл бұрын

This is definitely a labor of love! Awesome!

@atouchofhutchad Жыл бұрын

Yes! Thank you!

@toonyseph7561 Жыл бұрын

Eventually if you want to upgrade the lift, try getting Old Man Emu 2927 up front and 2948 in the rear. It will ride better than it did when it came off the lot. I paired that with Bilstein Shocks as well

@atouchofhutchad Жыл бұрын

Great info! I’ll definitely need an upgrade in the future

@jasonjulian1 Жыл бұрын

@@atouchofhutchadi can attest.. I have the OME parts and they're fantastic. Being I also live in MI, with our roads... The best suspension you can get is almost a requirement

@MrNewff Ай бұрын

I just did the same with my 2010 Liberty. The only thing I didn't replace in the front was the tie rods.

@atouchofhutchad Ай бұрын

@@MrNewff I bet it looks nice! It’s a lot of work.

@Nonamestranger126 4 ай бұрын

You can use a fluid transfer pump and pump out the old diff fluid from the fill plug

@atouchofhutchad 4 ай бұрын

Great tip! Thanks!

@nikosvasilakopoulos8993 7 ай бұрын

Well done for all your fine work! I have a 2004 Jeep KJ since new, and my only comment is to avoid such lifts. You will have issues with your CV joints, they cannot work properly in such extreme angles. My advice is to go with the OME lift, the Jeep will handle much better than stock. Also use Terraflex 1903200 front bump stops and two hockeypucks in each side on the rear. Finally, if you have spare badget buy the Jeepin by Al control arms. I hope you enjoy your Jeep!

@atouchofhutchad 7 ай бұрын

Thanks for the tips! I’m going to do some research and see if I can implement some of those!

@toonyseph7561 Жыл бұрын

You might wanna get JBA Offroad upper control arms later on. They’re definitely expensive, but definitely worth it

@atouchofhutchad Жыл бұрын

These are the exact upper control arms I have picked out!

@toxicliver 11 ай бұрын

Hey buddy, I just wanted to ask if you're sure the lift spacers go on the bottom? I'm sure iv seen other lift kits with the spacer at the top of the strut ? Just wondered. Anyway, good luck with your jeep good stuff 👍

@atouchofhutchad 9 ай бұрын

Yeah I’m sure they do because there is a hole for the bottom of the strut to fit into and the strut has to bolt to the body of the Jeep inside the engine bay.

@madman432000 24 күн бұрын

I got JBA arms for mine, not sure they are still made though.

@atouchofhutchad 24 күн бұрын

I think they still are made for this Jeep! I’m excited to get them soon. Hope you like yours!

@madman432000 24 күн бұрын

@@atouchofhutchad had them since 2016 and no issues. Did require an alignment.

@ChristianMendezS Ай бұрын

Hi, where did you bought the lift kit?

@atouchofhutchad Ай бұрын

www.roughcountry.com/product/jeep-suspension-lift-kit-68731?C&C%7Cm%7C%7Cname_first_68731-a&gad_source=1&gbraid=0AAAAAD83JzpSajkuEVW7r_seS6nMqrz8-&gclid=Cj0KCQjwwO20BhCJARIsAAnTIVTMfgnvdwX_MhtxAU8trEq4yeRuBxvNWPL1J91mkGZe3F4-EeIW5dwaAshNEALw_wcB I’m having a hard time finding the original kit I purchased but this is basically it just for newer models. There should be other brands that make them as well. Hope that helps!