I have issue in eletrical malfunction, ENGINE RPM lever is not working, what was issue may be
@rabasalltv8095 Жыл бұрын
Informative and helpful
@jlcworkshop Жыл бұрын
Salamat manoy
@fajalkhan571511 ай бұрын
❤🎉 thanks 🙏
@jeffvids9 Жыл бұрын
Sending full support from san vicente cam norte...pashout po lods
@jlcworkshop Жыл бұрын
Cge padi d lang kc nakakagawa pa ng bagong video.salamat
@nooralamusmani9116 Жыл бұрын
How much clearance you fixed
@amanullahkhan5073 Жыл бұрын
Where is your workshop
@KapitAnnVins Жыл бұрын
wow galing talaga hehe
@jlcworkshop Жыл бұрын
Hahahahha tsamba lang
@autoroyal2751 Жыл бұрын
please make a 30 minutes explanation video on adjusting valves, tdc, ebs and the logic. please please . even if you dont film at the truck, oits ok if you flm in front of a drawing board and explain why TDC and all the rest. what means running mate etc . thank you . make a video so that alll normal DIY truck owners should understand . it will be the most amazing video i assure you .
@velmuruganmurugan4201 Жыл бұрын
I have issue mantruck Model 2015, - 385
@MohdZabehKhan-rh5zm8 ай бұрын
Thank sir
@Sir_Nick13 Жыл бұрын
Hello. Why you must make first EVB 0 clearance to adjust exhaust valve?
@jlcworkshop Жыл бұрын
Hi sir,to get an accurate adjustment and clearance.
@hassansherazi-zc7px Жыл бұрын
Hello brother i want to my vehicle where is your workshop
@peteruba12606 ай бұрын
❤
@allandesertmechanic701010 ай бұрын
Galing ser salamat sa pagshare done watching like subscribe done
@WarvenCuevas7 күн бұрын
Magandang gabi brod. Baka matulongan m ako truble shot itong tinatrabaho makina sa man cla 18_280 mag overheat. Akin na ito top overhaul. Pinalitan ko na ito linner, piston ring cylender head gasket. Nozzul tip. Bagong calebret ang injection pump.umaandar na. Pagkatapos palyado. Mag overheat. Dati overheat ang problema nito.
@jlcworkshop6 күн бұрын
Saan location mo sir?
@jlcworkshop6 күн бұрын
Ano ang injection pump nyan sir?rotary ba or inline.sa ppagkakatanda ko kapag rotary injection pump.35degress btdc ang injection timing.kung inline nman ay 13 degrees
@markcabzzz42639 ай бұрын
Boss matanong ko lng boss ano ba iyung dapat gawin boss pag ang man tgm 18.240 nag indicate sa cluster nang "check fuel supply" sana mapansin boss salamat
@velmuruganmurugan4201 Жыл бұрын
How are you
@edwardmorales30105 ай бұрын
Good pm bro anong max and min torque sa cylinder head d2066 /con rod at main bearing
@jlcworkshop5 ай бұрын
Nakalimutan ko sir nandon kc sa record book ko.pero pakisearch din po sa google baka meron yan.sa pagkakatanda ko.yong main bearing ay 300nm plus 90 degrees.conrod bearing 100nm plus 90 degrees at cylinder head 300nm plus 90 plus 90.
@kSA_679.10 ай бұрын
Shot out paps
@aldwinobenza1627 Жыл бұрын
Good job sir . Saan Po kayo sa saudi Po .Anong company Po??
@jlcworkshop Жыл бұрын
Dito ako sir sa al kharj
@charlitoautor8243 Жыл бұрын
...boss pwd malaman kung anong dapat gawin...nakalagay sa dash board ...malfunction on board computer...tas ayaw na nya mag matic magagamit mo as a manual nlng...salamat boss...
@jlcworkshop Жыл бұрын
@@charlitoautor8243 sensya na po sir d kita nareplayan agad ok na po ba yong unit nyo?
@sukhwindermahal7073 Жыл бұрын
Good morning sir I am facing a problem with D2676 MAN eingen. There is creating pressure in readiator i changed readiator and air Compressor pump but problem is still as it is . Please help
@jlcworkshop Жыл бұрын
Hi sir.what kind of cylinder head that one sir?is that single inline cylinder head or indibidual?
@jlcworkshop Жыл бұрын
Actually that was also happened here.creating pressure even radiator and air compressor are new.so we was dismantled the head and check the liner and clean.the after that,pressure is gone
@sukhwindermahal7073 Жыл бұрын
Singl head
@sukhwindermahal7073 Жыл бұрын
Make a vedio we will thankful to you
@sukhwindermahal7073 Жыл бұрын
Clean liner you means Piston liner or water lines
@ariunboldgonchigsuren Жыл бұрын
Hi
@rabah8452 Жыл бұрын
Hello sir,,Although the letter N does not appear, the engine is running... Please what is the reason
@jlcworkshop Жыл бұрын
Hi sir,actually i cannot experience that kind of trouble yet,but i want to know if when you shift in reverse,letter R showing?
@jlcworkshop Жыл бұрын
And hows if you shift in first gear or second gear third gear.number is showing or not?
@rabah8452 Жыл бұрын
yes sir it shows the number R....and everything is fine..