Can you get away with out cutting the bed plastic you should get a Milwaukee instead lol lol
@Jimmy2Tech2 ай бұрын
No, Not really. I like yellow. Lol
@razah23392 ай бұрын
@@Jimmy2Tech i was jk cheers
@chrispelkington31882 жыл бұрын
Thanks for the video. Have you noticed any rattling of the box going over bumps and pot holes?
@Jimmy2Tech2 жыл бұрын
Negative. It all seems pretty quiet. I would suppose it also matters what you put in there and what other stuff you have in your bed.
@wikdracing32532 жыл бұрын
Any issues with clearance when towing the fifth wheel? That was my only concern before purchasing one of these.
@Jimmy2Tech2 жыл бұрын
Good to go with a fifthwheel hitch. No clearance issues at all. This case remains installed when we tow our fifth wheels. Please keep in mind that we have a 6.75 ft box and not a 5.5 ft which may cause clearance issues.
@wikdracing32532 жыл бұрын
@@Jimmy2Tech Good to know. I have a 6.75' bed as well.
@wcgems7 ай бұрын
"isoscillator"
@TimRatliff-fs7ze Жыл бұрын
I have a 2013 F-250 with a sprayed-on bed liner. Will this create any unique problems or will the tool box mount normally?
@Jimmy2Tech Жыл бұрын
It should mount normally according to their website.
@THEEVAAN3 жыл бұрын
Hi guys You haven’t mentioned anything about what year is this truck?
@Jimmy2Tech3 жыл бұрын
This is a 2017 F250:)
@268Brookland2 жыл бұрын
2015 to 2021 is the same.
@nvcoka Жыл бұрын
Will plywood sheets still lay down in the bed or does that take up too much room?
@Jimmy2Tech Жыл бұрын
It will allow plywood to still fit.
@fishman802 жыл бұрын
does the cover lock at the rear side rails with latches? i have a tonno pro so was wondering if this would clear the latches
@Jimmy2Tech2 жыл бұрын
It will depends on the latching system. If your tonno pro has the Spring loaded handle(the 4 to 5 inch handle that you pull down) that latches it will not fit. If it has the type the that you lock into place and turn the handle 45 degrees (the handle is horizontal and not vertical) than you'll be good. This swing box only gives you a few inches of clearance above it. But it works with the tonno cover on the truck.
@268Brookland2 жыл бұрын
I have the pull down latches and it works fine. You just have to have the cover latch on and then latch the swing case. Only problem is that you need to unlatch the swing case before you can open the tonneau cover. But it will work.
@fishman802 жыл бұрын
@@268Brookland Oh OK I never thought of that. So the latch will fit behind the swing case, interesting . I think I can probably live with that. I’m honestly not opening my bed cover a whole lot anyhow. thx for the info
@268Brookland2 жыл бұрын
@@fishman80 yessir. It’ll work just fine. When you want to latch and unlatch your cover you have to unlatch the swing case.
@fishman802 жыл бұрын
@@268Brookland Thank you sir and merry Christmas to you
@Michael-hj3jg3 жыл бұрын
Why’d you take out the light you don’t have to
@Jimmy2Tech3 жыл бұрын
What light are you referring to?
@augustito19773 жыл бұрын
@@Jimmy2Tech probably is talking about the taillight that you removed.....too much cutting on the poor Bedliner....if you washed lots of water will be accumulated under...good job , but i pass
@268Brookland2 жыл бұрын
You definitely have to take the tail light out.
@MultiMediaMikes Жыл бұрын
I dont think removing the bedliner rear piece is needed, if anthing, the bracket will hold it to the bedwall better like how its out of the top of the top cap piece that should be covering the top edge of the bedliner. And @13:40 you can see the cut part of the bedliner sticking out more than if it was held tight against the rear bracket.
@Supertramp012 жыл бұрын
LMFAO...That bedliner is swiss cheese at this point,,, may well take it out and put a bed mat down. Straight up hack job
@peterkolovos30792 жыл бұрын
Seemed too flimsy to me. I was hoping they were beefier, and it appears they don't hold a lot of items.
@Jimmy2Tech2 жыл бұрын
It is a niche item for sure. You can hold some stuff for sure but it deffinately isn't for everyone.
@Michael-hj3jg3 жыл бұрын
You didn’t need to cut bedliner swing case says ok to install over bed liner you made it to hard for sometime easy!
@Jimmy2Tech3 жыл бұрын
Hey there! For our application we needed to because we have the fifth wheel hitch in there which messed with the orientation of the bed liner when we installed it, preventing us from closing the swing case. In a truck without the fifth wheel hitch/a good bed liner you should be okay to install over the bed liner.